83.040.01 橡胶和塑料用原料综合 标准查询与下载

ASTM D8238-18 定量可提取天然橡胶（GNR）蛋白质的免疫学试验方法

1.1 This test method covers an immunological method to determine the amount of protein in Guayule Natural Rubber (GNR) and its products using rabbit antisera specific for Guayule Natural Rubber latex proteins. This immunoassay procedure quantitatively measures the level of GNR proteins in solution using an inhibition format. The samples may include but are not restricted to, gloves or other GNR product extracts, and liquid GNR samples which have been collected in order to measure the protein levels. 1.2 For the purpose of this test method, the range of protein will be measured in terms of microgram to milligram quantities. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Immunological Assay to Quantify Extractable Guayule Natural Rubber (GNR) Proteins

T/QYBX 001-2018 电子线路板再生树脂玻纤粉

项目　40目以下　40～60目　60～100目　100～200目　200目以上 含水率/%                        　≤5　≤5　≤3　≤2　≤1.5 pH值                　7.4～8.8　7.4～8.8　7.4～8.8　7.4～8.8　7.4～8.8 堆积密度/（g/cm3  ）　＜1.45　＜1.45　＜1.6　＜1.7　＜1.7 吸油值/（g/100g）  　≤40　≤40　≤70　≤80　≤80 粒径/μ m　≥380　380～250　250～150　150～75　≤75 铜含量/%　≤0.3　≤0.3　≤0.3　≤0.3　≤0.3

Electronic circuit board recycled resin glass fiber powder

ASTM D6068-10(2018) 测定塑料材料的J-R曲线的标准试验方法

1.1 This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials. 1.2 This test method is intended to characterize the slow, stable crack growth resistance of bend-type specimens in such a manner that it is geometry insensitive within limits set forth in this test method. 1.3 The recommended specimens are the three-point bend (SE(B)) and pin-loaded compact tension (C(T)) specimens. Both specimens have in-plane dimensions of constant proportionality for all sizes. Specimen configurations other than those recommended in this test method may require different procedures and validity requirements. 1.4 This test method describes a multiple specimen method that requires optical measurement of crack extension from fracture surfaces. It is not recommended for use with materials in which the crack front cannot be distinguished from additional deformation processes in advance of the crack tip. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining J-R Curves of Plastic Materials

ASTM D6099-18 聚氨酯原材料的标准试验方法:中高酸度芳香异氰酸酯中酸度的测定

1.1 This test method determines the acidity, expressed as parts per million (ppm) of HCl, in aromatic isocyanate samples of greater than 100–ppm acidity. The test method is applicable to products derived from toluene diisocyanate and methylenebis-(4–phenylisocyanate) (see Note 1). NOTE 1—This test method is equivalent to ISO 14898, Test Method A. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates

T/FSI 013-2017 七甲基二硅氮烷

本标准规定了七甲基二硅氮烷的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以三甲基一氯硅烷和一甲氨为主要原料，经合成精制而制成的七甲基二硅氮烷。

Heptamethyldisilazane

T/FSI 009-2017 六甲基环三硅氧烷

本标准规定了六甲基环三硅氧烷的要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于以二甲基二氯硅烷为原料经盐酸水解、裂解所制得的二甲基硅氧烷混合环体,再经精馏提纯而得的六甲基环三硅氧烷。

Hexamethylcyclotrisiloxane

T/FSI 010-2017 十甲基环五硅氧烷

本标准规定了十甲基环五硅氧烷的要求、试验方法、检验规则以及标志、包装、运输及贮存。    本标准适用于以二甲基二氯硅烷为原料经盐酸水解、裂解所制得的二甲基硅氧烷混合环体, 二甲基硅氧烷混合环体精馏得到十甲基环五硅氧烷。

Decamethylcyclopentasiloxane

T/FSI 007-2017 高沸硅油

本标准规定了高沸硅油的技术要求、试验方法、检验规则以及标志、包装、运输和贮存要求。 本标准适用于以甲基氯硅烷混合单体经过精馏制得的高沸物为主要原料，再经醇解或水解工艺制得的高沸硅油。高沸硅油主要成分为聚甲基硅氧烷混合物,其结构以硅氧键、硅碳键、硅硅键为主，并带有部分支链。高沸硅油适用于消泡剂、防水剂、隔离剂等行业，食品、医疗等行业需另行检测。

Silicon oil synthesized from organosilicon high-boiling components

T/FSI 012-2017 四甲基二乙烯基二硅氮烷

本标准规定了四甲基二乙烯基二硅氮烷的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以二甲基乙烯基氯硅烷和液氨为主要原料，经合成精制而制成的四甲基二乙烯基二硅氮烷。

Tetramethyl divinyl disilazane

KS M ISO 20299-2-2017(2022) 橡胶包包装膜第2部分:天然橡胶

Film for wrapping rubber bales－Part 2：Natural rubber

KS M ISO 20299-2-2017 橡胶包包装膜第2部分:天然橡胶

Film for wrapping rubber bales－Part 2：Natural rubber

KS M ISO 20299-2:2017 橡胶面纱包装用胶片 第2部分：天然橡胶

Film for wrapping rubber bales－Part 2：Natural rubber

BS ISO 20299-2:2017 用于包裹橡胶包的薄膜 天然橡胶

Film for wrapping rubber bales. Natural rubber

ISO 20299-2:2017 橡胶包包装用薄膜.第2部分:天然橡胶

This document specifies the material and physical property requirements for non-strippable low density polyethylene film for wrapping natural rubber bales comprising of block natural rubber of 33,33 kg or 35 kg and natural rubber ribbed smoked sheets including bales of 33,33 kg, 35 kg, 50 kg and 111,11 kg, or any other bale weights as mutually agreed between the parties, and intended to keep the bales separate during transportation and storage.

Film for wrapping rubber bales - Part 2: Natural rubber

GOST R 52367-2017 顺式异戊二烯合成橡胶. 通用规格

Synthetic cis-isoprene rubber. General specifications

QB/T 4908-2016 人造革用水性聚氨酯粘接浆料

本标准规定了人造革用水性聚氨酯粘接浆料的分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于以多异氰酸酯、多元醇和水为主要材料，经化学反应、物理混合形成的人造革用水性聚氨酯或改性水性聚氨酯粘接浆料。

Waterborne polyurethane adhesive slurry for artificial leather

BS ISO 20299-1:2015 橡胶包包装用薄膜.丁二烯橡胶(BR)和丁苯橡胶(SBR)

Film for wrapping rubber bales. Butadiene rubber (BR) and styrene-butadiene rubber (SBR)

GSO ISO 20299-2:2014 包装用橡胶箔包装 第2部分：天然橡胶

This part of ISO 20299 specifies the material and physical property requirements for non-strippable high melting point film for wrapping natural-rubber bales, intended to keep the bales separate during storage.

Film for wrapping rubber bales - Part 2: Natural rubber

GSO ISO 20299-1:2014 包装用橡胶箔包装 第1部分：顺丁橡胶和丁苯橡胶

This part of ISO 20299 specifies the material and physical property requirements for non-strippable film for wrapping general-purpose synthetic rubber bales, intended to keep the bales separate during storage, for example for wrapping — styrene-butadiene rubber (SBR); — butadiene rubber (BR). Certain applications or processing methods require the removal of the film. This part of ISO 20299 does not deal with strippable films.

Film for wrapping rubber bales - Part 1: Butadiene rubber (BR) and styrene-butadiene rubber (SBR)

HG/T 4611-2014 载重轮胎胎面精细再生橡胶

本标准规定了载重轮胎胎面精细再生橡胶(以下简称再生橡胶)的要求、试验方法、检验规则、包装、标志、运输与贮存。本标准适用于用废载重轮胎胎面胶胶粉制造的载重轮胎胎面精细再生橡胶。

Refined reclaimed rubber from truck tire treads