G52 涂料辅助材料 标准查询与下载

EN ISO 16773-1:2016 电化学阻抗谱(EIS)涂层和无涂层金属试件第1部分:术语和定义(ISO 16773-1:2016)

Dieser Teil von ISO 16773 legt Begriffe für die elektrochemische Impedanzspektroskopie (EIS) fest, die für die weiteren Teile von ISO 16773 gelten.

Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 1: Terms and definitions

EN ISO 14647:2016 金属涂层-金属基体上金覆盖层孔隙率的测定硝酸蒸汽试验(ISO 14647:2000)

Diese Internationale Norm legt die Prüfeinrichtung und ein Verfahren zur Bestimmung der Porosität mittels Salpetersäuredampf in Goldüberzügen, insbesondere galvanische Abscheidungen und Plattierungen, für elektrische Kontakte fest. Dieses Verfahren beabsichtigt aufzuzeigen, ob die Porosität geringer oder größer als ein Wert ist, der vom Anwender als erfahrungsgemäß zulässig für den vorgesehenen Verwendungszweck gilt. Sie ist geeignet für Inlays oder Plattierungen, die mindestens 75 % Gold enthalten, für galvanische Überzüge, die mehr als 95 % Gold enthalten, oder für Grundwerkstoffe aus Kupfer, Nickel und deren Legierungen, die gewöhnlich für elektrische Kontakte verwendet werden. Die Prüfung mit Salpetersäuredampf ist für Goldüberzüge mit einer geringeren Dicke als 0,6 µm zu streng. Außerdem ist diese Prüfung ungeeignet für metallische Überzüge, die weniger edel als Gold oder Platin sind, z. B. Palladium und dessen Legierungen oder teilvergoldetes Palladium und dessen Legierungen. In ISO 10308 und in der Literatur sind mehrere andere Porositätsprüfverfahren beschrieben.

Metallic coatings - Determination of porosity in gold coatings on metal substrates - Nitric acid vapour test

DIN EN ISO 8623:2015 色漆和清漆用松焦油脂肪酸.测试方法和特征值(ISO 8623-2015);德文版本EN ISO 8623-2015

Tall-oil fatty acids for paints and varnishes - Test methods and characteristic values (ISO 8623:2015); German version EN ISO 8623:2015

BS EN ISO 8623:2015 涂料和清漆用松焦油脂肪酸.试验方法和特征值

Tall-oil fatty acids for paints and varnishes. Test methods and characteristic values

KS M ISO 15013:2011 塑料.挤压聚丙烯.要求事项与试验方法

Plastics--Extruded sheets of polypropylene(PP)--Requirements and test methods

KS M ISO 19334:2013 涂料和清漆用粘合剂.松香.气相色谱分析

이 표준은 검 로진에 포함된 일정 로진산의 양을 측정하기 위한 가스 크로마토그래피 방법에 대하여규정하며, 이와 같은 산의 휘발성 메틸에스터 분석에 맞는 모세관 가스 크로마토그래피를 사용한다.이 방법은 특정한 소나무 종에 존재하는 검 로진을 확인하기 위한 목적으로 주로 이용되지만, 검 로진을 정량적으로 분석하는 용도로 이용되지는 않는다. 이러한 분석이 필요한 경우, ASTM D 5974에명시된 내부 표준 방법을 이용해야 한다.

Binders for paints and varnishes — Gum rosin — Gas chromatographic analysis

ISO 16482-2:2013 涂料和清漆粘合剂.水性松香树脂分散体的非挥发性物质含量的测定.第2部分:微波法

This part of ISO 16482 specifies a method for determining the non-volatile content, by mass, of aqueous rosin-resin dispersions, using a microwave oven. This method is applicable to resin dispersions having a softening point from 60 °C to 100 °C, measured in accordance with ISO 4625-1 (ring-and-ball method).

Binders for paints and varnishes - Determination of the non-volatile-matter content of aqueous rosin-resin dispersions - Part 2: Microwave method

ISO 16482-1:2013 涂料和清漆粘合剂.水性松香树脂分散体的非挥发性物质含量的测定.第1部分:烘箱法

This part of ISO 16482 specifies a method for determining the non-volatile content, by mass, of aqueous rosin-resin dispersions, using an oven. This method is applicable to resin dispersions having a softening point from 60 °C to 100 °C, measured in accordance with ISO 4625-1 (ring-and-ball method).

Binders for paints and varnishes - Determination of the non-volatile-matter content of aqueous rosin-resin dispersions - Part 1: Oven method

KS M ISO 10283:2012 漆和其他涂层材料用粘结剂.异氰酸酯树脂中单体二异氰酸酯的测定

이 표준은 톨루엔 디이소시아네이트1 ), 헥사메틸렌 디이소시아네이트, 이소포론 디이소시아네

Binders for paints and varnishes－ Determination of monomeric diisocyanates in isocyanate resins

BS EN ISO 13632:2012 涂料和清漆用粘合剂.树脂.色泽检验的取样和试样制备

Binders for paints and varnishes. Rosin. Sampling and sample preparation for colour measurement

ISO 13632:2012 涂料和清漆用粘合剂.树脂.色泽检验的取样和试样制备

This International Standard specifies a procedure for sampling of rosin and rosin derivatives from — drums, — the molten/liquid form, — flakes, pellets or pastilles and preparation of the samples for colour measurement. The method to be used for the colour measurement is specified in other standards. The colour of the rosin can be measured with neat rosin or rosin in solution. The two most commonly used colour-measurement methods are those based on the USDA1) scale and the Gardner colour scale. Annex A provides information on the correlation between these two scales.

