75.180.30 容积设备和容积测量 标准查询与下载

BS EN ISO 7278-2:2022 石油测量系统 管道检验仪设计、校准和操作

Petroleum measurement systems - Pipe prover design, calibration and operation

ASTM F3136-22 用动态累积法测定通过塑料薄膜和薄板的氧气传输率的标准试验方法

1.1 This test method covers a procedure for determination of the transmission rate of oxygen gas through plastics in the form of film, sheeting, laminates, coextrusions, coated or uncoated papers or fabrics. 1.2 This test method is not the only method for measurement of the oxygen transmission rate (OTR). There are other methods of OTR determination that use other oxygen sensors and procedures. 1.3 The values stated in SI units are to be regarded as standard. Commonly used metric units used to report Oxygen Transmission Rate are included in Terminology, Procedure, Precision and Bias sections and in the Calculation section of the Appendix. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Oxygen Gas Transmission Rate through Plastic Film and Sheeting using a Dynamic Accumulation Method

EN ISO 7278-2:2022 液态烃.动态测量.计量校正系统.第2部分:管道校准

This document provides descriptions of the different types of pipe provers, otherwise known as displacement provers, currently in use. These include sphere (ball) provers and piston provers operating in unidirectional and bidirectional forms. It applies to provers operated in conventional, reduced volume, and small volume modes. This document gives guidelines for: — the design of pipe provers of each type; — the calibration methods; — the installation and use of pipe provers of each type; — the interaction between pipe provers and different types of flowmeters; — the calculations used to derive the volumes of liquid measured (see Annex A); — the expected acceptance criteria for fiscal and custody transfer applications, given as guidance for both the calibration of pipe provers and when proving flowmeters (see Annex C). This document is applicable to the use of pipe provers for crude oils and light hydrocarbon products which are liquid at ambient conditions. The principles apply across applications for a wider range of liquids, including water. The principles also apply for low vapour pressure, chilled and cryogenic products, however use with these products can require additional guidance.

Petroleum measurement systems - Part 2: Pipe prover design, calibration and operation (ISO 7278-2:2022)

ISO 7278-2:2022 石油测量系统.第2部分:管道校准仪的设计、校准和操作

Petroleum measurement systems — Part 2: Pipe prover design, calibration and operation

SY/T 7667-2022 石油和液体石油产品 自动计量系统技术要求

Technical requirements for automatic metering systems for petroleum and liquid petroleum products

22/30461108 DC BS EN ISO 12185 原油、石油产品及相关产品 密度的测定 带振荡 U 管传感器的实验室密度计

BS EN ISO 12185. Crude petroleum, petroleum products and related products. Determination of density. Laboratory density meter with an oscillating U tube sensor

22/30461348 DC BS ISO 4266-4 石油和液体石油产品 自动方法测量储罐液位和温度 第 4 部分：常压储罐温度测量

BS ISO 4266-4. Petroleum and liquid petroleum products. Measurement of level and temperature in storage tanks by automatic methods - Part 4. Measurement of temperature in atmospheric tanks

22/30461339 DC BS ISO 4266-1 石油和液体石油产品 自动方法测量储罐液位和温度 第 1 部分：常压储罐液位测量

BS ISO 4266-1. Petroleum and liquid petroleum products. Measurement of level and temperature in storage tanks by automatic methods - Part 1. Measurement of level in atmospheric tanks

22/30444610 DC BS ISO 10976 冷冻轻质烃流体 液化天然气运输船上货物的测量

BS ISO 10976. Refrigerated light hydrocarbon fluids. Measurement of cargoes on board LNG carriers

GSO ISO 13739:2022 石油产品 将燃油转移至船舶的程序

This document specifies procedures and requirements for the transfer of bunkers to vessels involving bunker tankers, road tankers and shore pipelines. It is applicable to pre-delivery, delivery and post-delivery checks and documentation.

Petroleum products — Procedures for the transfer of bunkers to vessels

BS ISO 7507-2:2022 石油和液体石油产品 立式圆柱形储罐的校准光学参考线法或电光测距法

What is ISO 7507-2 - Calibration of vertical cylindrical tanks about?    ISO 7507 discusses petroleum and liquid petroleum products. ISO 7507-2 is the second part of the ISO 7507 multi-series and discusses the calibration of vertical cylindrical tanks and the optical-reference-line method or electro-optical distance-ranging method.   ISO 7507-2 is suitable for tilted tanks with up to 3 % deviation from the vertical provided that a correction is applied for the measurement tilt, as described in ISO 7507-1 . These methods are alternatives to other methods such as strapping ( ISO 7507-1 ) and the optical-triangulation method ( ISO 7507-3 ).   Who is ISO 7507-2- Calibration of vertical cylindrical tanks for?

