93.140 航道和港口建筑 标准查询与下载

DB41/T 2266-2022 水运工程工地建设规范

Water transportation engineering site construction specifications

DB34/T 5037-2022 船闸工程施工安全检查标准

Construction safety inspection standards for ship lock engineering

DB33/T 2449-2022 高桩码头大中修工程质量检验评定规范

Specifications for quality inspection and assessment of high-pile wharf major and medium repair projects

DB32/T 4193-2022 工业化装配式箱型护岸质量检验规程

本文件适用于江苏省内河航道工业化装配式箱型护岸建设的工程质量检验。

Quality inspection regulations for industrialized assembled box-type revetment

DB32/T 4191-2022 江苏省绿色航道建设指南

本指南适用于指导江苏省境内内河（不含长江）绿色航道工程的设计、施工和养护。

Guidelines for the construction of green waterways in Jiangsu Province

ASTM D6092-21 侵蚀控制用石材标准尺寸规定的标准实施规程

1.1 This practice covers size designations and maximum ranges in mass or gradation for standard sizes for riprap, spalls, or bedding, or both, used for slope protection of dam embankments, streambank erosion control, bridge piers and abutments. Sizes used for outer harbor structures such as breakwalls, revetments, confined diked disposal structures (heretofore described as armor stone, cover stone, or dimension stone) for which stone sizes range between 5 and 25 tons, or that require cut dimensions for layed-up structures are beyond the scope of this practice. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are rationalized conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This practice offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Specifying Standard Sizes of Stone for Erosion Control

T/JSJTQX 18-2021 江苏省内河船闸维护潜水作业规程

将多年来的船闸潜水作业的成熟经验进行固化和优        化后制定的规范性标准，规范对船闸潜水作业的流程，潜水作业的环境、人员、作业方法等全面的分解，提出具体要求。规程是船闸潜水作业的指南，对船闸的水下潜水作业有较强的指导意义，进一步提高潜水作业的效率和安全性。

Diving operation regulations for maintenance of inland river lock in Jiangsu Province

T/JSJTQX 17-2021 江苏交通船闸门机电检测通则

       将京杭运河江苏省交通运输厅苏北航务管理处多年来的船闸综合检测、船闸大修检测的成熟经验进行固化和优化，并结合目前国内船闸门机电设施的检测现状，严格按照标准的广泛适用性和普遍指导性，相对先进性和经济合理性，要求的全面性和可操作性来推进。起草工作组讨论了当前国内外相关标准的适用情况，确定了标准起草的总体框架和主要内容。

General requirements for electromechanical detection of Jiangsu traffic electrical gate

DB32/T 3973-2021 交通船闸大修工程质量检验规范

Specifications for quality inspection of traffic ship lock overhaul engineering

DB32/T 3974-2021 交通船闸维护技术规范

Technical specification for maintenance of traffic locks

DB34/T 3678-2020 内河航道疏浚工程施工技术规程

Construction technical regulations for dredging engineering of inland waterway

DB34/T 978-2020 高桩码头施工安全检查标准

Construction safety inspection standards for high-piled wharves

DB34/T 3586-2020 船闸工程施工技术规程

Construction technical regulations for ship lock engineering

ASTM F2766-11(2020) 船闸的标准试验方法

1.1 This test method is intended to provide a means of evaluating the performance of Boat Barriers and through that evaluation provide a certification of performance in the form of an ASTM International Impact Rating for Boat Barriers to be used in the design and specification of Boat Barriers. In addition to the Impact Rating, testing under this standard requires the determination and reporting of the maximum deformation of the barrier during testing to further aid in appropriate barrier selection. 1.2 This test method provides a range of small surface motor boat impact condition levels and penetration performance levels to select boat barriers appropriate for use at potentially threatened onshore port facilities, offshore facilities, and floating assets. 1.3 This test method is designed to test and evaluate the stopping capabilities of boat barriers at the point of impact and the moments subsequent to impact of a small surface motor boat. 1.4 This test method is not intended to be used for the testing criteria of floating “lines of demarcation” or similar items or technologies that do not make claims of “boat or small surface motor boat” stopping capabilities. 1.5 Governing agencies may adopt those performance levels in this test method that satisfy their specific needs and assign certification ratings for small surface motor boat stopping barriers based on the tests and test methodologies described in this test method. 1.6 Many test parameters are standardized to arrive at common small surface motor boat types and masses, enhance test realism and replications, and produce uniform rating designations. 1.6.1 Compliance with these rating designations establishes a measure of performance but does not render any boat barrier invulnerable to motor boat penetration. Caution should be exercised in interpreting test findings and projecting results to other hypothetical conditions. 1.7 Product design/certification in this test method only addresses the ability of the barrier to withstand the impact of the test motor boat. It does not represent an endorsement of the product/design or address its operational suitability. 1.8 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Boat Barriers

T/HB 0003-2020 遥测遥控LED桥梁实时净高显示标志 技术要求

本标准规定了航道中桥梁实时净高LED显示标志的分类、型号和工况条件，组成、布局、形状和尺寸。

Technical requirements for real-time net height display signs of telemetry and remote control LED bridges

T/JSJTQX 11-2020 驳岸墙移动模架施工指南

本指南主要应用于航道、港口、水利等工程，重点阐述“驳岸墙移动模架”在工程施工中应用的成熟工艺、先进技术和管理重点，强调了施工过程和关键工序的控制。结合行业现状，本指南分别从“整体式移动模架”、“分体式移动模架”两种主流工艺，明确了模架的设计、模架的制作与安装、模架的使用、模架的拆除与维养等方面提出具体要求。

Construction Guide for Movable Formwork Frame of Barge Wall

DB21/T 3215-2019 水运工程混凝土结构冲击弹性波法检测技术规程

Technical regulations for the detection of concrete structures in waterway engineering by shock elastic wave method

DB45/T 1828-2018 海港工程混凝土材料与结构耐久性定量设计规范

Quantitative Design Code for Durability of Concrete Materials and Structures in Harbor Engineering

ASTM F1244-08(2018) 船用泊位标准规范

1.1 This specification covers the construction of marine berths for officers, crew, and passengers. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Berths, Marine

ASTM A690/A690M-13a(2018) 用于海洋环境的具有耐大气腐蚀性的高强度低合金镍 铜 磷钢H桩和板桩的标准规范

1.1 This specification covers high-strength low-alloy nickel, copper, phosphorus steel H-piles and sheet piling of structural quality for use in the construction of dock walls, sea walls, bulkheads, excavations, and like applications in marine environments. 1.2 The atmospheric corrosion resistance of this steel is substantially better than that of ordinary carbon steels with or without copper addition (see Note 1). The steel has also shown to have substantially greater resistance to seawater “Splash Zone” corrosion than ordinary carbon steel (Specifications A36/A36M and A328/A328M) where exposed to the washing action of rain and the drying action of the wind or sun, or both. Where the steel is not boldly exposed, the usual provisions for the protection of ordinary carbon steel should be considered. NOTE 1—For methods of estimating atmospheric corrosion resistance of low-alloy steels, see Guide G101. 1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.4 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High-Strength Low-Alloy Nickel, Copper, Phosphorus Steel H-Piles and Sheet Piling with Atmospheric Corrosion Resistance for Use in Marine Environments