77.120.40 镍、铬及其合金 标准查询与下载

YS/T 252.6-2020 高镍锍化学分析方法 第6部分：铅、锌和砷含量的测定 电感耦合等离子体原子发射光谱法

Methods for chemical analysis of high nickel matte part 6: Determination of lead, zinc and arsenic content by inductively coupled plasma atomic emission spectrometry

ASTM B710-20 镍 - 铁 - 铬 - 硅合金焊接管的标准规范

Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe

ASTM B719-20 镍铬钼钴钨铁硅合金棒标准规范

1.1 This specification covers wrought alloy UNS N06333 in the form of hot-finished and cold-finished bars and flats intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy Bar

20/30408871 DC BS ISO 11433 镍合金 钛含量的测定 二安替比林甲烷分子吸收法

BS ISO 11433. Nickel alloys. Determination of titanium content. Diantipyrylmethane molecular absorption method

ASTM A481-05(2020) 铬金属标准规格

1.1 This specification covers several grades of chromium metal. 1.2 The values stated in inch-pound units are to be regarded as the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chromium Metal

ASTM E2594-20 用电感耦合等离子体原子发射光谱法分析镍合金的标准试验方法（基于性能）

1.1 This test method describes the inductively coupled plasma atomic emission spectrometric analysis of nickel alloys, such as specified by Committee B02, and having chemical compositions within the following limits: Element Application Range (%) Aluminum 0.01–1.00 Boron 0.001–0.050 Calcium 0.001–0.05 Carbon 0.10–0.20 Chromium 0.01–33.0 Cobalt 0.10–20.0 Copper 0.01–3.00 Iron 0.01–50.0 Lead 0.001–0.01 Magnesium 0.0001–0.100 Manganese 0.01–3.0 Molybdenum 0.01–30.0 Niobium 0.01–6.0 Nickel 25.0–80.0 Nitrogen 0.001–0.20 Oxygen 0.0001–0.003 Phosphorous 0.001–0.030 Sulfur 0.0001–0.010 Silicon 0.01–1.50 Tantalum 0.005–0.10 Tin 0.001–0.020 Titanium 0.001–6.0 Tungsten 0.01–5.0 Vanadium 0.01–1.0 Zirconium 0.01–0.10 1.2 The following elements may be determined using this test method. The test method user should carefully evaluate the precision and bias statements of this test method to determine applicability of the test method for the intended use. Element Quantification Range (%) Aluminum 0.060–1.40 Boron 0.002–0.020 Element Quantification Range (%) Calcium 0.001–0.003 Copper 0.010–0.52 Magnesium 0.001–0.10 Manganese 0.002–0.65 Niobium 0.020–5.5 Phosphorous 0.004–0.030 Tantalum 0.010–0.050 Tin 0.002–0.018 Titanium 0.020–3.1 Tungsten 0.007–0.11 Vanadium 0.010–0.50 Zirconium 0.002–0.10 1.3 This test method has only been interlaboratory tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different quantification ranges provided that method validation is performed that includes evaluation of method sensitivity, precision, and bias as described in this document. Additionally, the validation study must evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. The user is cautioned to carefully evaluate the validation data against the laboratory’s data quality objectives. Method validation of scope extensions is also a requirement of ISO/ IEC 17025. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 8.2.6.3 and safety hazard statements are given in Section 9. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee E01 on Analytical Chemistry for Metals, Ores, and Related Materials and is the direct responsibility of Subcommittee E01.08 on Ni and Co and High Temperature Alloys. Current edition approved Jan. 1, 2020. Published February 2020. Originally approved in 2009. Last previous edition approved in 2014 as E2594–09(2014). DOI: 10.1520/E2594-20. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 2. Referenced Documents

Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based)

