77.150.40 镍和铬产品 标准查询与下载

T/ZZB 1912-2020 多层片式陶瓷电容器电极镍粉

本文件规定了多层片式陶瓷电容器电极镍粉（以下简称产品）的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存以及质量承诺。 本文件适用于多层片式陶瓷电容器内电极上使用的平均粒径为150 nm～400 nm 的镍粉，其他粒径的电极镍粉可参照本文件。

Nickel powder for electrode of multi-layer ceramic capacitor

ASTM B343-92a(2020) 用镍电镀镍的标准实践

1.1 This practice summarizes well-known, generally practical methods for producing adherent electrodeposits of nickel on nickel. 1.2 Electrodeposits of nickel on nickel are produced, for example, to improve the performance of decorative coatings, to reclaim electroplated parts that are defective, and to resume nickel electroplating after interruptions in processing. Interruptions may be deliberate, for example, to machine the electrodeposit at an intermediate stage in the electrodeposition of thick nickel coatings. The interruptions may be unintentional, for example, resulting from equipment and power failures. 1.3 To ensure good adhesion of nickel to nickel, precautions should be taken to avoid biopolar effects during nickel electroplating. This is of particular importance in return-type automatic plating machines where one rack follows another rack closely. Bipolar effects can be avoided by making the racks cathodic while they are entering or leaving the nickel tank. Separate current control on entry and exit stations is desirable. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Nickel for Electroplating with Nickel

ASTM B814-06(2020) 镍铬铁钼钨合金（UNS N06920）板材、薄板和带材的标准规范

1.1 This specification covers nickel-chromium-ironmolybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip—Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish; and 1.2.2 Plate—Hot rolled, solution-annealed, and descaled. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Iron-Molybdenum-Tungsten Alloy(UNS N06920) Plate, Sheet, and Strip

ASTM B344-20 用于电加热元件的拉制或轧制的镍 - 铬和镍 - 铬 - 铁合金的标准规范

1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating purposes, of alloys having the nominal compositions of 80 % nickel and 20 % chromium; 60 % nickel, 16 % chromium, and remainder iron; and 35 % nickel, 20 % chromium, and remainder iron; 38 % nickel, 21 % chromium, and remainder iron; and 35 % nickel, 20 % chromium remainder iron. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Drawn or Rolled Nickel-Chromium and Nickel-Chromium-Iron Alloys for Electrical Heating Elements

T/JSQA 026-2020 低温压力容器用镍合金钢板

        本标准规定了低温压力容器用镍合金钢板的订货内容，牌号表示方法，尺寸、外形、重量及允许偏差，技术要求，试验方法，检验规则，包装、标志及质量证明书等。本标准适用于制造-196℃～＜-20℃低温压力容器用厚度为5mm～100mm的镍合金钢板。

Nickel alloy steel plates for low temperature pressure vessels

ASTM B751-20 镍和镍合金焊接管一般要求的标准规范

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Tube

ASTM B599-20 镍铁铬钼铌稳定合金板、薄板和带材的标准规范

1.1 This specification covers nickel-iron-chromiummolybdenum-niobium stabilized alloy (UNS N08700)2 plate, sheet, and strip in the solution-annealed condition. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Niobium Stabilized Alloy Plate, Sheet, and Strip

ASTM B512-20 镍铬硅合金坯料和棒材的标准规范

1.1 This specification covers wrought heat-resisting alloy UNS N08330 in the form of billets and bars only for reforging. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Silicon Alloy Billets and Bars

T/CLCJH 001-2020 绿色设计产品评价技术规范 泡沫镍

本标准规定了泡沫镍的绿色设计产品的术语和定义、分类、要求、检验方法和指标计算方法、产品生命周期评价方法及评价报告编制方法、评价结论。本标准适用于泡沫镍的绿色设计产品评价。

Green Design Product Evaluation Technical Specifications for Nickel Foam

ASTM B425-19 镍铁铬钼铜合金棒

1.1 This specification2 covers nickel-iron-chromiummolybdenum-copper alloys (UNS N06845, UNS N08221, UNS N08825, and UNS N08827)3 in the form of hot-finished and cold-drawn rounds, squares, hexagons, and rectangles. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloys Rod and Bar

ASTM B443-19 镍铬钼铌合金和镍铬钼硅合金板、薄板和带材的标准规范

1.1 This specification2 covers rolled nickel-chromiummolybdenum-columbium alloy (UNS N06625) and nickelchromium-molybdenum-silicon alloy (UNS N06219)3 plate, sheet, and strip. 1.1.1 Alloy UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1 (Annealed)—Material is normally employed in service temperatures up to 1100°F (593°C). 1.1.1.2 Grade 2 (Solution Annealed)—Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required. NOTE 1—Hot-working or reannealing may change properties significantly, depending on working history and temperatures. 1.1.2 Alloy UNS N06219 is supplied in solution annealed condition only. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy and Nickel-Chromium-Molybdenum-Silicon Alloy Plate, Sheet, and Strip

ASTM B424-19e1 镍铁铬钼铜合金板、薄板和带材的标准规范

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloys Plate, Sheet, and Strip

ASTM B165-19 镍铜合金无缝管标准规范

1.1 This specification2 covers nickel-copper alloy UNS N044003 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1. 1.1.1 Hot worked material is available. Properties and permissible tolerances are to be agreed upon between the manufacturer and purchaser. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Copper Alloy Seamless Pipe and Tube

ASTM B424-19 镍铁铬钼铜合金板、薄板和带材的标准规范

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloys Plate, Sheet, and Strip

ASTM F2633-19 用于医疗器械和外科植入物的锻造无缝镍钛形状记忆合金管的标准规范

1.1 This specification covers the requirements for wrought nickel-titanium shape memory alloy tube, nominally 54.5 to 57.0 mass/mass (weight) % nickel, in the superelastic condition, used for the manufacture of medical devices and surgical implants. Material shall conform to the applicable requirements of Specification F2063. This specification addresses those product variables that differentiate drawn medical grade tube from the raw material and mill product forms covered in Specification F2063. 1.2 This specification applies to tube with 10 mm (0.4 in.) and smaller nominal outside diameter and 2 mm (0.08 in.) and thinner nominal wall thickness. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses (inch-pound units) are for information only. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wrought Seamless Nickel-Titanium Shape Memory Alloy Tube for Medical Devices and Surgical Implants

ASTM B564-19 镍合金锻件的标准规范

Standard Specification for Nickel Alloy Forgings

ASTM B599-19 镍铁铬钼铌稳定合金板、薄板和带材的标准规范

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy Plate, Sheet, and Strip

T/CNIA 0032-2019 粗制碳酸镍

本标准规定了钴镍原料经冶炼除杂后产出的粗制碳酸镍的技术要求、试验方法、检验规则、标志、标签、包装、运输、贮存和质量预报单、订货单（或合同）内容等。 本标准适用于粗制碳酸镍，本产品可作为生产工业碳酸镍、硫酸镍、催化剂原料、电镀液组份或制取其他含镍物的原料。

Crude Nickel Carbonate

YS/T 1338-2019 电容器电极镍粉

Capacitor electrode nickel powder

ASTM B168-19 镍铬铝合金（UNS N06699）、镍铬铁合金（UNS N06600、N06601、N06603、N06690、N06693、N06025、N06045和N06696）、镍铬钴钼合金（UNS N06617）、镍铁铬钨合金（UNS N06674）和镍铬钼铜合金（UNS N06235）板材、薄板、 剥去

Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Mo