83.140.50 密封件 标准查询与下载

ISO/DIS 5892 橡胶建筑垫片《预成型固体硫化结构垫片用材料》规范

Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification

HG/T 3096-2011 水闸橡胶密封件

本标准规定了水闸橡胶密封件和橡塑复合密封件的要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于水利、水电工程闸门用橡胶密封件和橡塑复合密封件（以下简称密封件）。

Rubber seals of water gate

GSO EN 682:2011 柔性密封件 输送气体和碳氢化合物流体的管道和配件密封件的材料要求

This European Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from - 5 °C up to 50 °C and in special cases from - 15 °C up to 50 °C, for the following: General applications (see Table 4, type G) a) gaseous fuel (manufactured, natural and liquefied petroleum gas [LPG] in gaseous phase); b) hydrocarbon fluids with aromatic content up to 30 % (V/V), including LPG in liquid phase. Special applications (see Table 4, type H) Materials suitable for carrying gaseous fuels containing gas condensates and hydrocarbon fluids of unrestricted aromatic content. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This European Standard should be used where appropriate with product standards which specify performance requirements for joints. This European Standard is applicable to joint seals for all pipeline materials including iron, steel, copper and plastics. In the case of composite seals requirements in 4.2.8 and 4.2.9 apply only when the materials used for any elastomeric parts come into contact with gaseous fuel or hydrocarbon fluid. Elongation at break, tensile strength, compression set and stress relaxation requirements for materials of hardness categories 80 and 90 apply only when they constitute that part of the seal which participates directly in the sealing function or in long term stability. This standard is not applicable to the following: a) seals made from cellular materials; b) seals with enclosed voids as part of their design; c) seals with requirements of resistance to flame or to thermal stress; d) seals which contain splices joining pre-vulcanised profile ends.

Elastomeric Seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

ASTM D6515-00(2010) 橡胶轴封的标准试验方法弯曲恢复率的测定

Standard Test Method for Rubber Shaft Seals Determination of Recovery From Bending

SNI 7655-2010 LPG阀门上的橡胶密封圈（rubber seal）

Rubber seal (rubber seal) on LPG valve

HG/T 4116-2009 滚筒洗衣机橡胶门封

本标准规定了滚筒洗衣机橡胶门封的分类、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于烘干型和非烘干型滚筒洗衣机橡胶门封。

Rubber seals for washing machine window

HG/T 4117-2009 洗衣机橡胶水封

本标准规定了洗衣机橡胶水封的基本结构、尺寸代号及尺寸标志、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于轴径为10mm-100mm、工作压力不大于0.05MPa的全自动波轮洗衣机和全自动滚筒洗衣机橡胶水封。

Rubber seals used in shaft of washing machine

HG/T 2181-2009 耐酸碱橡胶密封件材料

本标准规定了耐酸碱橡胶密封件材料的分类和标记、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于一般耐硫酸、盐酸、硝酸、氢氧化钠、氢氧化钾的橡胶密封件材料。

Acid and alkali resistant rubber compounds for seals

KS M ISO 6448-2009(2014) 石油产品供应管和配件用橡胶密封圈材料规范

Rubber seals－Joint rings used for petroleum product supply pipes and fittings－Specification for material

KS M ISO 6447:2009 橡胶密封.供气管和配件用密封环.材料规范

이 표준은 50 ℃ 이하의 사용 온도에서 가스 연료(제조된 것이나 또는 천연 가스) 공급

Rubber seals－Joint rings used for gas supply pipes and fittings－Specification for material

KS M ISO 6448:2009 橡胶密封.提供石油产品管道和配件用密封圈.材料规范

이 표준은 석유 공급 파이프와 피팅을 위해 가황된 고체 고무 씰(seal)용 링으로 쓰이는

Rubber seals－Joint rings used for petroleum product supply pipes and fittings－Specification for material

KS M ISO 6447-2009(2014) 橡胶密封供气管和配件用连接环材料规范

Rubber seals－Joint rings used for gas supply pipes and fittings－Specification for material

GSO ISO 23711:2009 柔性密封件 排水和水应用中使用的管道接头密封件的材料要求 热塑性密封件

This International Standard specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in: a) thermoplastic piping systems for non-pressure waste water discharge (intermittent flow at up to 95 °C) inside buildings; b) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow at up to 45 °C and intermittent flow at up to 95 °C); c) thermoplastic rainwater piping systems. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications – Thermoplastic elastomers

KS M ISO 9631:2008 橡胶密封件.最高温度为110℃的热水供给管道的密封环.材料规范

이 표준은 마실 수 있거나 또는 없는 온수(110 ℃ 이하) 공급기용 가황 고무 씰(sea

Rubber seals－Joint rings for pipelines for hot-water supply up to 110 ℃－Specification for the material

HG/T 2810-2008 往复运动橡胶密封圈材料

本标准规定了普通液压系统耐石油基液压油和润滑油的往复运动橡胶密封圈材料的分类、要求、试验方法及标志、标签、包装、贮存。 本标准适用于在普通液压系统耐石油基液压油和润滑油中使用的往复运动橡胶密封圈材料。

Compounds of reciprocating rubber seals

HG/T 2579-2008 普通液压系统用O形橡胶密封圈材料

本标准规定了普通液压系统耐石油基液压油和润滑油（脂）用O形橡胶密封圈材料的分类、要求、试验方法、检验规则及标识、包装、贮存。 本标准适用于普通液压系统耐石油基液压油和润滑油（脂）、工作温度范围分别为-40℃～+100℃和-25℃～+125℃的O形橡胶密封圈材料。

Rubber Compounds of O-Rings used for Hydraulic fluid power System

HG/T 4074-2008 贮气柜用橡胶密封膜

本标准规定了贮气柜用橡胶密封膜（以下简称密封膜）的要求、检验规则、试验方法、标志、包装、运输和贮存。 本标准适用于设计压力在6kPa以下，用于冶金、石油化工、城市煤气工程、煤炭污水处理等行业贮存转炉煤气、高炉煤气、炼油厂尾气、石油拌生气、矿井气、沼气和天然气等气体的贮气柜用橡胶密封膜。 本标准不适用于由经纬交织结构为基材的贮气柜用橡胶密封膜。

Rubber Sealing Membrane for Gas Holder

KS M ISO 16010:2007 弹性密封件.传送气体燃料和烃类液体的管和配件用密封件的材料要求

이 규격은 -5∼50 ℃, 그리고 특별한 경우 -15∼50 ℃에서 작동하는 공급용 파이프,

Elastomeric seals-Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

KS M ISO 16010-2007(2017) 弹性密封－用于输送气体燃料和碳氢化合物流体的管道和配件的密封材料要求

Elastomeric seals－Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

HG/T 3326-2007 采煤综合机械化设备橡胶密封件用胶料

本标准规定了采煤综合机械化设备用橡胶密封件胶料的要求、试验方法、检验规则及标志、标签、包装、贮存。 本标准规定的材料适用于制造采煤综合机械化设备中液压支架及单体支柱液压系统用橡胶密封件。

Rubber compound for coal-digger parts of comprehensive mechanization equipment