E97 油、气处理设备 标准查询与下载

ISO 15547-2:2005 石油、石化和天然气工业.板式热交换器.第2部分:铜焊铝板热交换器

This part of ISO 15547 gives requirements and recommendations for the mechanical design, materials selection, fabrication, inspection, testing, and preparation for shipment of brazed aluminium plate-fin heat exchangers for use in petroleum, petrochemical and natural gas industries.

Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers

ISO 13706:2005 石油、石化和天然气工业.风冷热交换器

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum and natural gas industries. This International Standard is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.

Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers

SY/T 0602-2005 甘醇型天然气脱水装置规范

本标准阐述了以三甘醇作为吸收剂的常规甘醇型天然气脱水装置（以下简称脱水装置）的材料、设计、制造和试验的最低要求。常规脱水装置是指材料为15.56℃～48.89℃(60℉～120℉),操作压力大于或等于2.76MPa (表压）（400psig)，但不超过ANSI B16.5 6001b 法兰设计压力下操作的脱水装置。 本标准脱水装置主要包括进料分离器、甘醇/天然气吸收塔、天然气/甘醇换热器、甘醇重沸器、甘醇缓冲罐、甘醇循环泵、过滤器、贫富甘醇换热器、甘醇闪蒸分离器（可选）以及撬座。本标准也可用于海上平台脱水装置的设计，但应满足海上平台装置的附加要求。 成套脱水装置的制造商应负责保证所有材料、设计、制造程序，检验、验收以及试验均满足本标准的要求。

Specification for glycol-type gas dehydration units

DIN EN ISO 10434:2005 石油、石油化学和相关工业用螺栓帽状钢闸阀

Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004); German version EN ISO 10434:2004

ARMY A-A-52302 VALID NOTICE 1-2004 内陆石油分配系统插接耦合垫片和分裂积分

A-A-52302, dated 6 April 1992, has been reviewed and determined to be valid for use in acquisition

GASKET, SPLIT INTEGRAL, FOR INLAND PETROLEUM DISTRIBUTION SYSTEM (IPDS) SNAP-JOINT COUPLING

ISO 13704:2001/Cor 1:2004 石油和天然气工业.石油炼油厂内加热器管厚度的计算.技术勘误1

Petroleum and natural gas industries - Calculation of heater-tube thickness in petroleum refineries; Technical Corrigendum 1

ISO 10438-2:2003 石油、化工和天然气工业.润滑、油封、控油系统和辅助装置.第2部分:专用油系统

This part of ISO 10438 specifies requirements for oil systems supplying oil to compressors requiring seal oil, and to other machines, in special-purpose applications for use in the petroleum, petrochemical and natural gas industries as well as in other industries by agreement. It is intended to be used in conjunction with ISO 10438-1. ISO 10438 in its entirety specifies requirements for lubrication systems, oil-type shaft-sealing systems, self-acting gas seal systems, control-oil systems and other auxiliaries for general- or special-purpose applications. These systems can serve equipment such as compressors, gears, pumps and drivers. None of the parts of ISO 10438 is applicable to internal combustion engines.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems

ISO 10438-1:2003 石油、化工和天然气工业.润滑、油封、控油系统和辅助装置.第1部分:一般要求

This part of ISO 10438 specifies general requirements for lubrication, shaft-sealing systems and control-oil systems and auxiliaries for use in the petroleum, petrochemical and natural gas industries as well as in other industries by agreement. It is intended to be used in conjunction with ISO 10438-2, ISO 10438-3 and ISO 10438-4, as appropriate. ISO 10438 in its entirety specifies requirements for lubrication systems, oil-type shaft-sealing systems, self-acting gas seal systems, control-oil systems and other auxiliaries for general- and special-purpose applications. These systems can serve equipment such as compressions, gears, pumps and drivers. None of the parts of ISO 10438 is applicable to internal combustion engines.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements

ISO 10438-3:2003 石油、化工和天然气工业.润滑、油封、控油系统和辅助装置.第3部分:通用油系统

This part of ISO 10438 specifies requirements for oil systems supplying lubricating oil to machines in general-purpose applications for use in the petroleum, petrochemical and natural gas industries as well as in other industries by agreement. It is intended to be used in conjunction with ISO 10438-1. ISO 10438 in its entirety specifies requirements for lubrication systems, oil-type shaft-sealing systems, self-acting gas seal systems, control-oil systems and other auxiliaries for general- or special-purpose applications. These systems can serve equipment such as compressors, gears, pumps and drivers. General-purpose applications are limited to lubrication systems. None of the parts of ISO 10438 is applicable to internal combustion engines. Typical schemas for general-purpose oil systems are provided in Annex A. NOTE General-purpose systems supply lubricating oil only (i.e. no seal oil) and do not require an accumulator to cover transient conditions.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems

ISO 10438-4:2003 石油、化工和天然气工业.润滑、油封、控油系统和辅助装置.第4部分:自动气封支撑系统

This part of ISO 10438 specifies requirements for support systems for self-acting gas seals (dry gas seals) as described in ISO 10439, for use in the petroleum, petrochemical and natural gas industries as well as in other industries by agreement. It is intended to be used in conjunction with ISO 10438-1. ISO 10438 in its entirety specifies requirements for lubrication systems, oil-type shaft-sealing systems, self-acting gas seal systems, control-oil systems and other auxiliaries for general- or special-purpose applications. These systems can serve equipment such as compressors, gears, pumps and drivers. None of the parts of ISO 10438 is applicable to internal combustion engines. NOTE Annex A provides schemas of typical dry-gas seal support systems.

