G43 橡胶密封件 标准查询与下载
共找到 402 条与 橡胶密封件 相关的标准，共 27 页
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
Dimensional tolerance of O-ring rubber seal
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
本标准规定了O形橡胶密封圈（简称O形圈）的密封结构形式、沟槽尺寸、公差与表面粗糙度等。 本标准适用于HB 7509～7519规定的O形圈。
O-ring rubber seal groove
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
本标准规定了Ｏ形橡胶密封圈（简称Ｏ形圈）验收要求。 本标准适用于ＨＢ ７５０９～７５１９规定的Ｏ形圈。其它Ｏ形圈可参照使用。
O-ring rubber seal acceptance specification
- ICS
- CCS
- G43
- 发布
- 1997-09-23
- 实施
- 1997-10-01
This notice should be filed in front of MIL-R-472 1 1A(MI), dated O 1 Aug 1990.
RUBBER, SILICONE, ROOM TEMPERATURE CURING
- ICS
- 49.025.40
- CCS
- G43
- 发布
- 1997-04-28
- 实施
本标准规定了汽车液压制动橡胶皮碗的分类、要求、抽样、试验方法及标志、包装、运输和贮存。 本标准适用于汽车液压制动缸(包括主缸和轮缸)用的橡胶皮碗。
Hydraulic brake rubber cups for automobiles
- ICS
- 83.140.50
- CCS
- G43
- 发布
- 1997-04-21
- 实施
- 1997-10-01
1.1 This specification covers the material requirements for preformed elastomeric strip seals and the corresponding steel locking edge rail used in expansion joint sealing. The scope of this specification is limited to preformed non-reinforced strip seals that mechanically lock into structural steel locking lugs. The sealing element can consist of a single layer strip or have multiple webs depending on individual project requirements. The structural steel locking edge rail shall be anchored into the structure in accordance with the purchaser's specific details. While the scope of this specification is limited to the materials used in fabrication of strip sealing systems, it is recommended that a practical means of testing the watertightness aspects of the individual systems either in the field or at a testing laboratory be developed. When used on highway bridges, limits on maximum joint opening and minimum steel thicknesses need to be addressed. 1.2 The values stated in the inch-pound system shall be considered as standard.
Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing
- ICS
- 83.140.50
- CCS
- G43
- 发布
- 1997
- 实施
1.1 This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
- ICS
- 23.040.80 (Seals for pipe and hose assemblies)
- CCS
- G43
- 发布
- 1997
- 实施
Asbestos-rubber sheet gaskets for pipe flanges
- ICS
- CCS
- G43
- 发布
- 1996-12
- 实施
- 1997-07-01
