83.040.01 橡胶和塑料用原料综合 标准查询与下载

ASTM D5948-05(2020) 热固性模塑化合物的标准规范

1.1 This specification covers the basic properties of thermoset molding compounds and the test methods used to establish the properties. 1.2 Classification—Molding thermosetting plastic compounds shall be of the following resins and are covered by the individual specification sheets (see 5.1 and Annex A1 – Annex A8). Resin Phenolic, cellulose filled Phenolic, mineral/glass filled Melamine Polyester Diallyl iso-phthalate Diallyl ortho-phthalate Silicone Epoxy NOTE 1—There is no known ISO equivalent to this standard. 1.3 Order of Precedence—In the event of a conflict between the text of this specification and the references cited in Section 2 (except for related specification sheets), the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1.4 The values stated in SI units are to be considered standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Molding Compounds, Thermosetting

T/CPUIA 0001-2020 休闲鞋大底用聚氨酯原液

本文件规定了休闲鞋大底用聚氨酯原液的要求、试验方法、检验规则及标志、包装、运输和贮存。

Polyurethane System for Casual Outsoles

T/CSTM 00130-2020 碳五石油树脂

本文件规定了碳五石油树脂的技术要求、试验方法、检验规则、标志、质量证明书、包装、贮存和运输要求。 本文件适用于以混合碳五或间戊二烯为主要原料，在催化剂的作用下，经过前处理、聚合、水洗、蒸馏和造粒而制得的碳五石油树脂产品。本文件未给出的其他用途碳五石油树脂以及改性碳五石油树脂可参照本文件执行。

C5 hydrocarbon resin

T/FSI 050-2020 甲基氯硅烷高沸点混合物

本标准规定了甲基氯硅烷高沸点混合物(以下简称高沸物)的技术要求、试验方法、检验规则及标 志、包装、运输、贮存及安全。 本标准适用于用硅粉和氯甲烷直接合成法生产的混合甲基氯硅烷经闪蒸或精馏处理得到的沸点高 于二甲基二氯硅烷的有机硅硅烷混合物

Methylchlorosilane high boiling point mixture

KS M ISO 6225-1-2019 天然生橡胶 蓖麻油含量的测定 第1部分：薄层色谱法测定蓖麻油甘油酯含量

Rubber, raw, natural－Determination of castor oil content－Part 1：Determination of castor oil glyceride content by thin-layer chromatography

DB61/T 1285-2019 沥青路面超薄磨耗层施工技术规范

Technical specification for construction of ultra-thin wearing layer of asphalt pavement

T/FSI 045-2019 甲基氟硅油

本标准规定了甲基氟硅油的产品结构式和型号、技术要求、试验方法、检验规则、标志、包装、运 输和贮存。 本标准适用于以三氟丙基甲基环三硅氧烷（D 3 F）、八甲基环四硅氧烷或六甲基环三硅氧烷或二甲 基硅氧烷混合环体原料，与甲基封端剂在催化剂作用下制备得到的甲基氟硅油。

Methyl Fluorosilicone

T/FSI 044-2019 端乙烯基氟硅油

本标准规定了端乙烯基氟硅油的产品结构式和型号、技术要求、试验方法、检验规则、标志、包装、 运输和贮存。 本标准适用于以三氟丙基甲基环三硅氧烷（D3F）、八甲基环四硅氧烷或六甲基环三硅氧烷或二甲 基硅氧烷混合环体原料，与乙烯基封端剂在催化剂作用下制备得到的端乙烯基氟硅油。

Vinyl-terminated fluorosilicone oil

T/FSI 046-2019 电力行业用有机硅产品分类与命名

本标准规定了电力行业用有机硅产品的分类与命名。 本标准适用于电力行业用有机硅产品的分类与标记，在电力行业中使用有机硅产品时，这些命名符 号应置于商品名称之前

Classification and naming of silicone products used in electric power industry

T/FSI 041-2019 端环氧基甲基硅油

本标准规定了端环氧基甲基硅油的技术要求、试验方法、检验规则、标志、包装、运输和贮存。本 标准适用于端含氢二甲基硅油与烯丙基缩水甘油醚合成的端环氧基甲基硅油。

Epoxy terminated methyl silicone oil

T/ZZB 1141-2019 间接法氧化锌-80母胶粒

本标准规定了间接法氧化锌-80母胶粒的范围、规范性引用文件、术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本标准适用于以间接法氧化锌为主要原料，经混炼制得的氧化锌-80母胶粒。

