91.100.50 粘合料、密封材料 标准查询与下载

ASTM D3617/D3617M-17(2022) 应用过程中组合屋顶系统的取样和分析

1.1 This practice is a guide for removing specimens for built-up bituminous roof systems during application, but before the application of flood coating and top surfacing, for determining the approximate quantities of the components and the possible presence of moisture, or dry spots between plies, in the field. Components may consist of: 1.1.1 Insulation, when part of the roof membrane system, 1.1.2 Plies of roofing felt, 1.1.3 Interply layers of bituminous material, and 1.1.4 Top coating, if present, before any surfacing aggregate has been applied. 1.2 This practice is applicable to both 914 mm [36 in.] and 1000 mm [393⁄8 in.] wide felt rolls. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Analysis of Built-Up Roof Systems During Application

T/CXY 0010-2022 强力瓷砖胶

本文件规定了陶瓷砖胶粘剂的术语和定义、一般要求、要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于陶瓷砖胶粘剂。

Strong Tile Adhesive

T/CBMF 204-2022 地坪行业绿色工厂评价要求

本文件规定了地坪行业绿色工厂评价的总则、评价要求、评价方法及程序、判定和评价报告。 本文件适用于地坪企业的绿色工厂创建与评价。

Requirements for assessment of green factory in floor coatings industry

ASTM D6495/D6495M-18(2022) 土工合成粘土衬里验收试验要求的标准指南

1.1 This guide covers guidelines for the acceptance testing requirements for geosynthetic clay liner (GCL) materials, describing types of tests, test methods, and recommended verifications. 1.2 This guide is intended to aid purchasers, installers, contractors, owners, operators, designers, and agencies in establishing a minimum level of effort for product acceptance testing and verification. This is intended to ensure that the supplied GCL rolls meet accepted material specifications. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this guide means only that the guide has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners

ASTM D3909/D3909M-22 矿物颗粒表面的沥青卷材屋顶（玻璃毡）

1.1 This specification covers asphalt-impregnated and coated glass felt roll roofing surfaced on the weather side with mineral granules, for use as a cap sheet in the construction of built-up roofs. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

ASTM E1612/E1612M-94(2022) 建筑物和停车场结构的预制建筑压缩密封标准规范

1.1 This specification covers the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures. The preformed architectural compression seal is a rectangular elastomeric extrusion, having an internal baffle system produced continuously and longitudinally throughout the material. The architectural compression seal functions under compression and is usually chemically bonded in place with an adhesive. NOTE 1—Movement capability is defined in Test Method E1399/ E1399M. 1.2 This specification covers all colors of architectural compression seals. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures

JC/T 942-2022 丁基橡胶防水密封胶粘带

本文件规定了丁基橡胶防水密封胶粘带（以下简称“丁基胶粘带”）的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于建筑防水工程中接缝密封用丁基胶粘带。 本文件规定的丁基胶粘带适用于高分子防水卷材、水泥混凝土及砂浆、金属板等基材。

Butyl Rubber Waterproof Sealing Adhesive Tape

JC/T 482-2022 聚氨酯建筑密封胶

本文件规定了聚氨酯建筑密封胶的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以氨基甲酸酯聚合物为主要成分的单组分和多组分聚氨酯建筑密封胶。

Polyurethane building sealant

JC/T 483-2022 聚硫建筑密封胶

本文件规定了聚硫建筑密封胶的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以液态聚硫橡胶为基料的室温硫化多组分建筑密封胶。 本文件不适用于中空玻璃二道密封用聚硫密封胶。

polysulfide building sealant

KS F 2368-2022 沥青和波特兰水泥混凝土路面接缝和裂缝热涂密封剂和填料的测试方法

Testing method for sealant and filler, hot-applied, for joints and cracks in asphaltic and portland cement concrete pavements

BS ISO 11617:2022 建筑和土木工程密封剂 测定静态固化样品暴露于人工风化和机械循环后弹性防风雨密封胶的内聚力和外观变化

1   Scope This document specifies laboratory exposure procedures for determining the effects of cyclic movement and artificial weathering on cured, elastic weatherproofing joint sealants (one- or multi-component).

Building and civil engineering sealants. Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering and mechanical cycling

T/CABEE 039-2022 建筑外围护结构缝隙用气密性膜系统 技术规程

本技术规程适用于民用建筑工程中外围护结构缝隙处的气密性膜系统设计、施工和验收。《规程》明确了膜系统的定义，重点研究了膜系统关键性能，提出了技术指标，完善了膜系统的设计要求、施工工艺和验收方法。

Technical specification for air-tight membrane system for gaps in building envelope

ASTM C1737-22 评估在配施前后温度对气溶胶泡沫密封剂的影响的标准指南

1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures. 1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions. 1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures. 1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing

ASTM D8052/D8052M-22 低斜面屋顶组件空气泄漏定量的标准测试方法

1.1 This test method provides a laboratory technique for determining air leakage in low-sloped membrane roof assemblies under specified negative air pressure differences. 1.2 This test method is intended to measure air leakage of a roof assembly with rooftop penetrations. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Quantification of Air Leakage in Low-Sloped Membrane Roof Assemblies

22/30454331 DC BS EN 17872 用于防水的柔性片材 用于不连续屋顶覆盖物的衬垫 人工老化程序

BS EN 17872 Flexible sheets for waterproofing. Underlays for discontinuous roof coverings. Artificial ageing procedure

22/30454770 DC BS EN 17388-1 用于防水的柔性片材 环保产品声明 用于（屋顶）防水的沥青和合成柔性板材的产品类别规则 第 1 部分：从摇篮到坟墓

BS EN 17388-1. Flexible sheets for waterproofing. Environmental product declaration. Product Category Rules for bituminous and synthetic flexible sheets for (roof) waterproofing - Part 1. Cradle to grave

22/30454773 DC BS EN 17388-2 用于防水的柔性片材 环保产品声明 沥青和合成柔性板材的产品类别规则 第 2 部分：从摇篮到大门的选项

BS EN 17388-2. Flexible sheets for waterproofing. Environmental product declarations. Product Category Rules for bituminous and synthetic flexible sheets - Part 2. Cradle to gate with options

ASTM D6630/D6630M-16(2022) 低坡度隔热屋顶膜组件性能的标准指南

1.1 This guide lists test methods intended to establish a minimum level of performance for insulated roof membrane assemblies, and lists pertinent design guidelines and installation methods in a unified manner. Material tests and evaluations are included with and without roof insulation. 1.2 It is not possible to establish a precise correlation between laboratory tests on roof assemblies and natural weathering due to variations in geographical climate, design, material, and installation. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Low-Slope Insulated Roof Membrane Assembly Performance

ASTM C1489-15(2022) 结构用石灰腻子的标准规范

1.1 This specification covers lime putty products made from hydrated lime or quicklime products. Lime putty is suitable for use in masonry, plaster and stucco applications. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Lime Putty for Structural Purposes

ASTM C1248-22 用接缝密封剂染色多孔基材的标准试验方法

1.1 This test method covers four types of laboratory tests to determine if a joint sealant has a probability of staining a porous substrate (such as marble, limestone, sandstone, granite, or other similar material). The tests are on compressed samples and include (1) storage under standard laboratory conditions, (2) storage in an oven, and (3) exposure in a fluorescent UV/condensation device, and (4) exposure in a xenon arc device. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This standard is similar, but not identical, to ISO 16938-1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Staining of Porous Substrate by Joint Sealants