75.180.30 容积设备和容积测量 标准查询与下载

ISO 91:2017 石油及相关产品. 温度和压力容积校正因子(石油计量表)和标准基准条件

Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions

ASTM F2059-17 使用旋转瓶的实验室溢油分散剂有效性的标准测试方法

1.1 This test method covers the procedure to determine the effectiveness of oil spill dispersants on various oils in the laboratory. This test method is not applicable to other chemical agents nor to the use of such products or dispersants in open waters. 1.2 This test method covers the use of the swirling flask test apparatus and does not cover other apparatuses nor are the analytical procedures described in this report directly applicable to such procedures. 1.3 The test results obtained using this test method are intended to provide baseline effectiveness values used to compare dispersants and oil types under conditions analogous to those used in the test. 1.4 The test results obtained using this test method are effectiveness values that should be cited as test values derived from this standard test. Dispersant effectiveness values do not directly relate to effectiveness at sea or in other apparatuses. Actual effectiveness at sea is dependant on sea energy, oil state, temperature, salinity, actual dispersant dosage, and amount of dispersant that enters the oil. 1.5 The decision to use or not use a dispersant on an oil should not be based solely on this or any other laboratory test method. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Swirling Flask

BS ISO 12917-1:2017 石油和液化石油产品.卧式圆桶罐的校验.手工方法

Petroleum and liquid petroleum products. Calibration of horizontal cylindrical tanks. Manual methods

ISO 12917-1:2017 石油和液化石油产品.卧式圆形油罐的校正.第1部分:手工法

Petroleum and liquid petroleum products - Calibration of horizontal cylindrical tanks - Part 1: Manual methods

GOST R ISO 18132.1-2017 天然气液化. 罐储自动计量的通用要求. 第1部分. 海上运输船和浮仓的液化天然气储罐自动计量

Natural gas liquefied. General requirements for automatic tank gauges. Part 1. Automatic tank gauges for liquefied natural gas on board marine carriers and floating storage

GSO ASTM D6470:2016 原油中盐的标准测试方法（电位法）

1.1 This test method covers the determination of salt in crude oils. For the purpose of this test method, salt is expressed as % (m/m) NaCl (sodium chloride) and covers the range from 0.0005 % to 0.15 % (m/m). 1.2 The limit of detection is 0.0002 % (m/m) for salt (as NaCl). 1.3 The test method is applicable to nearly all of the heavier petroleum products, such as crude oils, residues, and fuel oils. It may also be applied to used turbine oil and marine diesel fuel to estimate seawater contamination. Water extractable salts, originating from additives present in oils, are codetermined. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Salt in Crude Oils (Potentiometric Method)

SY/T 6659-2016 用科里奥利质量流量计测量天然气流量

Measuring natural gas flow with a Coriolis mass flow meter

BS ISO 29945:2016 冷藏的基于非石油的液化气体燃料.二甲醚(DME).陆上终端的手动抽样方法

Refrigerated non-petroleum based liquefied gaseous fuels. Dimethylether (DME). Method of manual sampling onshore terminals

ISO 29945:2016 冷冻非石油基液化气体燃料. 二甲基乙醚(DME). 陆上终端的手动取样方法

This document specifies a manual sampling method for refrigerated liquefied DME at terminals in both loading and unloading ports along with precautions. This document does not include recommendations for the location of a sampling point in a line or vessel. This document is also applicable to the following cases, with necessary modifications: — sampling of DME on board liquefied gas tankers where appropriate sampling apparatus is provided; — sampling of other refrigerated, non-petroleum-based, liquefied gaseous fuels whose chemical and physical properties are similar to those of DME. The detailed chemical and physical properties of DME differ from those of LPG, which suggests that DME requires precautions different from those of LPG. However, their basic properties are similar to each other and so general reference is made in this document to precautions for LPG that have been applied in many countries. Reference can also be made to the appropriate individual items in this document for precautions concerning the quality.

Refrigerated non-petroleum based liquefied gaseous fuels - Dimethylether (DME) - Method of manual sampling onshore terminals

DIN EN 1776:2016 天然气基础设施.天然气测量系统.功能要求.德文版本EN 1776-2015

Gas infrastructure - Gas measuring systems - Functional requirements; German version EN 1776:2015

BS EN 1776:2015 天然气基础设施 气体测量系统 功能要求

Gas infrastructure. Gas measuring systems. Functional requirements

BS ISO 10976:2015 冷冻轻质烃流体 液化天然气运输船上货物的测量

Refrigerated light hydrocarbon fluids. Measurement of cargoes on board LNG carriers

DB35/T 1538-2015 天然气用超声流量计远程在线诊断及检验方法

本标准规定了安装在天然气管道上的超声流量计远程在线诊断和远程在线检验方法。 本标准适用于天然气用超声流量计的远程在线诊断及检验。

Remote on-line diagnosis and inspection method of ultrasonic flowmeter for natural gas

GSO 2497:2015 石油和天然气行业 使用喷嘴流量计进行气体测量

This specification defines the minimum requirements for orifice meters to be used for the custody transfer measurement of sales gas and ethane. This specification also defines the minimum requirements for the upstream and downstream meter tubes if they are supplied along with the orifice meter by the meter manufacturer or vendor.

