共找到 741 条与 瓶、小罐、瓮 相关的标准,共 50 页
Glass containers — Internal pressure resistance — Test methods
本文件规定了瓶盖用二维条码的技术要求和检测方法。
Technical requirements of two-dimensional bar code for closures
本文件规定了聚乙烯塑料瓶中空吹塑成型技术规范的术语定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于中空吹塑成型聚乙烯塑料瓶的生产和检验。
Technical specifications for hollow blow molding of polyethylene plastic bottles
本文件规定了食品包装用聚酯(PET)瓶坯(以下简称“瓶坯”)的分类、要求、试验方法、检验规则及标志、包装、运输、贮存。
Polyester(PET)preform for food packaging
本文件规定了食品包装用聚酯(PET)容器的产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。
Polyester(PET)container for food packaging
本文件规定了固体食品包装用塑料瓶的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以聚乙烯(PE)、聚对苯二甲酸乙二醇酯(PET)、聚丙烯(PP)为原料,采用吹塑工艺制成的容量不大于8 L的固体食品包装用塑料瓶。
Plastic bottle for solid food packaging
1.1 This test method covers a gas chromatographic procedure for the determination of the ppm residual acetaldehyde (AA) present in poly(ethylene terephthalate) (PET) homopolymers and co-polymers which are used in the manufacture of beverage bottles. This includes sample types of both amorphous and solid-stated pellet and preform samples, as opposed to the bottle test, Test Method D4509, an acetaldehyde test requiring 24 h of desorption time at 23 °C into the bottle headspace and then the concentration of the headspace quantified by a similar GC method. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Determination of Residual Acetaldehyde in Polyethylene Terephthalate Bottle Polymer Using an Automated Static Head-Space Sampling Device and a Capillary GC with a Flame Ioniza
本文件规定了液态乳品包装用单层吹塑瓶(以下简称吹塑瓶)的术语和定义、分类与结构、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于以聚乙烯(PE)树脂、聚丙烯(PP)树脂、聚苯乙烯(PS)树脂、聚对苯二甲酸乙二醇酯(PET)树脂为主要原料,采用注-拉-吹、注-吹、挤-吹等吹塑工艺成型的1 500 ml以下(含1500 ml)液态乳品包装用单层吹塑瓶。 本文件不适用于热灌装吹塑瓶。
Single-layer blowing bottle for liquid dairy packaging
1 Scope This document specifies the design and dimensions of the 29 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This document applies to finishes designated as PET finishes 29/25 (12,6). The dimension (12,6) is the height in millimetres from the top of finish to the bottom of the support ledge. This finish can be used for aseptic filling and filling which utilizes nitrogen pressure where the internal overpressure does not exceed 1 bar maximum. This finish is designed to accept only a tamper evident plastic closure, including those with an attachment feature.
Packaging. Rigid plastic containers. PET finish 29/25 (12,6)
本文件给出了超洁净灌装口服液用一步法塑料瓶的术语和定义、技术要求、试验方法、检验规则及标志、包装、运输、贮存。
One-step injection and blow molding bottles for ultra - clean filling oral liquid
This GSO Standard Specification is concerned with requirements and test methods for plastic bottles used for bottling and preservation of water (Water Flasks), used for filling and preserving drinking water.
Plastic Bottles Used for Water Bottling (Water Flasks)
This document specifies the test method to determine the capillarity of cylindrical cork stoppers. It consists in measuring the capillary rise by dipping in a hydro-alcoholic solution containing a dye. Two methods using the same procedure but different concentrations of hydro-alcoholic solutions are described. It is applicable to all types of cylindrical cork stoppers, ready for use.
Cylindrical cork stoppers — Physical tests — Part 8: Determination of capillarity
BS EN 17829. Glass packaging. 28 millimetre-screw finishes for glass containers (MCA range). Dimensions
BS EN 17827. Glass packaging. Traditional method sparkling wine finishes (26, 29, 36 mm)
Testing method for thermal shock of carbonated beverage bottles
Method of measurement of glass thickness forcarbonated beverage bottles
Testing method for impact of carbonated beverage bottles
Glass containers-Resistance to vertical load-Test methods
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号