E97 油、气处理设备 标准查询与下载

SY 0027-1994 稠油集输及注蒸汽系统设计规范

本规范油气集输部分适用于下列条件之一的油田: 用注蒸汽方法开采的油田。 用常规方法开采的抽田， 其原油温度在50℃ 时，动力粘度大于0.4Pa.s, 温度在20℃ 时， 密度大于0.9161g/cm3。 本规范的注蒸汽系统部分适用于: 饱和蒸汽温度小于或等于360℃，饱和蒸汽压力小于或等于18.6MPa。

Code for Design of Heavy Oil Gathering and Steam Injection System

ASTM F1372-93(2005) 气体分配系统组件用金属表面状态的扫描式电子显微镜(SEM)分析的标准试验方法

The purpose of this test method is to define a procedure for testing components being considered for installation into a high-purity gas distribution system. Application of this test method is expected to yield comparable data among components tested for purposes of qualification for this installation. 1.1 This test method covers the testing of interior surfaces of components such as tubing, fittings, and valves for surface morphology. 1.2 This test method applies to all surfaces of tubing, connectors, regulators, valves, and any metal component, regardless of size. 1.3 Limitations: 1.3.1 This methodology assumes a SEM operator skill level typically achieved over a 12-month period. 1.3.2 This test method shall be limited to the assessment of pits, stringer, tears, grooves, scratches, inclusions, stepped grain boundaries, and other surface anomalies. However, stains and particles that may be produced during specimen preparation should be excluded in the assessment of anomalies. 1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 6.

Standard Test Method for Scanning Electron Microscope (SEM) Analysis of Metallic Surface Condition for Gas Distribution System Components

ARMY A-A-52302-1992 内陆石油分配系统插接耦合垫片和分裂积分

The split integral gasket shall be compatible for use with diesel fuels and jet fuels.

GASKET, SPLIT INTEGRAL, FOR INLAND PETROLEUM DISTRIBUTION SYSTEM (IPDS) SNAP-JOINT COUPLING

SY/T 0540-1994 石油工业加热炉型式与基本参数

Types and basic parameters of heating furnaces in petroleum industry

SY/T 0538-1994 管式加热炉技术条件

Technical conditions of tubular heating furnace

ASTM D4174-89(2010) 石油液压装置的清理,冲洗及净化标准操作规程

Proper fluid condition is essential for the satisfactory performance and long life of the equipment. Prerequisites for proper lubrication and component performance are: (1) a well-designed hydraulic system, (2) the use of a good fluid, and (3) a maintenance program including proper filtration methods to ensure that the fluid is free of contaminants. These prerequisites are meaningless unless the hydraulic system is initially cleaned to a level that will prevent component damage on initial start up or when debris may be dislodged by any system upset. The cleaning and flushing of both new and used systems are accomplished by essentially the same procedure. In new systems, the emphasis is on the removal of contaminants introduced during the manufacture, storage, field fabrication, and installation. In used systems, the emphasis is on the removal of contaminants that are generated during operations, from failures that occur during operation; or contaminants introduced during overhaul. While the flushing and cleaning philosophies stated in this practice are applicable to all primary and servo hydraulic systems, the equipment specified herein does not apply to compact systems that use relatively small volumes of fluid unless they are servo systems where it is economically justified. It should be emphasized that the established procedures to be followed for flushing and cleaning the hydraulic systems should be accomplished through the cooperative efforts and agreement of the equipment manufacturer, the installer, the operator, and the fluid supplier. No phase of these procedures should be undertaken without a thorough understanding of the possible effects of improper system preparation. The installation and cleaning and flushing of the equipment should not be entrusted to persons lacking in experience. 1.1 This practice covers aid for the equipment manufacturer, the installer, the oil supplier and the operator in coordinating their efforts towards obtaining and maintaining clean petroleum fluid hydraulic systems. Of necessity, this practice is generalized due to variations in the type of equipment, builder's practices, and operating conditions. Constant vigilance is required throughout all phases of design, fabrication, installation, flushing, testing, and operation of hydraulic systems to minimize and reduce the presence of contaminants and to obtain optimum system reliability.

Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems

ASTM D4174-89(2005) 石油液压系统的清理、冲洗及净化的标准实施规程

Proper fluid condition is essential for the satisfactory performance and long life of the equipment. Prerequisites for proper lubrication and component performance are: (1) a well-designed hydraulic system, (2) the use of a good fluid, and (3) a maintenance program including proper filtration methods to ensure that the fluid is free of contaminants. These prerequisites are meaningless unless the hydraulic system is initially cleaned to a level that will prevent component damage on initial start up or when debris may be dislodged by any system upset. The cleaning and flushing of both new and used systems are accomplished by essentially the same procedure. In new systems, the emphasis is on the removal of contaminants introduced during the manufacture, storage, field fabrication, and installation. In used systems, the emphasis is on the removal of contaminants that are generated during operations, from failures that occur during operation; or contaminants introduced during overhaul. While the flushing and cleaning philosophies stated in this practice are applicable to all primary and servo hydraulic systems, the equipment specified herein does not apply to compact systems that use relatively small volumes of fluid unless they are servo systems where it is economically justified. It should be emphasized that the established procedures to be followed for flushing and cleaning the hydraulic systems should be accomplished through the cooperative efforts and agreement of the equipment manufacturer, the installer, the operator, and the fluid supplier. No phase of these procedures should be undertaken without a thorough understanding of the possible effects of improper system preparation. The installation and cleaning and flushing of the equipment should not be entrusted to persons lacking in experience. 1.1 This practice covers aid for the equipment manufacturer, the installer, the oil supplier and the operator in coordinating their efforts towards obtaining and maintaining clean petroleum fluid hydraulic systems. Of necessity, this practice is generalized due to variations in the type of equipment, builder's practices, and operating conditions. Constant vigilance is required throughout all phases of design, fabrication, installation, flushing, testing, and operation of hydraulic systems to minimize and reduce the presence of contaminants and to obtain optimum system reliability.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems

GOST 5.1730-1972 轻石油产品过滤用的ФГН-60M型过滤器.检定产品的质量要求

Настоящий стандарт распространяется на фильтры ФГН-60М, предназначенные для очистки светлых нефтепродуктов от механических примесей

The filters of delicate purity of light oil production. Quality requirements for certified products

BS 1676:1970 焦油和沥青用加热器(移动式和可搬运的)规范

Metric units.

Specification for heaters for tar and bitumen (mobile and transportable)

SHJ 1037-1984 炼油厂管式加热炉钢结构工程及配件安装工程技术条件

Refinery tubular heating furnace steel structure engineering and fittings installation engineering technical conditions

HBm 98-1992 油田气轻烃回收装置铝制板翅式换热器通用技术条件

本标准规定了铝制板翅式换热器的技术要求、试验方法、检验规则及包装、运输和贮存要求。 　　本标准适用于用盐浴钎焊法制造的油田气轻烃回收和其它石油化工装装置用铝制板翅式换热器（以下简称换热器）。用其它钎焊法制造的换热器，可参照执行。

General technical specifications for aluminum plate-fin heat exchangers of oilfield gas light hydrocarbon recovery unit

HBm 96-1992 油田气轻烃回收装置术语

本标准规定了油田气轻烃回收装置及其主要部件在设计、制造和使用中常用的术语。 　　本标准适用于油田气轻烃回收装置及主要部件专业人员在研制、设计、制造、装调，使用维护诸环节中，对制定标准、编写技术文件、交流技术编译专业文献等方面起到概念明确和词义统一的使用

Terminology of oilfield gas light hydrocarbon recovery unit

SHJ 1039-1984 炼油厂管式加热炉炉管胀接工程技术条件

Refinery tubular heating furnace tube expansion engineering technical conditions

HBm 97-1992 油田气轻烃回收装置通用技术条件

本标准规定了低、中压油田气轻烃回收装置（以下简称装置）的基本技术要求、试验方法和检验规则等。装置一般包括气源、压缩、冷却、分离、干燥、制冷、换热、分馏、贮运、测量控制、公用工程及工艺管道等部分 　　本标准适用于采用膨胀机制冷，从油田气或凝析气中回收天然气凝液（ＮＧＬ）或液化石油气（ＬＰＧ）和稳定轻烃的装置。也适用于对天然气进行低温分离脱水的装置。采用其它方法制冷来回收轻烃的装置亦可参照执行。

General Technical Specifications for Oilfield Gas and Light Hydrocarbon Recovery Units