Indirect method Zinc oxide-80 Colloidal particles

ASTM D5603-19a 橡胶复合材料的标准分类&x2014；再生硫化橡胶

1.1 This classification covers the compounding material commercially known as recycled vulcanizate particulate rubber. Recycled vulcanizate particulate rubber is the product that results when vulcanizate rubber has been processed by some means to obtain a desired particle size distribution. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Rubber Compounding Materials—Recycled Vulcanizate Rubber

ASTM D8268-19 橡胶复合材料的标准实施规程&x2014；再生硫化橡胶颗粒的评价

1.1 This practice covers the evaluation methods for the compounding material commercially known as recycled vulcanizate particulate rubber. The methods are of general usage in quality control or are needed for the classification of the recycled vulcanizate particulate rubber according to Classification D5603. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Rubber Compounding Materials—Evaluation of Recycled Vulcanizate Particulate Rubber

ASTM D5603-19 橡胶复合材料的标准分类&x2014；再生硫化颗粒橡胶

Standard Classification for Rubber Compounding Materials—Recycled Vulcanizate Particulate Rubber

T/FSI 016-2019 甲基低含氢硅油

本标准规定了甲基低含氢硅油产品的结构式、型号、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于以聚二甲基硅氧烷环体、甲基高含氢硅油和六甲基二硅氧烷为原料，采用酸性催化剂制备的侧链含氢硅油。

Methyl low hydrogen silicone oil

T/FSI 018-2019 乙烯基封端的二甲基硅油

本标准规定了乙烯基封端的二甲基硅油的结构式、型号、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于以二甲基硅氧烷环体和四甲基二乙烯基二硅氧烷为原料，在碱性或者酸性催化条件下制备的乙烯基封端的二甲基硅油。

Vinyl terminated simethicone

T/FSI 021-2019 甲基二氯硅烷

本标准规定了甲基二氯硅烷的技术要求、试验方法、检验规则、标志、包装、运输和贮存、安全。 本标准适用于由直接合成法生产的混合甲基氯硅烷经分馏提纯的甲基二氯硅烷。 分子式：(CH3)H SiCl2 结构式：                       H                               |                          CH3- Si -Cl                               |                              Cl 相对分子量：115.02（按2016年国际相对原子质量）

Methyldichlorosilane

T/FSI 017-2019 端含氢二甲基硅油

本标准规定了端含氢二甲基硅油的产品结构式、型号、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于以聚二甲基硅氧烷环体和四甲基二硅氧烷为原料，采用酸性催化剂制备的端含氢二甲基硅油。

Hydrogen-terminated simethicone

T/FSI 020-2019 甲基氯硅烷共沸物

本标准规定了甲基氯硅烷共沸物的要求、检验规则、试验方法及标志、包装、运输、贮存和安全。 本标准适用于以甲基氯硅烷混合物为原料通过精馏共沸馏塔分离出的甲基氯硅烷共沸物。甲基氯硅烷共沸物主要由三甲基氯硅烷、甲基氢二氯硅烷、四氯化硅等组分构成

Methylchlorosilane azeotrope

ASTM D6339-11(2019) 间规聚苯乙烯模塑和挤压（SPS）规范的标准分类系统和基础

1.1 This classification system covers syndiotactic polystyrene materials including homopolymer, copolymers, blends, and impact modified, suitable for molding and extrusion. Recycled product will be addressed in a separate standard. 1.2 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in fabrication of end use items or parts. It is not intended for the selection of matierials. Material selection can be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification system, and the economics. 1.3 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be called out using the suffixes given in Section 5. NOTE 1—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)