77.120.50 钛和钛合金 标准查询与下载

23/30454115 DC BS ISO 13093 钛和钛合金 碳的测定 感应炉燃烧后红外线吸收法

BS ISO 13093. Titanium and titanium alloys. Determination of carbon. Infrared absorption method after combustion in an induction furnace

KS D 2538-2022 钛合金.硫的测定方法

Titanium alloys — Methods for determination of sulfur

BS ISO 21334:2022 钛及钛合金 焊管用带材 交货技术条件

1   Scope This document specifies general requirements for the manufacture and technical delivery conditions of strips made from titanium and titanium alloys for welded tubes.

Titanium and titanium alloys — Strip for welded tubes — Technical delivery conditions

ISO 21334:2022 钛和钛合金.焊接管用带材.交货技术条件

This document specifies general requirements for the manufacture and technical delivery conditions of strips made from titanium and titanium alloys for welded tubes.

Titanium and titanium alloys — Strip for welded tubes — Technical delivery conditions

ASTM E1447-22 用热导率或红外光谱法检测的惰性气体熔融法测定活性金属和活性金属合金中氢的标准试验方法

1.1 This test method applies to the determination of hydrogen in reactive metals and reactive metal alloys, particularly titanium and zirconium, with mass fractions from 9 mg ⁄kg to 320 mg ⁄kg. 1.2 This method has been interlaboratory tested for titanium and zirconium and alloys of these metals and can provide quantitative results in the range specified in 1.1. It may be possible to extend the quantitative range of this method provided a method validation study, as described in Guide E2857, is performed and the results of the study show the method extension meets laboratory data quality objectives. This method may also be extended to alloys other than titanium and zirconium provided a method validation study, as described in Guide E2857, is performed. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards, see Section 9. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Hydrogen in Reactive Metals and Reactive Metal Alloys by Inert Gas Fusion with Detection by Thermal Conductivity or Infrared Spectrometry

BS ISO 23515:2022 钛及钛合金 指定系统

1   Scope This document specifies a designation system of titanium and titanium alloys in terms of their chemical composition and impurities contents.

Titanium and titanium alloys. Designation system

ISO 23515:2022 钛和钛合金.命名系统

This document specifies a designation system of titanium and titanium alloys in terms of their chemical composition and impurities contents.

Titanium and titanium alloys — Designation system

HB 7716.18-2022 钛合金化学成分光谱分析方法 第18部分：电感耦合等离子体原子发射光谱法测定锂、铅含量

Spectrometric analysis of titanium alloys – Part 18：Determination of lithium, lead content –Inductively coupled plasma atomic emission spectrometric method

HB 7716.15-2022 钛合金化学成分光谱分析方法 第15部分：电感耦合等离子体原子发射光谱法测定钨、铌、钽、镍含量

Spectrometric analysis of titanium alloys – Part 15：Determination of tungsten, niobium, tantalum, nickel content –Inductively coupled plasma atomic emission spectrometric method

HB 7716.16-2022 钛合金化学成分光谱分析方法 第16部分：电感耦合等离子体原子发射光谱法测定铂、钯含量

Spectrometric analysis of titanium alloys – Part 16：Determination of platinum, palladium content –Inductively coupled plasma atomic emission spectrometric method

YS/T 1465-2021 钛及钛合金加工产品外观缺陷术语及图谱

Terminology and diagram of appearance defects of titanium and titanium alloy processed products