Petroleum and liquid petroleum products. Calibration of vertical cylindrical tanks - Optical-reference-line method or electro-optical distance-ranging method

ISO 7507-2:2022 石油和液态石油产品.立式圆柱形储罐的校准.第2部分:光学基准线法或光电测距法

This document specifies methods for the calibration of tanks above eight metres in diameter with cylindrical courses that are vertical. It provides two methods for determining the volumetric quantity of the liquid contained within a tank at gauged liquid levels. NOTE For optical-reference-line method, the optical (offset) measurements required to determine the circumferences can be taken internally or externally, provided that insulation is removed if tank is insulated. The methods are suitable for tilted tanks with up to 3 % deviation from the vertical provided that a correction is applied for the measurement tilt, as described in ISO 7507-1. These methods are alternatives to other methods such as strapping (ISO 7507-1) and the optical- triangulation method (ISO 7507-3).

Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 2: Optical-reference-line method or electro-optical distance-ranging method

BS EN ISO 8222:2020+A1:2022 石油测量系统 校准 体积测量、试验罐和现场测量（包括液体和材料特性的公式）

What is ISO 8222 – Calibration of volumetric petroleum measurement systems about? ISO 8222 is an International Standard that discusses petroleum volumetric measurement systems. Volumetric, or capacity, measures are used to provide an accurate measure of volume, thereby providing a calibration reference for other volume-measuring devices, such as pipe displacement provers or flowmeters. ISO 8222 describes the design, use, and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. ISO 8222 is applicable to the petroleum industry; however, it may be applied more widely to other applications. ISO 8222 also provides reference formulae describing the properties of water and other fluids and materials used in volumetric measurement more generally. Note: ISO 8222 excludes measures for cryogenic liquids and pressurized measures as used for liquid petroleum gas (LPG) and liquefied natural gas (LNG). Who is ISO 8222 – Calibration of volumetric petroleum measurement systems for? ISO 8222 on the calibration of volumetric petroleum measurement systems is useful for:

Petroleum measurement systems. Calibration. Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials)

EN ISO 8222:2020/A1:2022 石油测量系统.校准.用容积基准测量罐的校正温度 包含修改件A1,2022

Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) - Amendment 1: Correction of two typographical errors (ISO 8222:2020/Amd 1:2022)

ISO 8222:2020/Amd 1:2022 石油测量系统.校准.容积测量 试验箱和现场测量（包括液体和材料特性公式）.修改件1:两个印刷错误的校正

Petroleum measurement systems — Calibration — Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) — Amendment 1: Correction of two typogr

ASTM D7945-21a 用恒压粘度计测定液体动态粘度和衍生运动粘度的标准试验方法

1.1 This test method covers the measurement of dynamic viscosity and density for the purpose of derivation of kinematic viscosity of petroleum liquids, both transparent and opaque. The kinematic viscosity, ν, in this test method is derived by dividing the dynamic viscosity, η, by the density, ρ, obtained at the same test temperature. This test method also calculates the temperature at which petroleum liquids attain a specified kinematic viscosity using Practice D341. 1.2 The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rate are proportional (Newtonian flow behavior). 1.3 The range of kinematic viscosity covered by this test method is from 0.5 mm2 /s to 1000 mm2 /s in the temperature range between –40 °C to 120 °C; however the precision has been determined only for fuels and oils in the range of

Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer

KS B OIMLR 85-2021 自动液位计用于测量固定储罐中的液位

Automatic level gauges for measuring the level of liquid in fixed storage tanks

OENORM EN ISO 8222/A1:2021 石油测量系统 校准 体积测量、检验罐和现场测量（包括液体和材料特性的公式） 两个印刷错误的更正（ISO 8222:2020/DAM 1:2021）（修正案）

Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) - Correction of two typographical errors (ISO 8222:2020/DAM 1:2021) (Amendment)

ASTM F2059-21 用旋转瓶测定实验室溢油分散剂有效性的标准试验方法

1.1?This test method covers the procedure to determine the effectiveness of oil spill dispersants on various oils in the laboratory. This test method is not applicable to other chemical agents nor to the use of such products or dispersants in open waters. 1.2?This test method c

Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Swirling Flask

GSO ISO 6578:2021 冷冻碳氢化合物液体静态测量计算程序

ISO 6578:2017 specifies the calculation procedure to convert the volume of liquefied petroleum gas (LPG) and liquefied natural gas (LNG) under the conditions at the time of measurement to the equivalent volume of liquid or vapour at the standard condition, i.e. 15 °C and 101,325 kPaA, or to the equivalent mass or energy (calorific content). It applies to the quantities of refrigerated hydrocarbon liquids stored in or transferred to/from tanks and measured under static storage conditions. Calculation of pressurized gases is out of the scope of ISO 6578:2017.

Refrigerated hydrocarbon liquids — Static measurement — Calculation procedure