ASTM E353-19e1 不锈钢、耐热、马氏体时效和其他类似铬镍铁合金化学分析的标准试验方法

1.1 These test methods cover the chemical analysis of stainless, heat-resisting, maraging, and other similar chromium-nickel-iron alloys having chemical compositions within the following limits: Element Composition Range, % Aluminum 0.002 to 5.50 Boron 0.001 to 0.20 Carbon 0.01 to 1.50 Chromium 0.01 to 35.00 Cobalt 0.01 to 15.00 Niobium 0.01 to 4.00 Copper 0.01 to 5.00 Lead 0.001 to 0.50 Manganese 0.01 to 20.00 Molybdenum 0.01 to 7.00 Nickel 0.01 to 48.00 Nitrogen 0.001 to 0.50 Phosphorus 0.002 to 0.35 Selenium 0.01 to 0.50 Silicon 0.01 to 4.00 Sulfur 0.002 to 0.50 Tantalum 0.01 to 0.80 Tin 0.001 to 0.05 Titanium 0.01 to 4.50 Tungsten 0.01 to 4.50 Vanadium 0.005 to 1.00 Zirconium 0.001 to 0.20 1.2 The test methods in this standard are contained in the sections indicated below: Sections Aluminum, Total, by the 8-Quinolinol Gravimetric Method (0.20 % to 7.00 %) 119–126 Aluminum, Total, by the 8-Quinolinol Spectrophotometric Method (0.003 % to 0.20 %) 71–81 Carbon, Total, by the Combustion–Thermal Conductivity Method–Discontinued 1986 153–163 Carbon, Total, by the Combustion Gravimetric Method (0.05 % to 1.50 %)–Discontinued 2013 98–108 Chromium by the Atomic Absorption Spectrometry Method (0.006 % to 1.00 %) 202–211 Sections Chromium by the Peroxydisulfate Oxidation–Titration Method (0.10 % to 35.00 %) 212–220 Chromium by the Peroxydisulfate-Oxidation Titrimetric Method-Discontinued 1980 145–152 Cobalt by the Ion-Exchange–Potentiometric Titration Method (2 % to 15 %) 53–60 Cobalt by the Nitroso-R-Salt Spectrophotometric Method (0.01 % to 5.0 %) 61–70 Copper by the Neocuproine Spectrophotometric Method (0.01 % to 5.00) %) 109–118 Copper by the Sulfide Precipitation-Electrodeposition Gravimetric Method (0.01 % to 5.00 %) 82–89 Lead by the Ion-Exchange-Atomic Absorption Spectrometry Method (0.001 % to 0.50 %) 127–136 Manganese by the Periodate Spectrophotometric Method (0.01 % to 5.00 %) 9–18 Molybdenum by the Ion Exchange–8-Hydroxyquinoline Gravimetric Method 242–249 Molybdenum by the Thiocyanate Spectrophotometric Method (0.01 % to 1.50 %) 190–201 Nickel by the Dimethylglyoxime Gravimetric Method (0.1 % to 48.0 %) 172–179 Phosphorus by the Alkalimetric Method (0.02 % to 0.35 %) 164–171 Phosphorus by the Molybdenum Blue Spectrophotometric Method (0.002 % to 0.35 %) 19–30 Silicon by the Gravimetric Method (0.05 % to 4.00 %) 46–52 Sulfur by the Gravimetric Method-Discontinued 1988 30–36 Sulfur by the Combustion-Iodate Titration Method (0.005 % to 0.5 %)-Discontinued 2014 37–45 Sulfur by the Chromatographic Gravimetric MethodDiscontinued 1980 137–144 Tin by the Solvent Extraction–Atomic Absorption Spectrometry Method (0.002 % to 0.10 %) 180–189 Tin by the Sulfide Precipitation-Iodometric Titration Method (0.01 % to 0.05 %) 90–97 Titanium by the Diantipyrylmethane Spectrophotometric Method (0.01 % to 0.35 %) 231–241 Vanadium by the Atomic Absorption Spectrometry Method (0.006 % to 0.15 %) 221–230 1.3 Test methods for the determination of carbon and sulfur not included in this standard can be found in Test Methods E1019. 1.4 Some of the composition ranges given in 1.1 are too broad to be covered by a single test method and therefore this standard contains multiple test methods for some elements. The user must select the proper test method by matching the information given in the Scope and Interference sections of each method with the composition of the alloy to be analyzed. 1 These test methods are under the jurisdiction of ASTM Committee E01 on Analytical Chemistry for Metals, Ores, and Related Materials and are the direct responsibility of Subcommittee E01.01 on Iron, Steel, and Ferroalloys. Current edition approved Nov. 15, 2019. Published February 2020. Originally approved in 1968. Last previous edition approved in 2014 as E353–14. DOI: 10.1520/E0353-19E01. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 6 and in special “Warning” paragraphs throughout these test methods. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys

ASTM E353-19 不锈钢 耐热 马氏体和其他类似铬 - 镍 - 铁合金化学分析的标准试验方法

Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys

ASTM B704-19 焊接镍合金管的标准规范

1.1 This specification covers welded UNS N06219, UNS N06625, UNS N08825, and UNS N08827 nickel alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service. 1.2 This specification covers tubes 1⁄8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Specification B751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Nickel Alloy Tubes

ASTM B729-19 无缝镍铁铬钼铜镍合金管规范

Standard Specification for Seamless Nickel-Iron-Chromium-Molybdenum-Copper Nickel Alloy Pipe and Tube

KS D 8302-2019 镍、铬电镀层

Electroplated coatings of nickel and chromium

ASTM B160-05(2019) 镍棒和镍棒的标准规范

1.1 This specification2 covers nickel (UNS N02200),3 lowcarbon nickel (UNS N02201),3 and solution-strengthened nickel (UNS N02211) in the form of hot-worked and coldworked rod and bar in the conditions shown in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel Rod and Bar

ASTM B78-90(2019) 电加热用铁铬铝合金加速寿命的标准试验方法

1.1 This test method covers the determination of the resistance to oxidation of iron-chromium-aluminum electrical heating alloys at elevated temperatures under intermittent heating using a constant-temperature cycle test. This test is used for internal comparative purposes only. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method of Accelerated Life of Iron-Chromium-Aluminum Alloys for Electrical Heating

KS D ISO TS 18223:2018 镍合金 - 镍含量的测定 - 电感耦合等离子体原子发射光谱法

Nickel alloys — Determination of Nickel content — Inductively coupled plasma atomic emission spectrometric method

KS D ISO TS 18223-2018 镍合金 - 镍含量的测定 - 电感耦合等离子体原子发射光谱法

Nickel alloys — Determination of Nickel content — Inductively coupled plasma atomic emission spectrometric method

ISO 23166:2018 镍合金化学分析方法电感耦合等离子体发射光谱法测定钽

This document specifies an inductively coupled plasma optical emission spectrometric method for the determination of tantalum contents between 0,1 % and 5 % in nickel alloys.

Nickel alloys — Determination of tantalum — Inductively coupled plasma optical emission spectrometric method

ASTM E1834-18 用石墨炉原子吸收光谱法分析镍合金的标准试验方法

1.1 This test method describes the graphite furnace atomic absorption spectrometric analysis of nickel, such as specified by ASTM Committee B02, and having chemical compositions within the following limits: Element Application Range (Mass Fraction %) Aluminum 0. 01 6.00 Boron 0. 01 0.10 Carbon 0. 01 0.15 Chromium 0. 01 33.00 Copper 0.01 35.00 Cobalt 0. 01 20.00 Iron 0.05 50.00 Magnesium 0. 01 0.020 Molybdenum 0. 01 30.0 Niobium 0. 01 6.0 Nickel 25.00 100.0 Phosphorous 0.001 0.025 Silicon 0.01 1.50 Sulfur 0.0001 0.01 Titanium 0.0001 6.0 Tungsten 0.01 5.0 Vanadium 0.0005 1.0 1.2 The following elements may be determined using this test method: Element Quantification Range (µg/g) Bismuth 0.2 3 Lead 0.6 12 Selenium 0.7 10 Tellurium 0.4 6 1.3 This test method has only been interlaboratory-tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different concentration ranges provided that a test method validation study that includes an instrument performance evaluation as described in Practice E1770 is performed. Additionally, the validation study shall evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. The user is cautioned to carefully evaluate the validation data as to the intended purpose of the analytical results. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 8.2.4.2 and 9. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry

KS D ISO TR 11434-2018 镍合金 镍合金中铌和钽的测定 离子交换法

Nickel alloys－Determination of niobium and tantalum in nickel alloys－Ion exchange method

ASTM B730-08(2018) 焊接镍（UNS N02200/UNS N02201）和镍铜合金（UNS N04400）管的标准规格

1.1 This specification covers nickel (UNS N02200), lowcarbon nickel (UNS N02201), and nickel copper alloy (UNS N04400) in the form of welded and annealed or welded and stress-relieved tube intended for general corrosive service and for mechanical applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Tube

ASTM B39-79(2018) 镍标准规格

1.1 This specification covers refined nickel primarily produced from ore or matte or similar raw material. The principal commercial forms are cathodes, briquettes, and pellets. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel