91.120.30 防水 标准查询与下载

T/CECS 603-2019 水性橡胶高分子复合防水材料应用技术规程

本规程共分为7章，主要技术内容包括：总则、术语、基本规定、材料、设计、施工、验收。

Technical specification for application of water based rubber polymer composite waterproof material

ASTM E2266-11(2019) 低层建筑墙体系统防水入侵设计与施工标准指南

Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

T/SDAS 61-2019 FS地下刚性防水应用技术规程

1.0.1 为规范FS地下刚性防水技术系统在地下防水工程的应用，做到技术先进、安全适用、经济合理、保证防水工程质量，制定本规程。 1.0.2 本规程适用于民用与工业建筑地下工程、防护工程、市政工程、隧道、城市轨道交通、地下综合管廊等地下工程防水。 1.0.3 采用FS地下刚性防水技术系统的地下工程设计、施工、验收除应符合本规程要求外，尚应符合国家、行业和山东省现行有关标准的规定。

FS Underground Rigid Waterproof Application Technical Regulations

T/SDAS 62-2019 FS地下刚性防水建筑构造

三、FS地下刚性防水技术系统及材料性能指标 (一)FS地下刚性防水技术系统 由FS101防水砂浆防水层、FS101防水水泥素浆和FS102密 实型防水混凝土及细部构造的柔性防水材料构成了FS地下刚性防水技术系统。系统中所采用的柔性防水材料应符合国家或行业相关的标准要求。   1.技术特点 (1)提高地下防水系统的可靠性和耐久性，可在强化混凝土结构自防水的基础上，提升混凝土的密实性和抗裂性。 (2)缩短施工工期，可不设置找平层及保护层。 (3)防水工程与混凝土工程同步施工。 (4)降低地下防水工程成本。 (5)绿色环保。产品在使用过程中不会产生有害气体和废弃物，对环境、土壤均无污染。 (6)有完善的防水混凝土生产、施工、维护等服务体系做为质量保证。 2.防水等级要求 (1) F102密实型防水混凝土与FS101防水砂浆复合使用可满足规范中“不允许渗水，结构表面无湿渍”的一级防水等  级要求。 (2)采用FS102密实型防水混凝土，可满足规范中二级防水等级要求。

FS underground rigid waterproof building structure

ASTM E1677-19 低层框架建筑墙用空气屏障（AB）材料或组件的标准规范

1.1 This specification covers minimum performances and specification criteria for an air barrier (AB) material or system for framed walls of low-rise buildings. The intended users are purchasers of the AB, specifiers of the AB and regulatory groups. The provisions contained in this specification are intended to allow the user to design the wall performance criteria and increase AB specifications to accommodate a particular climate location, function, or design of the intended building. Air barrier performance and specification minimums were selected with the service life of the building wall in mind. 1.2 This specification focuses on ABs for opaque walls. Other areas of the exterior envelope, such as roofs, floors, and interfaces between these areas are not included in this specification. 1.3 This specification does not address air leakage into the wall cavity, that is, windwashing. No standardized test has been developed that adequately identifies all of the influencing factors and measures the impact of this effect on the wall’s thermal performance. 1.4 The specifications in this standard are not intended to be utilized for energy load calculations and are not based on an expected level of energy consumption. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains only to the test method portion, Annex A1, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Air Barrier (AB) Material or Assemblies for Low-Rise Framed Building Walls

T/SHHJ 000026-2019 聚合物水泥防水涂料

本标准规定了聚合物水泥防水涂料（简称JS防水涂料）的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存

Polymer-modified cement for waterproof membrane

T/SHHJ 000027-2019 聚氨酯防水涂料

本标准规定了聚氨酯防水涂料（以下简称PU防水涂料）的分类和标记、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存

Polyurethane waterproofing coating

T/SHGBC 002-2019 非固化橡胶沥青防水涂料应用技术规程

总则、术语、基本规定、材料、设计、施工、质量验收。

Technical specification for application of non-curable rubber modified asphalt coating for waterproofing

T/ZZB 1122-2019 弹性体改性沥青种植屋面用耐根穿刺防水卷材

本标准规定了弹性体改性沥青种植屋面用耐根穿刺防水卷材的术语和定义、分类和标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于以聚酯毡为胎基，以苯乙烯—丁二烯—苯乙烯（SBS）热塑性弹性体作石油沥青改性剂，两面覆以隔离材料并添加阻根剂所制成的防水卷材。

