C70 工业防尘防毒技术 标准查询与下载

AQ 4226-2012 城镇燃气行业防尘防毒技术规范

本标准规定了城镇燃气输配和供应系统中的防尘防毒技术措施和要求。 本标准适用于向城市、乡镇或居民点供给居民生活、商业、工业企业生产、采暖通风和空调等各类用户作为燃料使用的城镇燃气运营维护系统中粉尘和毒物危害控制的工程技术和管理。焦化厂、天然气净化厂等燃气生产系统的粉尘和毒物危害控制可参照本标准。

Technical specification of dust and poison control for city gas industry

AQ 4225-2012 印刷企业防尘防毒技术规范

本标准规定了印刷企业的防尘防毒的技术要求、措施和管理。 本标准适用于书、报、刊印刷，本册印制，包装装潢等印刷企业（以下简称印刷企业）的防尘防毒的设计、布局和管理，也适用于职业危害监督管理部门对印刷企业的监管。

Technical code of dust and poison control for printing enterprise

AQ 4224-2012 仓储业防尘防毒技术规范

本标准规定了仓储业防尘防毒的技术要求和管理措施。 本标准适用于储存各类物品的库房、货场、货棚、储罐等作业过程中粉尘、毒物危害控制的工程技术和管理，也适用于相关部门对仓储作业过程中粉尘、毒物危害的监督。

Guidelines of dust and poison prevention and control for warehousing trade

AQ/T 4219-2012 焦化行业防尘防毒技术规范

本标准规定了焦化企业的有关防尘防毒的技术要求、措施和管理。 本标准适用于焦化企业生产过程中粉尘、毒物危害的工程技术和管理防范。

Technical specification of dust and poison control for coking industry

AQ/T 4218-2012 铝加工厂防尘防毒技术规程

本标准规定了铝加工厂防尘防毒的设计要求、技术措施和管理。 本标准适用于铝加工厂防尘防毒的工程设计、铝加工厂生产过程的防尘防毒技术和管理。

Code of dust and poison control for aluminium processing enterprises

AQ 4217-2012 粉尘采样器技术条件

本标准规定了粉尘采样器的技术要求、试验方法、标志、包装、运输和贮存等。 本标准适用于作业场所定点采集空气中总粉尘和呼吸性粉尘的采样器，不适用于个体粉尘采样器。 本标准适用于粉尘采样器生产企业，并对使用单位正确选用有指导作用。

Technical requirements for dust sampler

ISO 15202-2:2012 工作场所空气 用感应耦合等离子发射光谱法测定空气中悬浮颗粒物质中的金属和类金属物 第2部分：样品的制备

Workplace air - Determination of metals and metalloids in airborne particulate matter by inductively coupled plasma atomic emission spectrometry - Part 2: Sample preparation

BS EN 1540:2011 工作场所暴露.术语

Workplace exposure. Terminology

ANSI/NFPA 473-2012 处理危险材料/大规模杀伤性武器(WMD)事故的EMS人员应变能力标准

1.1 Scope. This standard identifies the levels of competence required of emergency medical services (EMS) personnel who respond to incidents involving hazardous materials or weapons of mass destruction (WMD). It specifically covers the requirements for basic life support and advanced life support personnel in the pre-hospital setting. 1.1.1 This standard is based on the premise that all EMS responders are trained to meet at least the core competencies of the operations level responders as defined in Chapter 5 of NFPA 472, Standard for Competence of Responders to Hazardous Materials/Weapons of Mass Destruction Incidents.

Standard for Competencies for EMS Personnel Responding to Hazardous Materials/Weapons of Mass Destruction Incidents

ANSI N13.56-2012 工作场所中核设施气载放射性释放的取样和监测

Sampling and Monitoring Releases of Airborne Radioactivity in the Workplace of Nuclear Facilities

ASTM D7773-12 用滤波器采样和抑制型离子色谱法测定挥发无机酸(氯化氢,溴化氢和次硝酸)的标准试验方法

Exposure to inorganic acids in workplace air can cause irritations of the skin, eyes and respiratory tract, and exposure limits for hydrochloric acid, hydrobromic acid and nitric acid in air have been established to reduce exposure risks to potentially affected workers (1). Sampling and analytical methods for volatile inorganic acids are needed for exposure assessment and risk reduction purposes.1.1 This test method is intended for use in the determination of the time-weighted average mass concentration of hydrogen chloride gas and hydrochloric acid mist, hydrogen bromide vapor and hydrobromic acid mist, and nitric acid vapor and mist in workplace air. The samples are collected on an alkali-impregnated quartz fiber filter and analyzed by ion chromatography. The method is also appropriate for measuring short term exposures. 1.2 This test method assumes that air samples are collected using appropriate and applicable ASTM International standards for sampling of workplace air. 1.3 The procedure is targeted for occupational and environmental hygiene monitoring purposes. 1.4 No detailed operating instructions are provided because of differences among various makes and models of suitable instruments. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. This standard does not address comparative accuracy of different devices or the precision between instruments of the same make and model. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 The practice contains notes, which are explanatory and not part of mandatory requirements of the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Volatile Inorganic Acids (HCl, HBr, and HNO3 ) Using Filter Sampling and Suppressed Ion Chromatography

ASTM D3824-12 用化学发光法连续测定周围环境或工作场所空气中氮的氧化物含量的标准试验方法

Most oxides of nitrogen are formed during high-temperature combustion. The Environmental Protection Agency (EPA) has set primary and secondary air quality standards for NO2 that are designed to protect the public health and the public welfare (40 CFR, Part 50). Oxides of nitrogen are generated by many industrial processes that can result in employee exposures. These are regulated by the Occupational Safety and Health Administration (OSHA) which has promulgated exposure limits for the industrial working environment (29 CFR, Part 1910). These methods have been found satisfactory for measuring oxides of nitrogen in the ambient and workplace atmosphere over the ranges shown in 1.1.1.1 These test methods cover procedures for the continuous determination of total nitrogen dioxide (NO2) and nitric oxide (NO) as NOx, or nitric oxide (NO) alone or nitrogen dioxide (NO2) alone, in the ranges shown in the following table: Range of Concentration GasAmbient AtmosphereWorkplace Atmosphere μg/m3 (ppm) (Note 1)mg/m3 (ppm) (Note 1) NO10 to 600 (0.01 to 0.5)0.6 to 30 (0.5 to 25) (NO + NO2) = NOx20 to 1000 (0.01 to 0.05)1 to 50 (0.5 to 25) NO220 to 1000 (0.01 to 0.5)1 to 50 (0.5 to 25) Note 18212;Approximate range: 25°C and 101.3 kPa (1 atm). 1.2 The test methods are based on the chemiluminescent reaction between nitric oxide and ozone. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9.

Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method

ISO/TR 14294:2011 工作场所环境.皮肤暴露度测量原则和方法

Workplace atmospheres - Measurement of dermal exposure - Principles and methods

AQ 4213-2011 煤层气开采防尘防毒技术规范

本标准规定了煤层气开采企业防尘防毒技术的技术要求、措施和管理。 本标准适用于煤层气开采企业在进行地面和井下煤层气开采过程中防治粉尘、毒物危害的工程技术和管理工作，安全生产监督管理部门和职业病危害监督管理部门对煤层气开采企业生辰过程中防治粉尘、毒物危害工作的监督。

Technology code of dust and poison control for coal bed methane exploitation

AQ/T 4216-2011 钢铁冶炼企业职业健康管理技术规范

本标准规定了钢铁冶炼企业职业健康管理的基本要求和技术措施，钢铁冶炼企业包括球团、烧结、炼铁、炼钢等生产企业。 本标准适用于钢铁冶炼工作场所和建设项目职业危害（不含电离辐射）防护设计、职业健康管理、评价与监督。

Technical code on occupational health management for the steel and iron smelting enterprises

AQ 4214-2011 焊接工艺防尘防毒技术规范

本标准规定了焊接工艺防尘防毒的技术要求和管理措施。 本标准适用于焊接工艺过程中粉尘、毒物危害控制的工程技术和管理，也适用于相关部门对焊接工艺过程中粉尘、毒物危害的监测。

Guidelines of dust and poison prevention and control

AQ/T 4212-2011 氧化铝厂防尘防毒技术规程

本标准规定了氧化铝厂防尘防毒的设计要求、技术措施和管理。 本标准适用于氧化铝厂防尘防毒的设计、布局和施工，氧化铝厂生产防尘防毒相关的技术和管理。

Regulations for dust and poison control of alumina refinery

DIN EN ISO 28439:2011 工作场所环境.极细微气溶胶/纳米气溶胶特征描述.利用微分电气流动分析系统进行粒度分布和计数浓度测定(ISO 28439-2011).德文版本EN ISO 28439-2011

This International Standard provides guidelines for the determination of number concentration and the size distribution of ultrafine aerosols and nanoaerosols by use of mobility particle sizers (also called differential mobility analysers). Only the particle fraction of the aerosol is considered. For ultrafine aerosols and nanoaerosols, exposure metrics such as the number and surface area concentration are important. This International Standard also gives guidelines for the determination of workplace exposure to ultrafine aerosols and nanoaerosols.

Workplace atmospheres - Characterization of ultrafine aerosols/ nanoaerosols - Determination of the size distribution and number concentration using differential electrical mobility analysing systems (ISO 28439:2011); German version EN ISO 28439:2011

NF X43-133*NF EN ISO 28439:2011 工作场所大气.超细悬浮微粒/毫微悬浮颗粒表征.使用微分迁移率分析系统测定粒度分布和计数浓度.

Workplace atmospheres - Characterization of ultrafine aerosols/nanoaerosols - Determination of the size distribution and number concentration using differential mobility analysing systems.

BS DD CEN/TS 16115-1:2011 环境空气质量.生物气溶胶的测量.使用过滤器抽样系统和培养基分析的霉菌测定

This Technical Specification describes the measurement of moulds in ambient air in order to identify, quantify and characterize bioaerosol pollution in ambient air resulting from emissions from different sources. The method described specifies the sampling of moulds as part of the suspended particulate matter (SPM, here particles with aerodynamic diameter up to ca. 30 μm) using a filter sampling system with gelatine/polycarbonate filter combination followed by the culture-based analyses on DG18 agar. The sampling duration can be varied between 10 min to 24 h. The health effect of bioaerosols is not limited to any particle fraction, therefore, this document describes the sampling of moulds as part of the suspended particulate matter as a convention method. NOTE The sampling method described in this document in principle is likely to be appropriate for the sampling of actinomycetes and other spore-forming bacteria (resistant to desiccation). For these species a special analytical procedure using different culture media should be applied, but this is not within the scope of this document. The standard method set out in this Technical Specification is accepted by convention as reference method. The measured quantity, here the number of colony forming units per cubic meter (CFU/m), is determined by the inlet design of the sampling head, the associated operational parameters and the analytical procedure. Standardized methods for sampling, detection and enumeration of moulds including standards for sampling strategies are important for comparative assessment of moulds in ambient air. Before doing any measurements a plan for the measurement strategy is necessary (see CEN/TS 16115-2 [5]). WARNING — The use of this Technical Specification may involve hazardous materials, operations and equipment. This Technical Specification does not purport to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Ambient air quality. Measurement of bioaerosols. Determination of moulds using filter sampling systems and culture-based analyses