ASTM E2994-21 用火花原子发射光谱法和辉光放电原子发射光谱法分析钛和钛合金的标准试验方法（基于性能的方法）

1.1 This test method describes the analysis of titanium and its alloys by spark atomic emission spectrometry (Spark-AES) and glow discharge atomic emission spectrometry (GD-AES). The titanium specimen to be analyzed may be in the form of a disk, casting, foil, sheet, plate, extrusion, or some other wrought form or shape. The elements and ranges covered in the scope by spark-AES of this test method are listed below. Element Tested Mass Fraction Range (%) Aluminum 0.008 to 7.0 Chromium 0.006 to 0.1 Copper 0.014 to 0.1 Iron 0.043 to 0.3 Manganese 0.005 to 0.1 Molybdenum 0.014 to 0.1 Nickel 0.006 to 0.1 Silicon 0.018 to 0.1 Tin 0.02 to 0.1 Vanadium 0.015 to 5.0 Zirconium 0.013 to 0.1 1.1.1 The elements oxygen, nitrogen, carbon, niobium, boron, yttrium, palladium, and ruthenium, were included in the ILS but the data did not contain the required six laboratories. Precision tables were provided for informational use only. 1.2 The elements and ranges covered in the scope by GD-AES of this test method are listed below. Element Tested Mass Fraction Range (%) Aluminum 0.02 to 7.0 Carbon 0.02 to 0.1 Chromium 0.006 to 0.1 Copper 0.028 to 0.1 Element Tested Mass Fraction Range (%) Iron 0.09 to 0.3 Molybdenum 0.016 to 0.1 Nickel 0.006 to 0.1 Silicon 0.018 to 0.1 Tin 0.022 to 0.1 Vanadium 0.054 to 5.0 Zirconium 0.026 to 0.1 1.2.1 The elements boron, manganese, oxygen, nitrogen, niobium, yttrium, palladium, and ruthenium were included in the ILS, but the data did not contain the required six laboratories. Precision tables were provided for informational use only. 1.3 The elements and mass fractions given in the above scope tables are the ranges validated through the interlaboratory study. However, it is known that the techniques used in this standard allow the useable range, for the elements listed, to be extended higher or lower based on individual instrument capability, available reference materials, laboratory capabilities, and the spectral characteristics of the specific element wavelength being used. It is also acceptable to analyze elements not listed in 1.1 or 1.2 and still meet compliance to this standard test method. Laboratories must provide sufficient evidence of method validation when extending the analytical range or when analyzing elements not reported in Section 18 (Precision and Bias), as described in Guide E2857. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety hazard statements are given in Section 9. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee E01 on Analytical Chemistry for Metals, Ores, and Related Materials and is the direct responsibility of Subcommittee E01.06 on Ti, Zr, W, Mo, Ta, Nb, Hf, Re. Current edition approved Dec. 1, 2021. Published January 2022. Originally approved in 2016. Last previous edition approved in 2016 as E2994 – 16. DOI: 10.1520/E2994-21. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 8QLYHUVLW\RI7RURQWR 8QLYHUVLW\RI7RURQWR SXUVXDQWWR/LFHQVH$JUHHPHQW1RIXUWKHUUHSURGXFWLRQVDXWKRUL]HG 'RZQORDGHGSULQWHGE\ &RS\ULJKWE\$670,QW O DOOULJKWVUHVHUYHG 6DW-DQ*07 2. Referenced Documents

Standard Test Method for Analysis of Titanium and Titanium Alloys by Spark Atomic Emission Spectrometry and Glow Discharge Atomic Emission Spectrometry (Performance-Based Method)

KS D 2532-2021 钛及钛合金中氢的测定方法

Methods for determination of hydrogen in titanium and titanium alloys

KS D 2530-2021 钛及钛合金中氮的测定方法

Methods for determination of nitrogen in titanium and titanium alloys

ASTM D6906-12a(2021) 用波长色散X射线荧光法测定金属基材上钛处理重量的标准试验方法

1.1 This test method covers the use of wavelength dispersive X-ray fluorescence (WDXRF) techniques for determination of the coating weight of titanium treatments on metal substrates. These techniques are applicable for determination of the coating weight as titanium or total coating weight of a titanium containing treatment, or both, on a variety of metal substrates. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Titanium Treatment Weight on Metal Substrates by Wavelength Dispersive X-Ray Fluorescence

ASTM F2924-14(2021) 粉末层熔合添加剂制造钛-6铝-4钒的标准规范

1.1 This specification covers additively manufactured titanium-6aluminum-4vanadium (Ti-6Al-4V) components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured Ti-6Al-4V components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more Supplementary Requirements, which may include, but are not limited to, those listed in S1-S16. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion

ASTM F3001-14(2021) 用粉末层熔合添加剂制造钛-6铝-4钒ELI（超低间隙）的标准规范

1.1 This specification covers additively manufactured titanium-6aluminum-4vanadium with extra low interstitials (Ti-6Al-4V ELI) components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers or both of additively manufactured Ti-6Al-4V ELI components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in S1-S4 and S1-S16 in Specification F2924. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion

KS D 2529-2021 钛及钛合金中碳的测定方法

Methods for determination of carbon in titanium and titanium alloys

T/CNIA 0084-2021 绿色设计产品评价技术规范 钛锭

本文件规定了钛锭绿色设计产品评价要求、生命周期评价报告编制方法及评价方法和流程。 本文件适用于以海绵钛及中间合金为原料，经真空自耗电弧熔炼或冷床炉熔炼生产的钛及钛合金铸锭（以下简称钛锭）的绿色设计产品评价。

Green Design Product Evaluation Technical Specification Titanium Ingot

ASTM E1409-13(2021) 用惰性气体熔合技术测定钛和钛合金中氧的标准试验方法

1.1 This test method covers the determination of oxygen in titanium and titanium alloys in mass fractions from 0.01 % to 0.5 % and the determination of nitrogen in titanium and titanium alloys in mass fractions from 0.003 % to 0.11 %. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 8.8. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Oxygen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique