83.140.50 密封件 标准查询与下载

ASTM C1815-17 在压缩或张力期间定期测量和监测密封剂尺寸对稳定性的标准实施规程

5.1 Many sealants have been observed to dimensionally change following a period of compression or tension, such as occurs during exposure in accordance with Practice C1589. It has been shown that for some sealants, increasing exposure to weathering increases the time required for dimensional stability and decreases the magnitude of dimensional change. Dimensional stability and knowledge of the stable sealant dimensions are critical to the accurate measurement of the sealant’s modulus by a test such as Test Method C1735. 5.2 This practice will find application in improving the accuracy of the modulus determined by a standard such as Test Method C1735 by using the accurate dimensions determined by this practice after stability is attained. 1.1 This practice covers a procedure for measuring and monitoring the physical dimensions of an elastomeric joint sealant in a test specimen configuration described in Test Method C719 following a period of compression or tension. These sealant materials are typically highly filled elastic materials. The dimensional change of these sealant materials is determined by measuring the dimensions at specific intervals over a period of time. 1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Periodically Measuring and Monitoring Sealant Dimensions to Stability Following a Period of Compression or Tension

ASTM C1115-17 密实弹性体硅橡胶衬垫和附件的标准规格

8.1 This specification describes types (based on resistance to tearing and compression set), grades (based on durometer hardness), class (based on flame propagation requirements), and surfaces (based on surface characteristics) of products as listed in Section 4 for various applications. It is essential, therefore, that the applicable type, grade, class, and surface be specified, as well as other options stated, so that the proper product is provided for the intended use. 1.1 This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building construction and also as components in structural silicone sealant glazing systems. 1.2 The following precautionary statement pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.4 The values stated in metric (SI) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information purposes only. 1.5 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories

GOST R 57399-2017 硅基橡胶垫圈和附件. 技术要求

Silicone based rubber gaskets and accessories. Technical requirements

T/TLRIA 0001-2016 家用燃气表橡胶膜片

橡胶材料的物理性能、膜片的物理性能、　膜片的外观质量、膜片尺寸按图纸规定、其厚度尺寸及公差为0.2±0.02mm。

Household gas meter rubber diaphragm

HG/T 2292-2016 环形防喷器胶芯

本标准规定了环形防喷器胶芯的术语和定义，分类、规格和参数，要求和试验方法，检验规则以及标志、包装、运输和贮存。 本标准适用于石油天然气勘探、钻井、试油、修井井控用环形防喷器胶芯(以下简称胶芯)。

Rubber core of the annular blowout preventer

HG/T 5094-2016 遇油、遇水自膨胀橡胶封隔器

本标准规定了遇油、遇水自膨胀橡胶封隔器的术语和定义，结构、代号，要求，检验规则以及标志、包装、运输和贮存。 本标准适用于油、气、水井完井、堵漏作业用遇油、遇水自膨胀封隔器(简称自膨胀封隔器)。

Oil and water swellable packer

HG/T 2702-2016 扩张式封隔器胶筒

Expansion packer rubber barrel

HG/T 2701-2016 压缩式封隔器胶筒

Compression packer rubber barrel

GSO ISO 9631:2015 橡胶密封件 110℃以下热水供应管道用连接环 材料技术规范

This International Standard specifies requirements for materials used in vulcanized-rubber seals for hot potable and non-potable water supply (up to 110 °C). The different seal designations specified are defined according to seal type, seal application and the requirements for a particular seal (see Table 3). General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard is intended to be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for use with all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. It is applicable to elastomeric components of composite and non-composite seals. In the case of composite seals made from materials with hardnesses ranging from 76 IRHD to 95 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material participates in the sealing function or contributes to the long-term stability of the seal. Joint rings made from cellular rubber materials or with enclosed voids as part of their design are not covered by this International Standard.

Rubber seals -- Joint rings for pipelines for hot-water supply up to 110 degrees C -- Specification for the material

GSO ISO 16010:2015 柔性密封件 输送气体燃料和碳氢化合物的管道和配件中使用的密封件的材料要求

This International Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from –5 °C up to 50 °C and in special cases from –15 °C up to 50 °C, for the following: a) general applications (see Table 4, type G series): — gaseous fuel [manufactured, natural and liquefied petroleum gas (LPG) in the gaseous phase], — hydrocarbon fluids with an aromatic content up to 30 % (by volume), including LPG in the liquid phase; b) special applications (see Table 4, type H): — materials suitable for carrying gaseous fuels containing gas condensates and hydrocarbon fluids of unrestricted aromatic content. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard should be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for all pipeline materials, including iron, steel, copper and plastics. In the case of composite sealing rings, the requirements in 4.2.8 and 4.2.9 apply only when the materials used for any elastomeric parts come into contact with gaseous fuel or hydrocarbon fluid. Elongation at break, tensile strength, compression set and stress relaxation requirements for materials of hardness classes 80 and 90 apply only when they constitute that part of the seal which participates directly in the sealing function or contributes directly to long-term stability. This International Standard is not applicable to the following: — seals made from cellular materials; — seals with enclosed voids as part of their design; — seals required to be resistant to flame or to thermal stress; — seals which contain splices joining pre-vulcanized profile ends.

Elastomeric seals -- Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

HG/T 4785-2014 车用空气滤清器橡胶密封件

本标准规定了车用空气滤清器橡胶密封件的分类、符号、结构及标识，要求，检验规则，标志、包装、运输和贮存。 本标准适用于汽车空气滤清器橡胶密封件(以下简称密封件)。

Rubber seals for air cleaner of automobile

HG/T 2021-2014 耐高温润滑油O形橡胶密封圈

本标准规定了耐高温润滑油O形橡胶密封圈的要求，试样，检验规则，标志、包装、运输和贮存。 本标准适用于耐高温润滑油用O形橡胶密封圈。

O-rings resistant to high temperature and oil

GSO ISO 4633:2014 橡胶密封材料技术条件 给排水管连接接头用橡胶圈

This International Standard specifies requirements for materials used in vulcanized rubber seals for cold drinking-water supplies (up to 50 °C); drainage, sewerage and rainwater systems (continuous flow up to 45 °C and intermittent flow up to 95 °C). The different designations of seals specified are defined according to their type, application and requirements. General requirements for finished joint seals are also given: any additional requirements called for by the particular application are specified in the relevant product standards, taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This International Standard is intended to be used where appropriate with product standards which specify performance requirements for joints. This International Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. It is applicable to elastomeric components of composite or non-composite seals. In the case of composite seals for materials of hardness ranges from 76 IRHD to 95 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function or in the long-term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this International Standard.

Rubber seals- Joint rings for water supply, drainage and sewerage pipelines- Specification for materials

HG/T 4624-2014 汽车滑销防尘密封保护套

本标准规定了汽车滑销防尘密封保护套(以下简称保护套)的要求、检验规则及标志、包装、运输和贮存。本标准适用于载重汽车的制动盘之间的滑销防尘密封保护套。

Anti-dust sealing protective sleeve of vehicle sliding pin

HG/T 4622-2014 耐二甲醚橡胶密封材料

本标准规定了耐二甲醚橡胶密封材料的要求、检验规则、标志、包装、运输、贮存等。本标准适用于耐二甲醚的橡胶密封材料,也适用于耐液化石油气二甲醚混合液的橡胶密封材料。

Rubber compounds for seals used for dimethyl ether

HG/T 4623-2014 船用货舱盖橡胶密封带

本标准规定了船舶货舱盖橡胶密封带(以下简称密封带)的要求、密封带试验方法、检验规则、标志、包装、贮存。本标准适用于货船大舱口盖用密封带。

Sealing rubber for hatch covers of cargo ship

GOST ISO 16010-2013 弹性密封件. 输送气体燃料和烃类液体的管和配件用密封件的材料要求

Elastomeric seals. Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

GOST 32600-2013 泵. 离心和旋转式泵用轴封系统. 通用技术要求和控制方法

Pumps. Shaft sealing systems for centrifugal and rotary pumps. General technical requirements and control methods

GOST 32586-2013 汽车技术用振动绝缘橡胶和增强型橡胶. 规格

Vibroinsulators rubber and rubber-reinforced for automotive technic. Specifications

HG/T 4392-2012 汽车滤清器橡胶密封件

本标准规定了汽车滤清器橡胶密封件的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于汽车机油滤清器、燃油滤清器用橡胶密封件。本标准不适用于汽车空气滤清器密封件。

Rubber seals for automobile filter