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems

SANS 50858-2:2003 轻液体(例如：油和石油)分离器系统．标称尺寸、安装、运行和维护的选择

Applies to separator systems used to separate hydrocarbons of mineral origin from wastewater. Does not apply to grease and oils of vegetable or animal origin nor to separation of emulsions or solutions. Provides guidance on the selection of nominal sizes

Separator systems for light liquids (e.g. oil and petrol) Part 2: Selection of nominal size, installation, operation and maintenance

BS EN 858-2:2003 轻液体(例如:油和石油)分离器系统.标称尺寸、安装、运行和维护的选择

This European Standard applies to separator systems used to separate hydrocarbons of mineral origin from wastewater. It does not apply to grease and oils of vegetable or animal origin nor to separation of emulsions or solutions. This European Standard provides guidance on the selection of nominal sizes, as well as the installation operation and maintenance of light liquid separators manufactured in accordance with EN 858-1. It also gives advice on the suitability of cleansing agents if they are discharged to a separator.

Separator systems for light liquids (e.g. oil and petrol) - Selection of nominal size, installation, operation and maintenance

DIN EN ISO 8222:2003 石油测量系统.校准.容积验证箱校准温度修正

This Standard specifies multiplication factors for the correction of the volume of water transferred from a primary measure to a tank for changes arising from temperature differences during the determination of the capacity of the tank at reference temperature.

Petroleum measurement systems - Calibration - Temperature corrections for use when calibrating volumetric proving tanks (ISO 8222:2002); German version EN ISO 8222:2002

SANS 50858-1:2002 轻液体(例如:油和石油)分离器系统．第1部分：产品设计原则，性能和测试，标识和质量控制

Specifies definitions, nominal sizes, principles of design, performance requirements, marking, testing and quality control for separator systems for light liquids. Applies to separator systems for light liquids, where light liquids are separated from was

Separator systems for light liquids (e.g. oil and petrol) Part 1: Principles of product design, performance and testing, marking and quality control

SY/T 6536-2002 钢质水罐内壁阴极保护技术规范

1.0.1 为了规范钢质水罐内壁阴极保护系统的设计、施工、管理、运行，特制定本规范。 1.0.2 本规范适用于新建和已建钢质水罐内壁的强制电流阴极保护系统和牺牲阳极阴极保护系统。 1.0.3 阴极保护技术既可以单独用来控制浸水表面的腐蚀，也可以与覆盖层或其它保护方法配合使用。阴极保护技术不能保护非浸水表面。 1.0.4 钢质水罐内壁阴极保护系统的设计、施工、管理、运行，除应符合本规范外，尚应符合国家现行的有关强制性标准、规范的规定。

Specification of cathodic protection of internal submerged surfaces of steel water storage tanks

BS EN 858-1:2002 轻液体(例如:油和石油)分离器系统.产品设计、性能和测试、标记和质量控制的原则

This standard specifies definitions, nominal sizes, principles of design, performance requirements, marking, testing and quality control for separator systems for light liquids. This standard applies to separator systems for light liquids, where light liquids are separated from waste water by means of gravity and/or coalescence. This standard does not apply to the treatment of stable emulsions, solutions of light liquids and water, grease and oils of vegetable and animal origin.

Separator systems for light liquids (e.g. oil and petrol) - Principles of product design, performance and testing, marking and quality control

ISO 13705:2001 石油和天然气工业 一般炼油厂用燃烧加热器

This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and burners for general refinery service.

Petroleum and natural gas industries - Fired heaters for general refinery service

ISO 13704:2001 石油和天然气工业 石油炼油厂内加热管管粗的计算

This International Standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes for petroleum refinery heaters. These procedures are appropriate for designing tubes for service in both corrosive and non-corrosive applications. These procedures have been developed specifically for the design of refinery and related process fired heater tubes (direct-fired, heat-absorbing tubes within enclosures). These procedures are not intended to be used for the design of external piping. This International Standard does not give recommendations for tube retirement thickness; annex A describes a technique for estimating the life remaining for a heater tube.

Petroleum and natural gas industries - Calculation of heater-tube thickness in petroleum refineries

SY/T 5262-2000 火筒式加热炉规范

本规范规定了火筒式加热炉设计、制造、检验与验收的基本要求。 本规范适用于陆上油、气田生产中使用的火筒式加热炉的设计、制造、检验与验收。

Specification for fire tube type heater

SY/T 0321-2000 钢质管道水泥砂浆衬里技术标准

本标准适用于油田外径不小于60.3mm的钢质输水管道衬里的设计、施工及验收。所输送水的pH值不得低于5，且温度不宜高于60℃。

Technical standard of cement mortar lining of steel pipeline