81.040.20 建筑玻璃 标准查询与下载

JIS R 3106:2019 平板玻璃的透射率、反射率和发射率的测试方法及玻璃总太阳能透射率的计算

Testing method for transmittance, reflectance and emissivity of flat glass and calculation of total solar energy transmittance of glazing

JIS R 3107:2019 玻璃热传递系数的计算

Calculation of thermal transmittance of glazing

T/CBMF 45-2019 建筑用Low-E玻璃制品质量检验标准

本标准规定了建筑用Low-E玻璃制品的检验标准，包括术语和定义、分类、分级和标记、要求和检测。 本标准适用于安装之前和安装之后门窗和幕墙用Low-E成品玻璃的检验。

Quality inspection standard for Low-E glass products for construction

ASTM C1172-19 建筑用层压平板玻璃标准规范

1.1 This specification covers the quality requirements of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building and related applications. 1.2 Depending on the number, thickness, and treatment of lites, and the number and thickness of interlayers, the glass shall be laminated for applications including, but not limited to, safety, security, detention, hurricane/cyclic-wind resistance, blast resistance, bullet resistance, sound reduction, and decorative glazing. 1.3 Optical distortion and the evaluation thereof are not currently within the scope of the standard. Mockups are recommended as a method to evaluate glass. (See Appendix X1.) 1.4 The dimensional values, except thickness designations, stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Laminated Architectural Flat Glass

ASTM E2190-19 中空玻璃组件性能和评定的标准规范

1.1 This specification covers preassembled permanently sealed insulating glass units with one or two cavities and preassembled insulating glass (IG) units with capillary tubes intentionally left open or closed. 1.2 This specification is applicable only to insulating glass units that are constructed with glass or suspended film. 1.3 This specification is applicable to both double-glazed and triple-glazed insulating glass units; for triple-glazed insulating glass units where both of the outer lites are glass and middle lite is either glass or a suspended film. 1.4 The qualification of test specimens is based on frost/dew point and on the absence of fog after the specified test durations. 1.5 The qualification of argon gas-filled test specimens is based on maintaining the specified argon gas amounts before and after testing to Test Method E2188. 1.6 Qualification under this specification is intended to provide a basis for evaluating the durability of insulating glass units. 1.7 This specification is not applicable to insulating glass units containing a spandrel glass coating due to test method limitations. 1.8 This specification does not cover other physical requirements such as appearance, thermophysical properties, heat and light transmission, and glass displacement. NOTE 1—Insulating glass units qualified according to this specification are not necessarily suitable for structurally glazed applications. Factors such as sealant longevity when exposed to long term ultraviolet light and the structural properties of the sealant must be reviewed for these applications. For more information on the requirements for structural sealant glazing applications, refer to Specification C1369, Guide C1249, and Test Method C1265. 1.9 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Insulating Glass Unit Performance and Evaluation

ASTM D8040-18 玻璃器皿中传热液体腐蚀试验的标准试验方法

1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air conditioning (HVAC) systems. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

DIN EN 1096-4:2018 建筑玻璃 镀膜玻璃 第4部分：产品标准；德文版 EN 1096-4:2018

This European Standard covers the assessment and evaluation of constancy of performance (AVCP)of coated glass for use in buildings.

Glass in building - Coated glass - Part 4: Product standard; German version EN 1096-4:2018

BS ISO 19916-1:2018 建筑中的玻璃 真空中空玻璃 产品基本规格及隔热、隔音性能评价方法

What is this ISO 19916-1 - V acuum insulating glass about?    The use of glass in constructions delivers economic, environmental, and social objectives, all of which are central when defining sustainable buildings. In order to support a shift towards the design of genuinely sustainable buildings and ensure the quality of the glass and glazed products manufactures and uses, we have an extensive range of glass and glazing standards to help meet your construction needs.   ISO 19916 is series discusses standards for vacuum insulating g lass in building. ISO 19916-1 specifies product specification for vacuum insulating glass. It also specifies evaluation methods for thermal and sound insulating performance and evaluation methods for thermal insulation durability.

Glass in building. Vacuum insulating glass - Basic specification of products and evaluation methods for thermal and sound insulating performance

DIN EN 1279-5:2018 建筑玻璃 中空玻璃 第5部分：产品标准；德文版 EN 1279-5:2018

This document covers the product standard of insulating glass units (IGU) for use in buildings. Units for which the intended use is only artistic and therefore no essential characteristics are required are not subject to CE marking and are not part of this standard. For glass products with electrical wiring or connections for, e. g. alarm or heating purposes, other directives, e. g. Low Voltage Directive, may apply.

