共找到 1872 条与 粘合料、密封材料 相关的标准,共 125 页
弹性恢复率(%)≥90; 拉伸模量(MPa)23℃≤0.4,-20℃≤0.6; 定伸粘结性无破坏;
Technical regulations for application of two-component modified silicone (MS) sealant
Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method
Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods
Standard Test Method for Microscopical Analysis by Reflected Light and Determination of Mesophase in a Pitch
Standard Test Methods and Practices for Emulsified Asphalts
Standard Practice for Calculating Volume-Temperature Correction For Coal-Tar Pitches
Scope is not provided for this standard
Standard Test Method for Float Test for Bituminous Materials
BS EN 12310-1. Flexible sheets for waterproofing - Part 1. Bitumen sheets for roof waterproofing. Determination of resistance to tearing (nail shank)
BS EN 1848-1. Flexible sheets for waterproofing. Determination of length, width and straightness - Part 1. Bitumen sheets for roof waterproofing
Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane
Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems
Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane
Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures. 1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions. 1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures. 1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing
本规程主要包括:1.总则;2.术语;3.材料;4.设计;5.施工;6.验收;7.检查与维修;附录A;附录B;附录C;附录D。
Technical specification for sealant of prefabricated building
本文件规定了门、窗用包覆式PU发泡密封条(以下简称密封条)的分类、技术要求、试验方法、 检验规则、标志、包装、运输和贮存。 本文件适用于以PE材料包覆PU经发泡熟化后制成的一般门、窗用的密封条。
Covered PU foam sealing strips for doors and windows
Standard Test Method for Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials
Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings
本文件建立一种美缝剂中壬基酚的快速、准确地测定方法,为本领域测试人员提供技术指导,为保护环境和人体健康提供技术支撑。规定了室内陶瓷砖美缝剂中壬基酚含量测定的原理、试剂和材料、仪器和设备、试样制备与保存、测定步骤、结果计算、精密度、其他和试验报告等要求。
Determination of nonylphenol content in indoor ceramic tile beautifying agent by gas chromatography-mass spectrometry
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号