91.120.30 防水 标准查询与下载

JC/T 2254-2014 喷涂聚脲用层间处理剂

本标准规定了喷涂聚脲用层间处理剂(简称JN处理剂)的标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于喷涂聚脲涂料超过规定复涂时间再次施工时,对原聚脲防水层复涂面进行涂覆的处理剂。

Lapping adhesive for spray polyurea layer agents

JC/T 2252-2014 喷涂聚脲用底涂和腻子

本标准规定了喷涂聚脲用底涂和腻子的标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于喷涂聚脲防水工程中水泥砂浆和混凝土基面用底涂和腻子。

Primer and putty for spray polyurea coating

JC/T 2253-2014 脂肪族聚氨酯耐候防水涂料

本标准规定了脂肪族聚氨酯耐候防水涂料(简称APU耐候防水涂料)的术语和定义、标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于防水工程中外露使用的脂肪族聚氨酯耐候防水涂料。

Aliphatic polyurethane weathering waterproof coating

JC/T 2251-2014 聚甲基丙烯酸甲酯(PMMA)防水涂料

本标准规定了聚甲基丙烯酸甲酯(PMMA)防水涂料的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于建设工程防水用反应型聚甲基丙烯酸甲酯涂料。

Polymethyl methacrylate coating for waterproofing

JC/T 2237-2014 无震动防滑车道用聚合物水泥基材料

本标准规定了无震动防滑车道用聚合物水泥基材料(简称防滑车道用材料)的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于无震动防滑车道用聚合物水泥基材料。

Polymer modified cementitious material for anti-vibration and skidding lane

JC/T 2273-2014 硅烷/硅氧烷建筑防护剂中有效成分含量及有害物质测定方法

本标准规定了硅烷/硅氧烷建筑防护剂中有效成分和有害物质测定的术语和定义、试验方法和试验报告。本标准适用于硅烷/硅氧烷建筑防护剂中硅烷和硅氧烷有效成分的测定。本标准适用于硅烷/硅氧烷建筑防护剂中甲醇、苯、甲苯、乙苯和二甲苯总和、挥发性有机化合物、水溶性氯离子等有害物质的测定。

Standard test methods for determination of effective component and harmful substances in silane/siloxane building protecting agents

DB11/T 1106-2014 建筑墙体砌块结构自保温施工和验收规程

Rules for self-insulation construction and acceptance of building wall block structure

JC/T 2217-2014 环氧树脂防水涂料

本标准规定了环氧树脂防水涂料(简称EP防水涂料)的术语和定义、标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于建设工程非外露使用的环氧树脂防水涂料。

Epoxy resin waterproof coating

JC/T 2218-2014 防水卷材沥青技术要求

本标准规定了用于防水卷材用沥青的分类、技术要求和试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于以天然石油经蒸馏、氧化或调配等工艺制得的,用于生产改性沥青防水卷材、自粘改性沥青防水卷材的石油沥青。

Technical requirement for asphalt used in waterproofing sheet

GSO ASTM E2266:2014 低层结构墙系统抗渗水设计和施工的标准指南

1.1 This guide describes design, specification, selection, installation, and inspection of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints of wood and metal frame buildings, typically four stories or less, to minimize water intrusion. 1.2 This guide does not address prevention of damage caused by water originating from the use of wet building materials or from indoor or outdoor humidity.Water from these sources can be important, and the potential for damage caused by water from these sources must not be overlooked in building design or construction. 1.3 This guide does not address roofing systems, except when the surface of a deck also serves as a roof and at locations where roof systems interface with building walls. 1.4 This guide does not address any type of barrier wall system. 1.5 This guide does not address any exterior insulation and finish system (EIFS). 1.6 This guide does not address foundation conditions where the bottom of a slab on grade or the grade of a crawl space is at or below the water table or subject to hydrostatic pressure. 1.7 This guide is intended to supplement and not duplicate building code requirements. 1.8 Maintenance, although important, is not covered in detail. 1.9 Application of finishes, such as paint and sealers, may be important in the performance of some types of cladding; however, this is not covered in detail. 1.10 This guide applies only to constructions with sheathing, which facilitates installation of the weather-resistive barrier and associated flashings in a common plane. 1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.12 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

DB21/T 2249-2014 沥青类防水卷材接缝剥离强度现场快速检测方法

On-the-spot rapid detection method of seam peel strength of asphalt waterproof membrane

BS 8582:2013 开发场所地表水管理惯例

This British Standard gives recommendations on the planning, design, construction and maintenance of surface water management systems for new developments and redevelopment sites in: a)minimizing and/or mitigating flooding and other environmental risks arising from: 1)site surface water run-off as a result of rain falling onto the development site; 2)run-off conveyed across or arising on the site from other sources. NOTE 1 Run-off resulting from snow melt is not covered in this British Standard. b)maximizing the societal and environmental benefits arising from the: 1)use of surface water run-off to protect and enhance local water resources and supplies; 2)contribution of surface water management systems in mitigating climate risks associated with urbanization; 3)integration of surface water management systems with urban design in delivering amenity and community value and in repairing, protecting and enhancing landscape and/or townscape character; 4)repair, protection and enhancement of biodiversity.

Code of practice for surface water management for development sites

ASTM E2485/E2485M-13 外部绝缘和表面处理系统（EIFS）和防水屏障涂层的冷冻/抗冻性的标准测试方法

5.1 Resistance to freezing and thawing is a factor when determining the durability of EIFS, an EIFS with water-resistive barrier coatings, and water-resistive barrier coatings by itself. 1.1 This test method covers procedures for determining the effect of freezing and thawing of exterior insulation and finish systems (EIFS), an EIFS with water-resistive barrier coatings, and water-resistive barrier coatings by itself. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Freeze/Thaw Resistance of Exterior Insulation and Finish Systems (EIFS) and Water Resistive Barrier Coatings

DB11/ 358-2013 烟花爆竹安全 级别、类别和标识标注

Safety level, category and labeling of fireworks and firecrackers

DS/EN 14909:2013 防水用柔性板材 塑料和橡胶防潮层 定义和特性

This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the produc

Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics

DS/EN 13984:2013 防水用柔性板材 塑料和橡胶蒸汽控制层 定义和特性

This European Standard specifies the characteristics of flexible sheets of plastic or rubber intended for use as water vapour control layers for buildings and applies to both reinforced and unreinforced products. It specifies requirements and test methods

Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics

DB13/T 1696-2013 热塑性聚烯烃（TPO）自粘复合防水卷材

本标准规定了热塑性聚烯烃（TPO）自粘复合防水卷材的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、贮存和运输。本标准适用于热塑性聚烯烃（TPO）自粘复合防水卷材。

Thermoplastic polyolefin (TPO) self-adhesive composite waterproof membrane

JC/T 2158-2012 渗透型液体硬化剂

本标准规定了渗透型液体硬化剂的要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于能渗入水泥基地面面层，起到密实作用的以无机材料为主的单组份渗透型液体硬化剂。

Liquid concrete densifer

JC/T 645-2012 三元丁橡胶防水卷材

本标准规定了三元丁橡胶防水卷材（简称三元丁卷材）的术语和定义、分类、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于三元丁橡胶防水卷材。

Waterproofing sheet made from reclaimed rubber

JC/T 2112-2012 塑料防护排水板

本标准规定了塑料防护排水板（简称排水板）的分类和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、贮存和运输等。 本标准适用于以聚乙烯、聚丙烯等树脂为主要原材料，表面呈凹凸形状，用于种植屋面、地下建筑、隧道等工程的塑料防护排水板。 其他材质和用途的防护排水板也可参照本标准使用。

Plastic board for drainage and protection