Binders for paints and varnishes - Rosin - Sampling and sample preparation for colour measurement

ASTM D890-12 液体松脂中水含量的标准试验方法

1.1 These test methods cover the quantitative determination of dissolved or occluded water present in any proportion in liquid pine chemicals, such as turpentine, pinene, dipentene, pine oil, tall oil, and tall oil fatty acids. Three methods of moisture testing are included. The Karl Fisher titration method is the preferred method for testing tall oil, Test Methods D803. 1.1.1 The Karl Fischer Titration method is based on the reaction between water and a complex reagent2 consisting of iodine, sulfur dioxide, pyridine, and methanol, whereby the iodine is converted to a colorless compound. The appearance of a persistent iodine color in the reaction mixture indicates the complete removal of free water by reaction with the reagent, and the endpoint may be measured colorimetrically. Automatic titrators find this endpoint by the restoration of a current strength when the resistance provided by the presence of water is eliminated. Amperometric automatic titrators find this endpoint by detecting the current flow that occurs once water is eliminated. 1.1.2 The coulometric titration method determines water content by electronic integration of a current sufficient to generate the precise amount of iodine from the required reagent to react with the water in the sample. 1.1.3 The azeotropic method utilizes the relatively low boiling point of water, as compared with other sample constituents, in a toluene or xylene matrix so that water is collected in a trap and measured. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water in Liquid Pine Chemicals

ASTM D803-12 妥尔油测试的标准试验方法

1.1 Tall oil is used primarily as a commercial source of fatty acids and rosin, and, therefore, reliable methods for the analysis of these components is necessary. 1.1 These test methods cover the test procedures to be applied to whole tall oils or refined tall oils. Previous editions of these test methods have described test procedures that are used to test tall oil fatty acid, rosin, and other tall oil-derived products as well as test crude and refined tall oil. Consequently, these test methods are widely cited in reference books and industry literature for the testing of tall oil-derived products. 1.1.1 In this current revision, procedural details of some of the often-cited test methods have been removed and the test methods consolidated with other existing test methods. In such cases the consolidated methods, applicable to all tall oil-derived products. 1.2 The procedures appear in the following order: Physical Tests Sections Viscosity: 8199;Brookfield Method (Preferred Method) 7 8199;Bubble Time Method 8 Flash Point 9 Color 10 Moisture: 11

Standard Test Methods for Testing Tall Oil

ASTM D233-12 松脂的取样和测试的标准试验方法

1.1 These test methods cover procedures for sampling and testing turpentine, as defined by the Code of Federal Regulations and Terminology D804. These test methods are also used for the sampling and testing of pinenes, the major components of most turpentines. 1.2 These test methods primarily measure the physical rather than the chemical properties of turpentines and pinenes. As turpentines and pinenes are currently used chiefly as chemical raw materials for the production of resins and synthetic organic chemicals, chemical composition is also very important. Consequently, testing the chemical composition of turpentines and pinenes by gas chromatography has displaced these test methods to a large extent. (See for example Test Methods D6387.) 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Sampling and Testing Turpentine

KS M ISO 150:2011 涂料和清漆用生的、精制的和熟的亚麻仁油.规范和试验方法

이 표준은 도료와 바니시용 천연 아마인유, 정제 아마인유, 아마 보일유의 품질 규격과 시험

Raw, refined and boiled linseed oil for paints and varnishes－Specifications and methods of test

UL 2767-2011 油漆和清漆去除剂

Paint and varnish remover

DIN EN ISO 19334:2011 涂料和清漆用粘合剂.松香.气相色谱分析(ISO 19334-2010).德文版本EN ISO 19334-2011

This Standard specifies a gas-chromatographic method for determining the amounts of certain rosin acids in gum rosin using capillary gas-chromatographic separation of the volatile methyl esters of these acids. It intended primarily to permit the identification of gum rosin from specific species of pine trees. It is not designed for the quantitative analysis of gum rosin. If such analyses are required, the internal-standardtechnique specified in ASTM D 5974 should be used.

Binders for paints and varnishes - Gum rosin - Gas-chromatographic analysis (ISO 19334:2010); German version EN ISO 19334:2011

DIN EN ISO 276:2011 涂料和清漆用粘合剂.亚麻子油.要求和试验方法(ISO 276-2002);德文版本EN ISO 276-2010

Binders for paints and varnishes - Linseed stand oil - Requirements and methods of test (ISO 276:2002); German version EN ISO 276:2010

DIN EN ISO 14446:2011 色漆和清漆用粘合剂.工业乙酸纤维素溶液粘度测定及此类溶液的分类 (ISO 14446-1999);德文版本EN ISO 14446-2010

Binders for paints and varnishes - Determination of the viscosity of industrial cellulose nitrate solutions and classification of such solutions (ISO 14446:1999); German version EN ISO 14446:2010

DIN EN ISO 4619:2011 涂料和清漆用干燥剂(ISO 4619-1998);德文版本EN ISO 4619-2010

This International Standard specifies the requirements and the corresponding test methods for driers for paints, varnishes and related products. The requirements relate to driers in the solid or liquid form.

Driers for paints and varnishes (ISO 4619:1998); German version EN ISO 4619:2010