83.140.50 密封件 标准查询与下载

HG 2950-1999 汽车制动气室橡胶隔膜

本标准规定了汽车制动气室橡胶隔膜的要求、抽样、试验方法及标志、包装、运输和贮存。 本标准适用于汽车制动气室用橡胶隔膜。

Rubber diaphragms for brake chamber in automobiles

HG/T 3088-1999 车辆门窗橡胶密封条

本标准规定了车辆门窗橡胶密封条的要求、抽样、试验方法及标志、包装、运输和贮存。 本标准适用于车辆门窗用橡胶、海绵橡胶及复合型橡胶密封条。

Rubber sealing stips of doors and windows for vehicles

HG/T 3612-1999 汽车液压盘式制动缸用橡胶密封圈

本标准规定了使用非石油基制动液的汽车盘式制动缸用橡胶密封圈的分类、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于非石油基制动液的汽车盘式制动缸用橡胶密封圈。

Rubber seals used for automobile hydraulic disc brake cylinders

SR 7278-1999 橡胶密封垫．一般质量技术要求

Prezentul standard se refer? la garniturile de cauciuc sintetic, vulcanizate, rezistente la produse petroliere. Standardul nu face referire la garniturile de uz special ale c?ror condi?ii de calitate sunt reglementate prin standarde ?i specifica?ii tehnic

Petroleum rezistant rubber gasket - General technical requirements for quality

HG 2865-1997 汽车液压制动橡胶皮碗

本标准规定了汽车液压制动橡胶皮碗的分类、要求、抽样、试验方法及标志、包装、运输和贮存。 本标准适用于汽车液压制动缸(包括主缸和轮缸)用的橡胶皮碗。

Hydraulic brake rubber cups for automobiles

ASTM D5973-97(2007) 用于膨胀节密封的带钢封闭边缘围栏的弹性带密封件的标准规范

1.1 This specification covers the material requirements for preformed elastomeric strip seals and the corresponding steel locking edge rail used in expansion joint sealing. The scope of this specification is limited to preformed non-reinforced strip seals that mechanically lock into structural steel locking lugs. The sealing element can consist of a single layer strip or have multiple webs depending on individual project requirements. The structural steel locking edge rail shall be anchored into the structure in accordance with the purchaser's specific details. While the scope of this specification is limited to the materials used in fabrication of strip sealing systems, it is recommended that a practical means of testing the watertightness aspects of the individual systems either in the field or at a testing laboratory be developed. When used on highway bridges, limits on maximum joint opening and minimum steel thicknesses need to be addressed. 1.2 The values stated in the inch-pound system shall be considered as standard.

Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing

HG/T 2811-1996 旋转轴唇形密封圈橡胶材料

本标准规定了旋转轴唇形密封圈用橡胶材料的分类、要求、抽样、试验方法及标志、标签、包装、贮存。 本标准适用于旋转轴唇形密封圈橡胶材料。

Rotary shaft lip seal rubber material

HG/T 2809-1996 浮顶油罐软密封装置橡胶密封带

本标准规定了浮顶油罐软密封装置橡胶密封带的结构、尺寸及公差、要求、试验方法、检验规则和标志、包装、运输、贮存等。 本标准适用于织物两面涂覆耐原油及轻质油品(苯及芳香烃除外)的橡胶而制成的浮顶油罐软密封装置橡胶密封带。

Rubber sealing tape for soft sealing device of floating roof oil tank

BS EN 549:1995 燃气器具和设备密封件和隔膜用橡胶材料规范

This standard specifies requirements and associated test methods for vulcanized rubber materials used in gas appliances and equipment in contact with 1st, 2nd and 3rd family combustible gases. It also establishes a classification based on temperature range and hardness. This standard is applicable to materials from which are manufactured homogeneous seals and homogeneous or reinforced diaphragms. The normal range of operating temperatures covered by this standard is 0 ℃ to +60 ℃. Tests are also included for applications using diaphragms within the range - 20 ℃ to +80 ℃ and seals within the range -20 ℃ to +150 ℃. For temperatures outside these ranges the user should contact the manufacturer regarding the suitability of the rubber material. This standard includes two normative annexes for the verification that a component (finished product) was produced from a previously type tested material complying with requirements of this standard as declared by the appliance or equipment manufacturer or supplier of the component. This standard is not applicable to silicone rubber used either above 200 mbar nominal pressure or at temperatures below 0 ℃ with 3rd family gases as there is possibility of condensation. This standard is also not applicable to seals and diaphragms for devices in gas transmission systems nor in such equipment used in 1st and 2nd family gas distribution systems.

Specification for rubber materials for seals and diaphragms for gas appliances and gas equipment

HG/T 2701-1995 油气田用压缩（YS）式封隔器胶筒

本标准规定了油气田用压缩(YS)式封隔器胶筒的技术要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于油气田分层开采、测试、注水、酸化和压裂用压缩(YS)式封隔器胶简。

Compression (YS) packer rubber cartridge for oil and gas fields

HG/T 2702-1995 油气田用扩张（KZ）式封隔器胶筒

 本标准规定了油气田用扩张(KZ)式封隔器胶简的技术要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于油气田分层测试、注水、酸化和压裂用扩张(KZ)式封隔器胶简。

Expansion (KZ) packer rubber cartridge for oil and gas fields

HG/T 2700-1995 橡胶垫片密封性的试验方法

Test method for tightness of rubber gaskets

DIN EN 549:1995 燃气灶具和燃气器具用密封件和膜片的橡胶材料; 德文版本 EN 549:1994

This document specifies and classifies requirements for vulcanized rubber materials, which may be homogenous or reinforced, used in gas burning applicances and associated control devices in contact with 1st, 2nd or 3rd family combustible gases. This document does not cover control and safety devices in gas transmission systems, or such equipment used in 1st and 2nd family gas distribution systems.

Rubber materials for seals and diaphragms for gas appliances and gas equipmemt; German version EN 549:1994

NF D36-205:1995 燃气器具和设备的密封件和膜片用橡胶材料

Rubber materials for seals and diaphragms for gas appliances and gas equipment.

JIS B 2403:1995 V型密封件

この規格は，石油系作動油を使用する一般油圧機器用Vパツキン(以下，Vパツキンという。）について規定する。

V packings

SNI 09-3766-1995 机车油箱盖用橡胶圈

Rubber packing for motor vehicles gasoline tank cover

SNI 09-3767-1995 摩托车连轴器外壳用橡胶板

Absorber rubber for motor cycles coupling house

JIS K 6380:1994 工业用橡胶填料

Industrial rubber packing materials -- Classification system

HG/T 2293-1992 离合器用橡胶气胎

Rubber pneumatic tire for clutch

HG/T 2330-1992 旋转轴唇形密封圈贮存、维护和安装

Rotary shaft lip seal storage, maintenance and installation