Petroleum and natural gas industries- Orifice Meter for Gas Custody Measurement

GSO 2498:2015 石油和天然气行业 使用超声波示波器进行气体测量

This specification defines the minimum requirements for multi-path ultrasonic transit-time flow meters to be used for custody metering of sales gas and ethane. This specification also defines the minimum requirements for the upstream and downstream meter tubes, and associated components if they are supplied along with the ultrasonic meter by the meter manufacturer or vendor.

Petroleum and natural gas industries - Ultrasonic Flow Meter for Gas Custody Measurement

GSO ISO 16384:2015 低温碳氢化合物和非石油液化气燃料 二甲醚（DME） 机载测量和计算

  Scope is not provided for this standard

Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels -- Dimethylether (DME) -- Measurement and calculation on board ships

GSO 2496:2015 石油和天然气行业 多级流量计

1.1 This GSO standard defines the minimum requirements for engineering, design, fabrication and testing of Multi-Phase Flow Meters (MPFM) with its associated components for all fields and facilities. 1.2 This entire standard may be attached to and made a part of purchase orders.

Petroleum and natural gas industries - Multi-Phase Flow Meters

GSO ISO 15169:2015 石油和液体石油产品 混合储罐测量系统测定立式圆柱形储罐碳氢化合物含量的体积、密度和质量

  Scope is not provided for this standard

Petroleum and liquid petroleum products -- Determination of volume, density and mass of the hydrocarbon content of vertical cylindrical tanks by hybrid tank measurement systems

GSO ISO 18132-1:2015 低温轻烃液体 自动液位计的一般要求 第1部分：运载液化气体的船上液位计

ISO 18132-1:2011 establishes general principles for the accuracy, installation, calibration and verification of automatic tank gauges (ATGs) used for custody transfer measurement of liquefied natural gas (LNG) on board an LNG carrier or floating storage. The LNG described in ISO 18132-1:2011 is either fully refrigerated (i.e. at the cryogenic condition), or partially refrigerated, and therefore the fluid is at or near atmospheric pressure. ISO 18132-1:2011 also specifies the technical requirements for data collection, transmission and reception. Specific technical requirements for various automatic tank gauges and accuracy limitations are given in the annexes.

Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels -- General requirements for automatic tank gauges -- Part 1: Automatic tank gauges for liquefied natural gas on board marine carriers and floating storage

EN 1776:2015 天然气基础设施.气体测量系统.功能要求

This European Standard specifies functional requirements for the design, construction, testing, commissioning/decommissioning, operation, maintenance and, where appropriate, calibration, together with suitable documented provisions for all new gas measuring systems and any major changes of existing systems. This European Standard also specifies accuracy classes of measuring systems and thresholds applicable to these classes. Demonstration of compliance is achieved through the selection, installation and operation of appropriate measurement instruments, together with suitable documented provisions for calculations. Examples of demonstration of compliance are provided for each accuracy class; however, they are not prescriptive solutions. This European Standard is applicable to gases of the 2nd family as classified in EN 437. It is also applicable to treated non-conventional combustible gases complying with EN 437 and for which a detailed technical evaluation of the functional requirements (such as injected biomethane) is performed ensuring there are no other constituents or properties of the gases that can affect the metrological and physical integrity of the measuring systems. This European Standard can also be used as a guideline for 1st and 3rd family gases as classified in EN 437; however additional considerations should be taken with regard to the different constituents and physical characteristics of the gas family. This European Standard is not applicable to raw or sour gases. This European Standard is not applicable to gas measurement in CNG filling station. This European Standard gives guidelines when designing, installing and operating gas meters with additional functionalities (smart gas meters). Communication protocols and interfaces for gas meters and remote reading of gas meters are outside the scope of this European Standard and are covered by the appropriate parts of EN 13757, which provide a number of protocols for meter communications. Supervisory control and data acquisition protocols (SCADA) are also not covered by this European Standard. Unless otherwise specified all pressures used in this European Standard are gauge pressures. For associated pressure regulating systems the requirements of EN 12186 and/or EN 12279 apply. For requirements on design, housing, lay-out, materials for components, construction, ventilation, venting and overall safety of gas measuring systems within the scope of this European Standard, EN 15001, EN 12186, EN 12279 and/or EN 1775 apply additionally, where relevant. This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or codes of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned basic principles. In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, national legislation/regulation takes precedence.

Gas infrastructure - Gas measuring systems - Functional requirements