G43 橡胶密封件 标准查询与下载

SAE AMS7284/1-1990 耐航空燃料的65-75 Shore A 磷氮基氟橡胶(FZ)密封环

This specification covers a phosphonitrilic fluoroelastomer (FZ) in the form of molded rings. Primarily for use in aircraft fuels systems operating from -55 to +150 degrees C (-67 to 302 degrees F).

Rings, Sealing, Phosphonitrilic Fluoroelastomer (FZ) Aviation Fuel Resistant 65 - 75 Shore A

SAE AMS7266B-1990 一般用途的耐高温、燃料及油的65-75氟代硅酮橡胶密封环

This specification covers a fluorosilicone rubber in the form of molded rings. Primarily for use in applications requiring resistance to jet fuel and lubricating oil. The elevated test temperatures were selected as the maximum temperatures at which reproducible laboratory data could be obtained. These temperatures do not necessarily indicate, nor are they to be construed as, the maximum operating temperatures at which these rings can be used.

Rings, Sealing, Fluorocarbon Rubber General Purpose, High Temperature, Fuel and Oil Resistant 65 - 75

SAE AMS7258B-1990 耐燃料低收缩65-75的丁腈橡胶密封环

This specification covers butadiene acrylonitrile (NBR) rubber in the form of molded rings. Primarily for use in aircraft fuel systems operating from -55 degrees to +125 degrees C (-67 degrees +257 degrees F). These rings contain less plasticizer than normally used in aircraft fuel seals; therefore, there is less shrinkage when the rings are dried out.

Rings, Sealing, Butadiene-Acrylonitrile (NBR) Rubber Fuel Resistant, Low Shrinkage 65 - 75

SAE AMS7284/2-1990 耐航空燃料的75-85 Shore A 磷氮基氟橡胶(FZ)密封环

This specification covers phosphonitrilic fluoroelastomer (FZ) in the form of molded rings. Primarily for use in aircraft fuel systems operating from -55 to +150 degrees C (-67 to +302 degrees F).

Rings, Sealing, Phosphonitrilic Fluoroelastomer (FZ) Aviation Fuel-Resistant 75 - 85 Shore A

ARMY MIL-R-47211 A-1989 室温固化硅胶

This specification covers general purpose, room temperature curing, silicone rubber compunds(see 6.1).

RUBBER, SILICONE, ROOM TEMPERATURE CURING

HG/T 3097-1989(1997) 110℃以下热水输送管橡胶密封圈材料规范

本标准规定110℃以下热水输送管用橡胶密封圈材料的要求。 本标准适用于输送110℃以下热水用的包括铸铁、钢等管道的橡胶密封圈。 本标准不包括用泡沫橡胶材料或其他闭孔结构材料制成的密封圈。 若对密封圈有特殊性能要求，则由供需双方商定。

Rubber scals-joint rings for water supply pipelines up to 110℃-Specification for materials

SAE AMS7265B-1988 耐磷酸酯流体乙烯丙烯橡胶密封环75 85

This specification covers Rings, Sealing, Ethylene Propylene (EPM) Rubber, Phosphate Ester Hydraulic Fluid Resistant, 75 85

Rings, Sealing, Ethylene Propylene (EPM) Rubber, Phosphate Ester Hydraulic Fluid Resistant, 75 85

HG/T 3094-1988(1997) 液压气动用多层唇形密封组件 测量叠层高度的方法

Fluid power systems and componentsMultiple lip packing tsets Methods for measuring stack heights

HG/T 3093-1988(1997) 石油基油类输送管道及连接件用橡胶密封制品胶料

Rubber seals material for petroleum product supply pipes and fittings

HG/T 3092-1988(1997) 燃气输送管及配件用橡胶密封圈胶料

Material of rubber seals used for gas supply pipes and fittings

HG/T 3094-1988 液压气动用多层唇形密封组件.测量叠层高度的方法

Fluid power systems and components-Multiple lip packing sets-Methods for measuring stack heights

HG/T 3092-1988 燃气输送管及配件用橡胶密封圈胶料

Material of rubber seals used for gas supply pipes and fittings

HG/T 3093-1988 石油基油类输送管道及连接件用橡胶密封制品胶料

Rubber seals material for petroleum product supply pipes and fittings

SAE AMS7262B-1988 耐磷酸盐酯液流的乙烯丙烯橡胶密封环85 95

This specification covers Rings, Sealing, Ethylene Propylene (EPM) Rubber, Phosphate Ester Hydraulic Fluid Resistant, 85 95

Rings, Sealing, Ethylene Propylene (EPM) Rubber, Phosphate Ester Hydraulic Fluid Resistant, 85 95

SAE AMS7264A-1988 耐高温65-75低压缩硅酮橡胶密封环

This specification covers a silicone rubber in the form of molded rings. Sealing rings for use from -55 +205 °C (-65 +400 °F) in dynamic applications and from -60 to +260 °C (-80 to +500 °F) in static applications.

RINGS, SEALING, SILICONE RUBBER High Temperature Resistant, Low Compression Set 65 - 75

ISO 3601-3:1987 流体系统 密封装置 O形圈 第3部分:质量验收准则

Fluid systems; Sealing devices; O-rings; Part 3 : Quality acceptance criteria

ASTM F147-87(2017) 非金属衬垫材料柔韧性的标准试验方法

4.1 This test method is designed to measure the ability of non-metallic gasket materials to withstand handling, as would be encountered before and during installation of cut gaskets. 1.1 This test method covers the determination of the flexibility of non-metallic gasket materials. It is designed for testing specimens cut from sheet goods or from the gasket in the finished form, as supplied for commercial use. Materials normally classified as rubber compounds are excluded since they are covered in Classification D2000. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flexibility of Non-Metallic Gasket Materials

ASTM F147-87(2009) 非金属衬垫材料挠性的标准试验方法

This test method is designed to measure the ability of non-metallic gasket materials to withstand handling, as would be encountered before and during installation of cut gaskets.1.1 This test method covers the determination of the flexibility of non-metallic gasket materials. It is designed for testing specimens cut from sheet goods or from the gasket in the finished form, as supplied for commercial use. Materials normally classified as rubber compounds are excluded since they are covered in Classification D2000. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flexibility of Non-Metallic Gasket Materials

HG/T 2947-1986 铝背水壶橡胶密垫封片

Rubber gasket for aluminium canteen

NAVY MIL-S-3105 C VALID NOTICE 1-1986 用于军火的惰性封口剂

Specification MIL-S-3105C, dated 4 December 1970; has been reviewed and - determined to be current.

SEALING COMPOUND, INERT (FOR USE IN AMMUNITION)