E91 石油物探测井设备与仪器 标准查询与下载

SY/T 6743-2008 自然伽马测井仪校准方法

本标准规定了自然伽马测井仪的校准方法。 本标准适用于新制造、使用中和修理后的自然伽马测井仪的校准。

The calibration method of gamma-ray tool

ISO 10416:2008 石油和天然气工业.钻井液.实验室试验

This International Standard provides procedures for the laboratory testing of both drilling fluid materials and drilling fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or "make-up" fluid. It is not applicable as a detailed manual on drilling fluid control procedures. Recommendations regarding agitation and testing temperature are presented because the agitation history and temperature have a profound effect on drilling fluid properties.

Petroleum and natural gas industries - Drilling fluids - Laboratory testing

SY/T 5099-2007 石油测井仪器环境试验及可靠性要求

本标准规定了石油测井仪器的环境试验及可靠性要求、试验方法。 本标准适用于石油测井仪器的设计、制造及质量评价。

Environmental test and reliability requirements for petroleum well-logging instruments

SY/T 5391-2007 石油地震数据采集系统

本标准规定了陆用有线传输地震数据采集系统（以下简称仪器）的组成、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于仪器的制造、检验和质量评价。

Petroleum seismic data acquisition system

SY/T 5419-2007 石油测井中子发生器及中子管技术条件

本标准规定了石油测井中子发生器及中子管（以下简称为产品）的技术要求，试验方法，检验规则，标志、包装、运输和贮存，安全和环境保护。 本标准适用于石油测井中子发生器及中子管的设计、制造、应用、检验和质量评价。

Technical specifications of neutron generator and neutron tube for petroleum well logging

SY/T 6674-2006 密度测井刻度器校准方法

本标准规定了石油测井领域中的补偿密度测井仪和岩性密度测井仪的刻度器的校准方法，适用于采用脊肋图法确定密度及采用拟合方法确定光电吸收系数的密度测井仪刻度器的校准。

The transformation method of density logging calibrator

SY/T 6642-2006 井间地震成像系统

本标准规定了采用加速重锤脉冲震源的井间地震成像系统（以下简称产品）的组成、要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于产品的制造、检验和质量评价。

Cross well seismic data imaging system

ISO 15136-2:2006 石油和天然气工业.人工升降机用推进腔体泵系统.第2部分:表面传动系统

This part of ISO 15136 provides requirements for the design, design verification and validation, manufacturing and data control, performance ratings and repair of progressing cavity pump surface-drive systems for use in the petroleum and natural gas industry. This part of ISO 15136 is applicable to those products meeting the definition of surface-drive systems. Additionally, informative annexes provide information on brake system selection, installation, and operation; and sucker rod selection and use. Equipment not covered by this part of ISO 15136, unless integral by design, includes bottom drive systems, sucker rods, polished rod clamps, stuffing boxes, electrical controls, instrumentation, external power transmission devices, auxiliary equipment, such as belts, sheaves and equipment guards. These items might or might not be covered by other International Standards.

Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems

DIN EN ISO 13503-3:2006 石油和天然气工业.完井液和材料.第3部分:重盐水的试验(ISO 13503-3:2005)

This International Standard contains the testing of heavy brines.

Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines (ISO 13503-3:2005); English version EN ISO 13503-3:2005

DIN EN ISO 16070:2006 石油和天然气工业.下井设备.锁芯轴和落地接头

This International Standard provides the requirements for lock mandrels and landing nipples within the production/injection conduit for the installation of flow control or other equipment used in the petroleum and natural gas industries. It includes the interface connection to the flow control or other equipment, but does not cover the connections to the well conduit.#,,#

Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005); English version EN ISO 16070:2005

NF M87-272-3*NF EN ISO 13503-3:2006 石油和天然气工业.完井液和材料.第3部分:重盐水的试验

Petroleum and natural gas industries - Completion fluids and materials - Part 3 : testing of heavy brines.

BS EN ISO 16070:2006 石油和天然气工业.下降孔设备.锁紧芯轴和落地螺纹接头

ISO 16070:2005 provides the requirements for lock mandrels and landing nipples within the production/injection conduit for the installation of flow control or other equipment used in the petroleum and natural gas industries. ISO 16070:2005 includes the interface connections to the flow control or other equipment, but does not cover the connections to the well conduit.

Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples

ISO 13500:2006 石油和天然气工业.钻井液体材料.规范和测试

This International Standard covers physical properties and test procedures for materials manufactured for use in oil- and gas-well drilling fluids. The materials covered are barite, haematite, bentonite, nontreated bentonite, OCMA grade bentonite, attapulgite, sepiolite, technical grade low-viscosity carboxymethylcellulose (CMC-LVT), technical grade high-viscosity carboxymethylcellulose (CMC-HVT), and starch. This International Standard is intended for the use of manufacturers of named products.

Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests

BS EN ISO 13503-3:2005 石油和天然气工业.完井液和材料.重盐水试验

ISO 13503-3:2005 covers the physical properties, potential contaminants and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion and workover fluids. ISO 13503-3:2005 provides methods for assessing the performance and physical characteristics of heavy brines for use in field operations. It includes procedures for evaluating the density or specific gravity, the clarity or amount of particulate matter carried in the brine, the crystallization point or the temperature (both ambient and under pressure) at which the brines make the transition between liquid and solid, the pH, and iron contamination. It also contains a discussion of gas hydrate formation and mitigation, brine viscosity, corrosion testing, buffering capacity and a standardised reporting form. ISO 13503-3:2005 is intended for the use of manufacturers, service companies and end-users of heavy brines.

Petroleum and natural gas industries - Completion fluids and materials - Testing of heavy brines

ISO 16070:2005 石油和天然气工业.下井设备.锁芯轴和落地接头

This International Standard provides the requirements for lock mandrels and landing nipples within the production/injection conduit for the installation of flow control or other equipment used in the petroleum and natural gas industries. It includes the interface connections to the flow control or other equipment, but does not cover the connections to the well conduit.

Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples

SY/T 6625-2005 成像测井地面仪通用技术条件

本标准规定了成像测井地面仪（以下简称仪器）的组成、要求、试验方法、检验规则以及标志、标签、包装、运输和贮存。 本标准适用于仪器的设计、制造及质量评价。

General requirements of imaging logging surface system

SY/T 5046-2005 地震检波器

本标准规定了电磁感应类地震检波器（以下简称检波器）的组成、型式和分类、要求、试验方法、检验规则以及标志、包装、运输、贮存。 本标准适用于检波器的制造、检验及质量评估。

Seismic geophone

SY/T 6624-2005 工程地震仪

本标准规定了工程地震仪（以下简称仪器）的原理、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于仪器的制造、检验和质量评价。

Engineering seismic instrument

BS EN ISO 10427-3:2004 石油和天然气工业.固井用设备.浮动式固井设备的性能试验

ISO 10427-3:2003 describes testing practices to evaluate the performance of cementing float equipment for the petroleum and natural gas industries. ISO 10427-3:2003 is applicable to float equipment that will be in contact with water-based fluids used for drilling and cementing wells. It is not applicable to float equipment performance in non-water-based fluids.

Petroleum and natural gas industries - Equipment for well cementing - Performance testing of cementing float equipment

SY/T 5524-2004 石油地震勘探钻机车

本标准规定了石油地震勘探钻机车的型式、型号、基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于用二类底盘或整车改装的石油地震勘探、工程物探、水文勘探、金属及非金属矿藏勘探、化探用钻机车的生产、制造和验收。

Oil seismic exploration drilling rig