Glass in building - Insulating glass units - Part 5: Product standard; German version EN 1279-5:2018

DIN EN 1279-1:2018 建筑玻璃 中空玻璃单元 第1部分：概述、系统描述、替代规则、公差和视觉质量；德文版 EN 1279-1:2018

This document (all parts) covers the requirements for insulating glass units. The main intended uses of the insulating glass units are installations in windows, doors, curtain walling, bonded glazing for doors, windows and curtain walling, roofs and partitions. The achievement of the requirements of this standard indicates that insulating glass units fulfil the needs for intended use and ensures by means of the evaluation of conformity to this standard that, visual, energetic, acoustic, safety parameters do not change significantly over time. In cases where there is no protection against direct ultraviolet radiation or permanent shear load on the edge seal, as in bonded glazing for doors, windows and curtain walling systems, it is essential to follow additional European Technical Specifications (see EN 15434, EN 13022 1 and prEN 16759). Insulating glass units that are intended for artistic purposes (e. g. lead glass or fused glass) are excluded from the scope of this standard. Vacuum insulating glass is not covered by this standard (see ISO DIS 19916 1). Glass/plastics composites are under the scope as long as the surface of contact with sealants is a glass component. NOTE For glass products with electrical wiring or connections for, e. g. alarm or heating purposes, other directives, e. g. Low Voltage Directive, may apply. This European Standard gives definitions for insulating glass units and covers the rules for the system description, the optical and visual quality and the dimensional tolerances thereof and describes the substitution rules based on an existing system description.

Glass in Building - Insulating glass units - Part 1: Generalities, system description, rules for substitution, tolerances and visual quality; German version EN 1279-1:2018

ISO 19916-1:2018 建筑玻璃.真空中空玻璃.第1部分：隔热和隔音性能的产品基本规范和评价方法

This document specifies product specification for vacuum insulating glass. It also specifies evaluation methods for thermal and sound insulating performance and evaluation methods for thermal insulation durability.

Glass in building - Vacuum insulating glass - Part 1: Basic specification of products and evaluation methods for thermal and sound insulating performance

DIN EN 1279-6:2018 建筑玻璃 中空玻璃 第6部分：工厂生产控制和定期测试；德文版 EN 1279-6:2018

This document describes the routine factory production control, the recurring tests and the monitoring and test procedures to verify that a multi-pane insulating glass unit (IGU) conforms to the system description.

Glass in building - Insulating glass units - Part 6: Factory production control and periodic tests; German version EN 1279-6:2018

ISO/TS 18178:2018 建筑玻璃.建筑用层压太阳能光伏玻璃

Glass in building - Laminated solar photovoltaic glass for use in buildings

T/LJH 007-2018 既有建筑节能改造及新建被动式低能耗建筑用门窗幕墙玻璃应用技术规程

1.总则；2.术语；3.材料；4.设计；5.施工；6.验收。

Technical regulations for the application of doors, windows and curtain walls for energy-saving renovation of existing buildings and new passive low-energy buildings

BS EN 1096-4:2018 建筑中的玻璃 镀膜玻璃 产品标准

Glass in building. Coated glass. Product standard

BS EN 1279-6:2018 建筑中的玻璃 中空玻璃单元 工厂生产控制和定期测试

Glass in building. Insulating glass units. Factory production control and periodic tests

BS EN 1279-1:2018 建筑中的玻璃 中空玻璃单元 一般性、系统描述、替代规则、公差和视觉质量

Glass in building. Insulating glass units. Generalities, system description, rules for substitution, tolerances and visual quality

BS EN 1279-4:2018 建筑中的玻璃 中空玻璃单元 边缘密封组件和插入件物理属性的测试方法

Glass in Building. Insulating Glass Units. Methods of test for the physical attributes of edge seal components and inserts

BS EN 1279-3:2018 建筑中的玻璃 中空玻璃单元 气体泄漏率和气体浓度容差的长期测试方法和要求

Glass in building. Insulating glass units. Long term test method and requirements for gas leakage rate and for gas concentration tolerances

EN 1096-4:2018 建筑玻璃.镀膜玻璃.第4部分:一致性评估.产品标准

Glass in building - Coated glass - Part 4: Product standard