合成橡胶标准-分析测试百科网

BS ISO 27588:2012 硫化或热塑橡胶.用非常低橡胶硬度(VLRH)等级测定静负荷硬度

Rubber, vulcanized or thermoplastic. Determination of dead-load hardness using the very low rubber hardness (VLRH) scale

ICS: 83.060
CCS: G35
发布: 2012-08-31
实施: 2012-08-31

NF S94-064-2:2012 外科植入物. 陶瓷材料. 第2部分: 带氧化锆增强的高纯度氧化铝基复合材料.

Implants for surgery - Ceramic materials - Part 2 : composite materials based on a high-purity alumina matrix with zirconia reinforcement.

ICS: 11.040.40
CCS: G35
发布: 2012-07-01
实施: 2012-07-13

NF T45-003:2012 橡胶合成配料.硫.试验方法

Rubber compounding ingredients - Sulfur - Methods of test.

ICS: 83.040.20
CCS: G35
发布: 2012-02-01
实施: 2012-02-25

ISO 14932:2012 橡胶配合剂.有机硫化剂.有机过氧化物含量的测定

Rubber compounding ingredients - Organic vulcanizing agents - Determination of organic peroxide content

ICS: 83.040.20
CCS: G35
发布: 2012-01
实施

SH/T 1610-2011 热塑性弹性体.苯乙烯-丁二烯嵌段共聚物(SBS)

本标准规定了热塑性弹性体苯乙烯-丁二烯嵌段共聚物（SBS）(以下简称SBS)的要求、试验方法、检验规则以及包装、标志、贮存、运输等。本标准适用于以苯乙烯和1，3-丁二烯为主要原料，采用阴离子聚合方法制得的线型SBS、星型SBS及添加填充油的SBS，该SBS主要用于改性沥青、制鞋和制胶黏剂。

Thermoplastic elastomers.Styrene-butadiene block copolymer

ICS: 83.040.10
CCS: G35
发布: 2011-12-20
实施: 2012-07-01

SH/T 1743-2011 乙烯-丙烯-二烯烃橡胶（EPDM）.评价方法

警告：使用本标准的人员应熟悉正规实验室操作规程。本标准无意涉及因使用本标准可能出现的所有安全问题。制定相应的安全和健康规程并确保符合国家法规是使用者的责任。范围：本标准规定了： ——生胶的物理和化学试验； ——评价乙烯-丙烯-二烯烃橡胶（即三元乙丙橡胶）及其充油橡胶的硫化特性所用的标准材料、标准试验配方、设备和操作程序。

Rubber,ethylene-propylene-diene(EPDM).Evaluation procedure

ICS: 83.060
CCS: G35
发布: 2011-12-20
实施: 2012-07-01

This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. The purpose of this document is to provide guidance to the engineer in the selection of practical, commercially available rubber materials, and further to provide a method for specifying these materials by the use of a simple line call-out designation. This document was developed to permit the addition of descriptive values for future rubber materials without complete reorganization of the classification system and to facilitate the incorporation of future new methods of test to keep pace with changing industry requirements.

Classification System for Rubber Materials