型钢标准-分析测试百科网

YB/T 4620-2017 抗震热轧H型钢

Anti-seismic hot-rolled H-shaped steel

ICS: 77.140.70
CCS: H44
发布: 2017-07-07
实施: 2018-01-01

ASTM A769/A769M-17 碳和高强度电阻锻造焊接钢结构形状的标准规范

1.1 This specification covers carbon and high-strength steel shapes of structural quality manufactured by the electricresistance forge-welding process from coils. 1.2 The size range covered is described in nominal dimensions for columns, beams, and tees. Size Range, in. (mm) Web thickness 0.060 to 0.500 [1.5 to 12.7] Flange thickness 0.060 to 0.500 [1.5 to 12.7] Overall depth 2.00 to 24.00 [50 to 600] Flange width 0.50 to 12.00 [12.7 to 300] 1.3 These shapes are intended for two classes of application: 1.3.1 Class 1—General structural use where static loading predominates. 1.3.2 Class 2—Structural use where fatigue loading occurs and is a principal design consideration. NOTE 1—Caution—Because of the absence of smooth, integral, large radius fillets at the junctions of the webs and the flanges (see Fig. 1), fatigue limits of resistance forge-welded shapes in torsion, lateral loading, and flexure are usually lower than those for hot-rolled shapes of similar size and material. Users should consult shape manufacturers for recommended values of fatigue limits for each specific use, material, and size in cases where dynamic loading is a principal design consideration. 1.4 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 The following safety hazards caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Carbon and High-Strength Electric Resistance Forge-Welded Steel Structural Shapes

ICS: 77.140.70
CCS
发布: 2017-06-01
实施

DIN EN 10056-1:2017 结构钢制等边和不等边角钢.第1部分:尺寸;德文版本EN 10056-1-2017

Structural steel equal and unequal leg angles - Part 1: Dimensions; German version EN 10056-1:2017

ICS: 77.140.70
CCS: H44
发布: 2017-06
实施

DIN EN 10365:2017 I和H形热轧钢槽. 尺寸和质量; 德文版本EN 10365-2017

Hot rolled steel channels, I and H sections - Dimensions and masses; German version EN 10365:2017

ICS: 77.140.70
CCS
发布: 2017-05
实施

BS EN 10056-1:2017 等角和非等角结构钢.尺寸

Structural steel equal and unequal leg angles. Dimensions

ICS: 77.140.70
CCS: H40
发布: 2017-01-31
实施: 2017-01-31

BS EN 10365:2017 I和H形热轧钢槽. 尺寸和质量

Hot rolled steel channels, I and H sections. Dimensions and masses

ICS: 77.140.70
CCS: H44
发布: 2017-01-31
实施: 2017-01-31

EN 10365:2017 热轧槽钢，I 型和 H 型尺寸和质量

This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections. The following shapes are covered by this standard: Sections: - Parallel flange I sections IPE; - Wide flange beams HE; - Extra wide flange beams HL and HLZ; - Wide flange columns HD; - Wide flange bearing piles HP and UBP; - Universal beams UB; - Universal columns UC; - Taper flange I sections IPN and J. Channels; - Parallel flange channels UPE and PFC; - Taper flange channels UPN, U and CH. These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel.

Hot rolled steel channels, I and H sections - Dimensions and masses

ICS: 77.140.70
CCS: Q15
发布: 2017-01
实施

EN 10056-1:2017 结构钢制等边和不等边角钢.第1部分:尺寸

This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainless steel.

Structural steel equal and unequal leg angles - Part 1: Dimensions

ICS: 77.140.70
CCS: Q15
发布: 2017-01
实施

GOST R 58034-2017 非合金钢热轧薄板堆. 第1部分: 规格

Hot rolled sheet piling of non alloy steels. Part 1. Specifications

ICS: 77.140.70
CCS
发布: 2017-00-00
实施: 2020-01-01

GSO ISO 630-6:2016 结构钢第6部分：建筑用抗震改进结构钢交货技术条件

This part of ISO 630 specifies qualities for seismic-proof improved structural steels. This part of ISO 630 applies to steel plates with thicknesses of 6 mm or over and up to 125 mm, wide flats and hot-rolled sections up to 140 mm, which are used in the usual delivery conditions as given in 6.2 and normally intended for welded or bolted structures. This part of ISO 630 does not include the following structural steels, certain of which are covered by other International Standards: — sheet and strip – refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — tubular products – refer to ISO TC 5/SC 1, Steel tubes.

Structural steels -- Part 6: Technical delivery conditions for seismic-proof improved structural steels for building