Styrene butadiene styrene（SBS）modified bituminous waterproofing sheets of resistance to root penetration for green roof

ASTM C1501-19 由实验室加速老化程序确定的建筑结构密封胶的颜色稳定性的标准测试方法

1.1 This test method describes laboratory accelerated weathering procedures using either fluorescent ultraviolet or xenon arc test devices for determining the color stability of building construction sealants. 1.2 Color stability rankings provided by these two procedures may not agree. 1.3 The values stated in SI units are to be regarded as the standard. Values given in parentheses are for information only. 1.4 There is no equivalent ISO standard for this test method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures

T/CBMF 49*T/CWA 301-2019 沥青基耐根穿刺防水卷材阻根剂含量试验方法

本标准规定了沥青基耐根穿刺防水卷材中阻根剂测定的试剂和材料、仪器设备、样品、色谱条件、试验步骤和试验报告。 本标准适用于GB/T 35468-2017中单一化合物类阻根剂和聚合物类阻根剂种类和含量测试。 产品中阻根剂含量试验结果不适用于判定产品的耐根穿刺性能。   

Test method for content of anti-rooting agent in asphalt-based root puncture-resistant waterproofing membrane

ASTM E2321-03(2019) 测定外部绝缘和表面处理系统（EIF）的水蒸气传输（WVT）的试验方法使用的标准实施规程

1.1 This practice describes how to use Test Methods E96/ E96M to determine the water vapor transmission (WVT) characteristics of an EIFS sample. 1.2 An Exterior Insulation and Finish System (EIFS) is a multilayer exterior building wall material that consists of a number of layers. For the purpose of this standard, these layers, whether they be individual EIFS component materials in single layers, or groups of EIFS component materials, are called the “EIFS sample.” 1.3 The Water Method, Procedures B and D described in X1.1.2 and X1.1.5 of Appendix X1 of Test Methods E96/E96M shall be used in this practice. 1.4 This practice is limited to specimens not over 11⁄4 in. (32 mm) in thickness, except as provided in Section 9 of this practice. 1.5 The values stated in inch-pound units are to be regarded as the standard. Metric inch-pound conversion factors for water vapor transmission, permeance, and permeability are stated in Table 1 of Test Methods E96/E96M. All conversions of mm Hg to Pa are made at a temperature of 0 °C. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Use of Test Methods for Determining the Water Vapor Transmission (WVT) of Exterior Insulation and Finish Systems (EIFS)

T/CBMF 43-2019 热塑性聚烯烃（TPO）预铺防水卷材

本标准规定了热塑性聚烯烃（TPO）预铺防水卷材（简称TPO预铺防水卷材）的术语和定义、规格和标记、技术要求、试验方法、检验规则、标志、包装、贮存与运输。 本标准适用于以热塑性聚烯烃（TPO）为主体材料的预铺防水卷材。

Thermoplastic polyolefin (TPO) pre-laid waterproofing membrane

T/CBMF 44-2019 特种非固化橡胶沥青防水涂料

本标准规定了特种非固化橡胶沥青防水涂料（以下简称特种非固化）的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于非外露防水工程用特种非固化橡胶沥青防水涂料。

Specialty waterproofing coating with non-curable rubber modified asphalt

KS F 4925-2018(英文版) 水泥砂浆掺液体防水剂

Cement mortar mixed liquid waterproofing agent

KS F 4925-2018 水泥砂浆混合流动性止水剂

Cement mortar mixed liquid waterproofing agent

KS F 4938-2018(2023) 根部穿透阻力的标准试验方法

Standard test method for root penetration resistance

KS F 9004-2018 防水层保护用预制膨胀缝填充混凝土的标准规范

Standard specification of performed expansion joint filler concrete of slab for protection of waterproofing layer

KS F 4938-2018 对于以防水 阻根材料的根系穿透阻力绿色屋顶系统试验方法

Standard test method for root penetration resistance

KS F 2622-2018 薄膜屋面系统性能评定的标准试验方法

Standard test method for performance evaluation of membrane roofing systems