77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

ISO 3444:2023 不锈钢钢丝绳

This document specifies requirements for manufacture, classification, test methods, packaging, marking and issuing of a certificate for stainless-steel wire ropes. It is applicable to stainless-steel wire ropes (hereafter referred to as ropes) for instruments, mechanical transmission, cable, sling, shock absorber vibration, yacht, architecture and structure.

Stainless-steel wire ropes

GSO ASTM A121:2023 金属涂层碳钢刺绳标准规范

This specification covers metallic-coated carbon steel barbed wire, consisting of a strand of two wires. The barbed wire is available with aluminum, zinc, and zinc-aluminum-mismatched alloy coatings with a number of coating weights. The barbed wire is classified as coating Type A, Type Z, and Type ZA. The sizes and constructions for barbed wire furnished under this specification shall conform the requirements. Sampling, testing and inspection of the material shall be performed in accordance with this specification.

Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

T/ZZB 2917-2022 热处理型冷镦钢丝

本文件规定了热处理型冷镦钢丝的分类及代号、 基本要求、 技术要求、试验方法、检验规则、包装、标识和运输储存、质量承诺。 本文件适用于公称直径1.00 mm～45.00 mm，用于制造铆钉、螺栓、螺钉和螺柱等紧固件及冷成型件制造用优质碳素结构钢丝和合金结构钢丝（以下简称钢丝）。紧固件或冷成型件经冷锻或冷挤压成型后，需要进行表面渗碳、渗氮、调质等热处理。

Cold heading and cold forging steel wire intended for heat treatment

T/ZZB 2946-2022 悬架用淬火-回火弹簧钢丝

本文件规定了悬架用淬火-回火弹簧钢丝的分类与代号、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于汽车悬架用淬火-回火弹簧钢丝（以下简称“钢丝”）。

Steel wire for quenched and tempered springs for suspensions

ASTM A392-11a(2022) 镀锌钢链环围栏织物标准规范

1.1 This specification covers zinc-coated steel chain-link fence fabric, zinc coated either before or after weaving. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

ASTM A824-01(2022) 与链环围栏一起使用的金属涂层钢马赛尔钢丝

1.1 This specification covers 0.177 in. (4.50 mm) diameter metallic-coated carbon steel marcelled tension wire for use with chain-link fence. The 0.177 in. (4.50 mm) diameter metallic-coated wire shall be produced in accordance with Specification A817. Three types of coatings are covered: 1.1.1 Type I—Aluminum-coated (aluminized), 1.1.2 Type II—Zinc-coated (galvanized), and 1.1.3 Type III—Zinc-5 % Aluminum Mischmetal (Zn5AlMM) alloy-coated. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence

ASTM F668-17(2022) 聚氯乙烯（PVC）、聚烯烃和其他聚合物涂层钢链围栏织物的标准规范

1.1 This specification covers polyvinyl chloride and other conforming organic polymer-coated steel chain-link fabric, coated before weaving. Polyvinyl chloride, polyolefin, and other organic polymer coating hereinafter will be designated as polymer coating. 1.2 Fabric produced from three classes of wire coatings are covered as follows: 1.2.1 Class I consists of polymer coatings extruded over zinc-coated, aluminum-coated, or zinc-5 % aluminummischmetal alloy-coated, or zinc-5 % aluminum-mischmetal alloy-coated steel wire. 1.2.2 Class 2a consists of polymer coating extruded and adhered to zinc-coated, aluminum-coated, or zinc-5 % aluminum-mischmetal alloy-coated steel wire. 1.2.3 Class 2b consists of polymer coating fused and adhered to zinc-coated, aluminum-coated, or zinc-5 % aluminum-mischmetal alloy-coated steel wire. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyvinyl Chloride (PVC), Polyolefin and Other Polymer-Coated Steel Chain Link Fence Fabric

ASTM A491-11(2022) 铝涂层钢链环围栏织物标准规范

1.1 This specification covers aluminum-coated steel chainlink fence fabric, aluminum-coated before weaving. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric

ASTM A581/A581M-22a 易加工不锈钢丝和线材标准规范

1.1 This specification covers free-machining stainless steels of cold-finished wire and hot-finished wire rods in coils. Wire rods are a semi-finished product primarily for the manufacture of wire. Wire includes rounds, squares, hexagons, and special shapes in free-machining stainless steels designed especially for optimum machinability and for general corrosion and high-temperature service. 1.2 The following alloys are covered: 1.2.1 Austenitic alloys: UNS numbers S20300, S30300, S30310, S30323, and S30345; 1.2.2 Martensitic alloys: UNS numbers S41600, S41610, and S41623; and 1.2.3 Ferritic alloys: UNS numbers S18200, S18235, S41603, S43020, and S43023. NOTE 1—For wire other than for free-machining applications, see Specification A580/A580M. NOTE 2—For Free-Machining Stainless Steel Bars, see Specification A582/A582M. 1.3 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inchpound units. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Free-Machining Stainless Steel Wire and Wire Rods

BS ISO 2232:2022 通用钢丝绳、大直径钢丝绳和矿井提升钢丝绳用非合金圆钢丝 规格

Round non-alloy steel wires for general purpose wire ropes, large diameter wire ropes and mine hoisting wire ropes. Specifications

ASTM B803/B803M-22 高强度锌的标准规范&x2013；5 ；%架空导线用铝-混合稀土合金涂层钢芯线

1.1 This specification covers round, high strength, zinc–5 % aluminum-mischmetal (Zn–5Al–MM) alloy-coated, steel core wire with one class of Zn–5Al–MM coating (MA3) for use in overhead electrical conductors. 1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

ASTM B957/B957M-22 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范

1.1 This specification covers round, extra-high-strength and ultra-high-strength, Class A zinc-coated (galvanized), steel core wire used for use in Overhead Electrical Conductors. 1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead Electrical Conductors

ASTM B958/B958M-22 架空导线用超高强度和超高强度A级锌-5%铝-混合合金涂层钢芯线

1.1 This specification covers round, extra-high-strength, and ultra-high-strength, Class A coated zinc–5 % aluminummischmetal (Zn–5Al–MM) alloy-coated, steel core wire for use in Overhead Electrical Conductors. 1.2 This specification covers wire of diameter from 0.0500 to 0.1900 in. inclusive or 1.27 to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

YB/T 4996-2022 索氏体化热处理碳素钢丝

本文件规定了索氏体化热处理碳素钢丝的术语和定义、分类及标记、订货内容、技术要求、检验和试验、验收方法、包装、标志、运输、贮存和质量证明书等。 本文件适用于碳含量0.32%~0.90%、直径0.80mm~16.00mm，经过铅液、盐液、水溶性有机物等淬火介质进行索氏体化热处理的碳素钢丝。 索氏体化热处理盘条可参照本文件执行。

Sorting heat treated carbon steel wire

YB/T 6031-2022 汽车发动机燃油导轨用不锈钢丝及棒

本文件规定了汽车发动机燃油导轨用不锈钢丝及棒的订货内容、尺寸、外形及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本文件适用于直径10.00 mm ～50.00 mm的汽车发动机燃油导轨用不锈钢丝及棒。

Stainless steel wire and rod for automobile engine fuel rail

YB/T 6030-2022 汽车掣动推拉索芯

本文件规定了汽车掣动推拉索芯的定义、分类和标记、订货内容、材料、技术要求、试验方法、检验规则、质量保证期、包装、贮存、运输及质量证明书。 本文件适用于汽车选换档掣动总成、刹车掣动总成用推拉索芯。工程机械、轨道交通、游艇、船舶、航空飞行器等其他控制总成用推拉索芯也可参照本文件执行。

Car brake push-pull cable core

YB/T 6079-2022 胎圈钢丝试验方法

本文件规定了胎圈用钢丝的试样一般规定、外观质量、尺寸、工艺性能、力学性能、镀层分析试验方法、粘合性能试验方法。 本文件适用于各类轮胎胎圈用回火圆形钢丝的试验方法。

Bead wire test method

YB/T 6032-2022 制簧用钢丝绳

本文件规定了制簧用钢丝绳的术语和定义、分类和标记、订货内容、材料、技术要求、检查与试验、检验规则、包装、标志及质量证明书。 本文件适用于汽车座靠垫、床垫、以及其他家具、室内装饰等弹簧用钢丝绳。

Wire rope for spring making

ASTM A581/A581M-22 高速切削用耐热不锈钢丝和盘条的标准规格

Standard Specification for Free-Machining Stainless Steel Wire and Wire Rods

ASTM A555/A555M-22 不锈钢丝和盘条一般要求的标准规范

1.1 This specification covers general requirements that shall apply to stainless wire and wire rods. Wire rods are a semifinished product intended primarily for the manufacture of wire. Wire is intended primarily for cold forming, including coiling, stranding, weaving, heading and machining as covered under the latest revision of each of the following ASTM specifications: A313/A313M, A368, A478, A492, A493, A580/A580M, and A581/A581M. 1.2 In case of conflicting requirements, the individual material specification and this general requirement specification shall prevail in the order named. 1.3 General requirements for flat products other than wire are covered in Specification A480/A480M. 1.4 General requirements for bar and billet products are covered in Specification A484/A484M. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 Unless the order specifies the applicable metric specification designation, the material shall be furnished in the inch-pound units. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods