77.150.40 镍和铬产品 标准查询与下载

YS/T 277-2016 氧化亚镍

Nickel oxide

ASTM B718-00(2016) 镍 - 铬 - 钼 - 钴 - 钨 - 铁 - 硅合金（UNS N06333）板 板和带的标准规范

1.1 This specification covers wrought alloy UNS N06333 plate, sheet, and strip intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Plate, Sheet, and Strip

ASTM B572-06(2016) 标准规范UNS N06002 UNS N06230 UNS N12160和UNS R30556棒

1.1 This specification2 covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R305563 in the form of rod for heat resisting and general-corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5⁄16 to 3⁄4 in. (7.94 to 19.05 mm) exclusive in diameter, hot or cold finished, solution-annealed, and pickled or mechanically descaled. 1.2.2 Rods 3⁄4 to 31⁄2 in. (19.05 to 88.9 mm) inclusive in diameter, hot or cold finished, solution annealed, ground, or turned. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod

GOST 2936-2016 平面椭圆无缝散热管. 规格

Planc-oval scamless radiator tubes. Specifications

ASTM B775/B775M-16 镍和镍合金焊接管通用要求的标准规格

1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2 Title of Specification ASTM Designation2   Welded UNS N08020 Alloy Pipe B464/B464M Welded Nickel-Iron-Chromium Alloy Pipe B514 Welded Nickel-Chromium-Iron-Alloy (UNS N06600, 8199;UNS N06603, UNS N06025 and UNS N06045) Pipe B517 Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673 UNS N08367 Welded Pipe B675 Nickel-Alloy (UNS N06625, N06219, and N08825) Welded 8199;Pipe B705 Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723 Welded Nickel (UNS N02200/UNS N02201) and Nickel 8199;Copper Alloy (UNS N04400) Pipe B725

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

GOST 15515-2016 镍电解条. 规格

Nickel electrolysis strips. Specifications

GOST 13083-2016 镍和镍硅合金棒. 规格

Rods of nickel and nickel-silicon alloys. Specifications

ASTM B511/B511M-16 镍铁铬硅合金棒材和型材的标准规格

1.1 This specification2 covers wrought alloys UNS N08330 and UNS N08332 in the form of hot-finished and cold-finished bar and shapes intended for heat-resisting applications and general corrosive service. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes

KS D 6721-2015 镍及镍合金线材和拉丝原料

Nickel and nickel alloy wire and drawing stock

NB/T 47046-2015 承压设备用镍及镍合金板

本标准规定了承压设备用镍及镍合金板的尺寸、外形、技术要求、试验方法、检验规则、包装、标志和质量证明书等。 本标准适用于制造承压设备用厚度为1mm～100mm的镍及镍合金板。

Nickel -nickel alloy plate for pressure equipments

NB/T 47047-2015 承压设备用镍及镍合金无缝管

本标准规定了承压设备用镍及镍合金无缝管的尺寸、外形、技术要求、试验方法、检验规则、包装、标志和质量证明书等。 本标准适用于制造承压设备用的镍及镍合金无缝管。

Nickel -nickel alloy seamless tube and pipe for pressure equipments

GSO ISO 6208:2015 镍板、带材、带材和镍合金

This International Standard specifies requirements for hot-rolled or cold-rolled nickel and nickel alloy plate, sheet and strip, for general applications in the following size ranges: — plate over 4 mm up to and including 100 mm; — sheet up to and including 4 mm; — strip up to and including 4 mm.

Nickel and nickel alloy plate, sheet and strip

YS/T 1087-2015 掺杂型镍钴锰三元素复合氢氧化物

本标准规定了掺杂型镍钴锰三元素复合氢氧化物的要求，试验方法，检验规则，标志、包装、运输、贮存和质量证明书及订货单(或合同)。 本标准适用于锂离子电池正极材料前驱体用掺杂型镍钴锰三元素复合氢氧化物。

Doped nickel cobalt manganese composite hydroxide

NB/T 20008.21-2015 压水堆核电厂用其他材料第21部分:控制棒驱动机构用GH4169合金棒

本部分规定了压水堆核电厂控制棒驱动机构用GH4169镍基合金棒的制造、检验和验收等要求。 本部分适用于压水堆核电厂控制棒驱动机构用直径小于或等于38 mm的GH4169镍基合金棒。

Other material for pressurized water reactor nuclear power plants.Part 21: GH4169 alloy bars used for CRDM

NB/T 20008.22-2015 压水堆核电厂用其他材料第22部分:控制棒驱动机构用GH4145合金棒

本部分规定了压水堆核电厂控制棒驱动机构用GH4145镍基合金棒的制造、检验和验收等要求。 本部分适用于压水堆核电厂控制棒驱动机构用直径为25 mm？50 mm的GH4145镍基合金棒。

Other material for pressurized water reactor nuclear power plants.Part 22: GH4145 alloy bars used for CRDM

ASTM B775-15 镍和镍合金焊接管通用要求的标准规格

1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2 Title of Specification ASTM Designation2   Welded UNS N08020, N08024, and N08026 Alloy Pipe B464/B464M Welded Nickel-Iron-Chromium Alloy Pipe B514 Welded Nickel-Chromium-Iron-Alloy (UNS N06600, 8199;UNS N06603, UNS N06025 and UNS N06045) Pipe B517 Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673 UNS N08367 Welded Pipe B675 Nickel-Alloy (UNS N06625, N06219, and N08825) Welded 8199;Pipe B705 Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723 Welded Nickel (UNS N02200/UNS N02201) and Nickel 8199;Copper Alloy (UNS N04400) Pipe B725

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

GOST 2179-2015 镍和硅酸镍丝. 规格

Nickel and siliceous nickel wire. Specifications

GOST 1049-2015 锰镍丝. 规格

Manganese nickel wire. Specifications

ASTM B574-15 低碳镍铬钼, 低碳镍钼铬, 低碳镍钼铬钽, 低碳镍铬钼铜以及低碳镍铬钼钨的标准规格

1.1 This specification2 covers rod of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059)*, low-carbon nickel-molybdenum-chromium (USN N10362), low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), low-carbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenum-tungsten (UNS N06686) as shown in Table 1, for use in general corrosive service. (A) See 12.1.1. (A) D refers to the diameter of the tension specimen. (A) D refers to the diameter of the tension specimen. 1.2 The following products are covered under this specification: 1.2.1 Rods 5/16 to 3/4 in. (7.94 to 19.05 mm), exclusive, in diameter, hot or cold finished, solution annealed and pickled, or mechanically descaled. 1.2.2 Rods 3/4 to 31/2 in. (19.05 to 88.9 mm), inclusive, in diameter, hot or cold finished, solution annealed, ground or turned. 1.2.3 Rods 1/4 to 3 1/2 in. (6.35 to 88.9 mm), inclusive, in diameter, solution annealed, cold finished, as cold finished, ground or turned (N06059 and N06686 only, see Table 2 and Table 3). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten

GOST 2132-2015 镍阳极. 规格

Nickel anodes. Specifications