G30 合成材料综合 标准查询与下载

KS M ISO 1923:2010 泡沫塑料和橡胶.线性尺寸的测定

이 표준은 발포 재료의 시험편 또는 시트, 블록의 길이 측정을 위한 측정 도구와 절차의 특

Cellular plastics and rubbers-Determination of linear dimensions

KS M ISO 1409:2009 塑料/橡胶.聚合物的含水分散体和橡胶胶乳(天然的和合成的).用环形试验法测定表面张力

이 표준은 고분자 분산과 고무 라텍스(천연과 합성)의 표면 장력 측정을 위한 고리 방법을

Plastics/rubber－Polymer dispersions and rubber latices (natural and synthetic)－Determination of surface tension by the ring method

KS M ISO 1432:2009 硫化橡胶或热塑橡胶.低温硬化查曼(GEHMAN)试验.测定

게만 시험으로 알려진 것으로, 이 표준은 실온에서 약 -150 ℃까지의 온도 범위에서 가황

Rubber, vulcanized or thermoplastic-Determination of low temperature stiffening(Gehman test)

DIN EN ISO 845:2009 蜂窝结构塑料和橡胶.表观密度的测定(ISO 845:2006),德文版本EN ISO 845:2009

This International Standard specifies a method for determining the apparent overall density and the apparent core density of cellular plastics and rubbers. If the material to be tested includes skins formed during a moulding/extrusion, the apparent overall density or the apparent core density, or both, can be determined. If the material does not have skins formed during moulding, the term "overall density" is not applicable For shaped materials, a different method such as buoyancy method may be used.

Cellular plastics and rubbers - Determination of apparent density (ISO 845:2006); English version of DIN EN ISO 845:2009-10

KS M ISO 4646:2009 橡胶或塑料涂覆织物.低温冲击试验

이 표준은 고무 또는 플라스틱으로 코팅된 천에 규정된 충격을 가했을 때 코팅 부분에 금이

Rubber- or plastics-coated fabrics-Low-temperature impact test

KS M ISO 2411:2009 橡胶或塑料涂层织物.涂层粘合力的测定

이 표준은 고무 또는 플라스틱으로 코팅된 천의 접착 강도 시험방법에 대하여 규정한다.

Rubber- or plastics-coated fabrics－Determination of coating adhesion

KS M ISO 5978:2009 橡胶或塑料涂覆织物.耐粘结性测定

이 표준은 고무 또는 플라스틱으로 코팅된 천의 블로킹 시험방법에 대하여 규정한다.

Rubber- or plastics-coated fabrics－Determination of blocking resistance

KS M ISO 5979:2009 橡胶或塑料涂层织物.柔性的测定.扁环法

이 표준은 고무 또는 플라스틱으로 코팅된 천의 유연성 시험방법 중 플랫 루프법에 대하여 규

Rubber or plastics coated fabrics－Determination of flexibility－Flat loop method

DIN EN ISO 8067:2009 柔性蜂窝聚合材料.撕裂强度的测定(ISO 8067:2008),DIN EN ISO 8067:2009-06的英文版本

This International Standard specifies two methods for the determination of the tear strength of flexible cellular polymeric materials: -- method A, using a trouser test piece; -- method B, using an angle test piece without a nick.

Flexible cellular polymeric materials - Determination of tear strength (ISO 8067:2008); English version of DIN EN ISO 8067:2009-06

ASTM D5672-09 使用25 mm(1 in)挠曲技术试验压痕力挠曲的软微孔材料测量的标准试验方法

The 25-mm (1-in.) deflection IFD method is recommended for production screening and quality control on full size cushions only. Applicable cushion thicknesses to be tested by this test method are only those listed in this test method. Further research and development are required before this test method will be applicable to other cushion thicknesses. This test method is designed to give a value approximating the 25 % IFD on a 100-mm (4-in.) thick piece of foam when the actual specimen thickness tested is within the ranges listed in the test method. In case of disagreement, the referee method is the IFD procedure in Test Methods D 3574, Test B1. The user of this test method shall establish the correlation between this test method and the referee method.1.1 This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness. 1.2 This test method is limited to foams with thicknesses that are 75 mm (3 in.) or greater. 1.3 This test method is based on the fact that the traditional industry standard thickness for Indentation Force Deflection (IFD) is 100 mm (4 in.), and the traditional percent deflection for IFD acceptance and product planning is 25 %. With respect then to these traditional industry conventions, a 25 % deflection on a 100-mm (4-in.) cushion would be 25 mm (1 in.). Thus, deflecting proper thickness cushions 25 mm (1 in.) will determine if the flexible polyurethane foam is within the specified grade range for 25 % IFD. 1.4 Cushion thicknesses less than 75 mm (3 in.) shall not be tested for IFD using this test method. 1.5 This test method is intended to provide a quick and simple method to screen flexible polyurethane foams for determination of its firmness grade. 1.6 The values stated in SI units are to be regarded as standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;This test method and ISO 2439 address the same subject matter, but differ in technical content.

Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm (1-in.) Deflection Technique

ANSI/CSA LC7-2009 管接头密封化合物和材料

Pipe Joint Sealing Compounds and Materials

ASTM D3171-09 复合材料成分含量用标准试验方法

A constituent content of a composite material must be known in order to analytically model the material properties (mechanical, physical, thermal, or electrical) of the composite which are affected by the reinforcement or matrix. Also, knowledge of the constituent content is required for evaluation of the quality of a fabricated material and the processes used during fabrication. The void volume of a composite material may significantly affect some of its mechanical properties. Higher void volumes usually mean lower fatigue resistance, greater susceptibility to moisture penetration and weathering, and increased variation or scatter in strength properties. Knowledge of the void volume of a composite material is desirable as an indication of the quality of a composite. Reinforcement content may be used to normalize mechanical properties affected by amount of reinforcement in the coupon.1.1 These test methods determine the constituent content of composite materials by one of two approaches. Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content (by weight or volume), and the cured ply thickness, based on the measured thickness of the laminate. Method II is not applicable to the measurement of void volume. 1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case. 1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal matrices. The suggested applications are discussed in Section 4, as well as at the start of each procedure. 1.1.3 Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium. A procedure for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace. 1.1.4 Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an acceptable tolerance. The presence of voids is not measured. Eq 9 and 10 assume zero void content to perform the calculation. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional information.

Standard Test Methods for Constituent Content of Composite Materials

KS M ISO 4651:2008 泡沫橡胶和塑料.动态弹性的测定

이 표준은 시험편 위에 추를 떨어뜨렸을 때 추의 최대 감속도를 측정함으로써 발포 고무 재료

Cellular rubbers and plastics－Determination of dynamic cushioning performance

KS M ISO 4638:2008 泡沫柔性聚合材料.气流透过率的测定

이 표준은 공기 흐름에 대한 연질 발포 고분자의 투과성 측정 방법에 대하여 규정한다.

Polymeric materials, cellular flexible－Determination of air flow permeability

DIN EN ISO 3385:2008 软质泡沫聚合材料.使用恒负荷冲击进行疲劳测定

This International Standard specifies a method for the deter- mination of loss in thickness and loss in hardness of flexible cellular materials intended for use in upholstery. This test method provides a means of assessing the service per- formance of flexible cellular materials of the latex and polyether urethane types used in load-bearing upholstery. The measured loss in thickness and loss in hardness are related to, but are not necessarily the same as, the losses likely to oc- cur in service. The method is applicable both to standard size test pieces cut from stock material and to shaped components.

Flexible cellular polymeric materials - Determination of fatigue by constant load pounding (ISO 3385:1989); German version EN ISO 3385:1995

NF T42-009:2008 橡胶和塑料.聚合物分散体和橡胶胶乳.pH值的测定

Rubber and plastics - Polymer dispersions and rubber latices - Determination of pH.

UL 1694 BULLETIN-2008 小型聚合物制部件材料易燃性试验UL安全性标准

The following (Proposal dated June 10, 2005) are subject to comment: (1) Updating reference to Needle Flame Test based on issuance of IEC 60695-11-5. (2) Clarification of total flame time for application of flame/burner if flame is inadvertently extinguished

UL Standard for Safety Tests for Flammability of Small Polymeric Component Materials

KS M ISO 3386-2:2008 泡沫柔性聚合材料.压缩应力应变特性的测定.第2部分:高密度材料

이 표준은 250 kg/m3을 초과하는 고밀도 연질 발포 고분자 재료의 압축 응력-변형 특

Flexible cellular polymeric materials-Determination of stress-strain characteristics in compression-Part 2:High-density materials

KS M ISO 3386-1:2008 泡沫柔性聚合材料.压缩应力应变特性的测定.第1部分:低密度材料

이 표준은 250 kg/m3 이하의 저밀도 연질 발포 고분자 재료의 압축 응력-변형 특성을

Polymeric materials, cellular flexible-Determination of stress-strain characteristic in compression-Part 1:Low-density materials

UL 546 BULLETIN-2008 导线端接符合材料调查大纲

OUTLINE OF INVESTIGATION FOR CONDUCTOR TERMINATION COMPOUNDS

OUTLINE OF INVESTIGATION FOR CONDUCTOR TERMINATION COMPOUNDS