G52 涂料辅助材料 标准查询与下载

ASTM D3970-05(2011) 氧化滴定法测定涂料干燥剂中铈的标准试验方法

This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry.1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate. 1.2 This test method is not applicable to dryer blends. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7.

Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

ASTM D2373-05 用EDTA法测定涂料干燥剂中钴的标准试验方法

The amount of cobalt drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated cobalt content of a pure liquid cobalt drier soluble in glacial acetic acid and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of cobalt in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).1.2 This test method is not applicable to drier blends. If driers other than cobalt are present, they may interfere by reacting with EDTA under the conditions used for analysis.1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Cobalt in Paint Driers by EDTA Method

ASTM D2375-05 用EDTA法测定涂料干燥剂中锰的标准试验方法

The amount of manganese drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated manganese content of pure liquid manganese drier soluble in toluene-alcohol and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of manganese in liquid paint driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).1.2 This test method is not applicable to drier blends.1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Manganese in Paint Driers by EDTA Method

ASTM D3734-05 高闪点芳烃石脑油的标准规范

1.1 This specification covers two types of aromatic hydrocarbon solvents, normally petroleum distillates, having high flash points, moderately low volatility, and a distillation range of approximately 30C (50F). These solvents are used primarily by the coatings industry and are commonly referred to as high-flash aromatic naphthas.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for High-Flash Aromatic Naphthas

ASTM D3926-05 二氧化钛浆料中固体百分比的标准试验方法

These test methods are intended as a quick and reliable procedure for measuring the titanium dioxide pigment content of aqueous slurries. Included with the pigment content in the percent solids are the various nonvolatile additives used in preparing a stable slurry. Because the aluminum and silica oxide treatments on the more highly treated titanium dioxide pigments may change somewhat with prolonged drying, in the oven method the solids of the slurry are considered dry after heating at 105°C for 60 to 65 min. The high temperature associated with the infrared moisture analyzer may also effect a change in the aluminum and silica oxide treatment on highly treated TiO2 products. Therefore, care in selection of time and temperature are critical to obtain accurate results with the infrared method. With the short duration of test associated with the microwave drying system, overdrying is not a concern.1.1 These test methods cover the determination of the weight percent of solids in aqueous slurries of titanium dioxide pigments by either the use of a gravity-convection oven (Method A), infrared radiation moisture analyzer (Method B), or a microwave drying system (Method C).1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This test standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Percent Solids in Titanium Dioxide Slurries

ASTM D608-05(2011) 邻苯二甲酸二丁酯的标准规格

1.1 This specification covers dibutyl phthalate (99 % grade). 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for Dibutyl Phthalate

ASTM D3970-05 氧化滴定法测定涂料干燥剂中铈的标准试验方法

This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry.1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate.1.2 This test method is not applicable to dryer blends.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section .

Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

NF T30-045-2*NF EN ISO 6744-2:2004 色漆和清漆用粘合剂.醇酸树脂.第2部分:邻苯二甲酸酐含量的测定

Binders for paints and varnishes - Alkyd resins - Part 2 : determination of phthalic anhydride content.

DIN EN ISO 15880:2004 色漆、清漆和粘合剂.水基涂料和粘合剂的MEQ值的测定

The standard specifies a titrimetric method for determining the MEQ (milli-equivalent) value of water-based binders and coating materials, either as MEQ(acid) value or an MEQ(alkali) value.#,,#

Paints, varnishes and binders - Determination of MEQ value of water-based coating materials and binders (ISO 15880:2000); German version EN ISO 15880:2004

DIN 51405:2004 色漆和清漆用石油烃类、类似的液体和溶剂.气体色谱法分析.一般的工作原理

This standard establishes the basis for the gaschromatographic analysis of petroleum products, both for the quantitative determination of single substances and for their quantitative presence in a sample. The standard is also applicable to related products e.g. solvents in paint. The standard provides a general description of a gas chromatograph, describes the analysis and the interpretation of results. It also explains and defines basic parameters such as gaschromatography, gaschromatogram, zero-line, base-line, peak, peak height, peak width at half heigh, peak area, separation number, peak asymmetrie, retention time, relative retention and retention index.#,,#

Testing of mineral oil hydrocarbons, similar liquids and solvents for paints and varnishes - Analysis by gas chromatography - General working principles

DIN 55652:2003 涂料和清漆溶剂.痕量酸度测定

The standard describes a test method for determining the acidity, expressed as the acid content (as a mass fraction of acetic acid in percent)or as the acid value, of solvents and material mixtures. The methods are applicable to alcohols, ketones, ethers, esters, aliphatic and aromatic hydrocarbons and mixtures prepared from these chemicals having an lower acid content up to 0,1%, resp. an acid value less than 0,001 mg KOH/g.#,,#

Solvents for paints and varnishes - Determination of acidity of traces

ASTM D1720-03(2012) 硝酸纤维素溶液中活性溶剂稀释比的标准试验方法

1.1 This test method covers the determination of the volume ratio of hydrocarbon diluent to active solvent required to cause persistent heterogeneity (precipitation) in a solution of cellulose nitrate. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6. 1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Test Method for Dilution Ratio of Active Solvents in Cellulose Nitrate Solutions

ASTM D964-03(2008)e1 防污涂料用金属铜粉的标准规范

1.1 This specification covers copper powder for use in antifouling paints. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Metallic Copper Powder for Use in Antifouling Paints

ASTM D1720-03(2008) 硝酸纤维素溶液中活性溶剂稀释比的标准试验方法

By use of standard or reference grade materials for any two of the three components, namely, oxygenated solvent, diluent, or cellulose nitrate, the effect of different batches or different types of the third component can be determined. This test method is applicable for the determination of the following: The dilution ratio of toluene as the standard diluent to an oxygenated solvent under test, using as the solute standard cellulose nitrate as defined in 5.2. The dilution ratio of a hydrocarbon diluent under test to n-butyl acetate as the standard solvent, using as a solute standard cellulose nitrate as defined in 5.2. The dilution ratio of toluene, as the standard diluent, to n-butyl acetate as the standard solvent, using as the solute cellulose nitrate of varying solubility characteristics. The information developed through this test may be useful in the formulation of cellulose-based lacquers and adhesives.1.1 This test method covers the determination of the volume ratio of hydrocarbon diluent to active solvent required to cause persistent heterogeneity (precipitation) in a solution of cellulose nitrate. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6. 1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Test Method for Dilution Ratio of Active Solvents in Cellulose Nitrate Solutions

KS M ISO 3262-12:2002 涂料用填充剂.规范和试验方法.第12部分:白云母类云母

이 규격은 백운모형 운모에 대한 품질과 시험 방법에 대하여 규정한다.

Extenders for paints－Specifications and methods of test－Part 12：Muscovite－type mica

KS M ISO 3262-11:2002 涂料用填充剂.规范和试验方法.第11部分:含碳酸盐的片状天然滑石

이 규격은 탄산염을 포함하는 층상형의 천연 활석으로 만들어진 제품에 대한 품질과 시험 방법

Extenders for paints－Specifications and methods of test－Part 11：Natural talc, in lamellar form, containing carbonates

KS M ISO 3262-16:2002 涂料用填充剂.规范和试验方法.第16部分:氢氧化铝

이 규격은 수산화 알루미늄의 품질 규격과 그에 따른 시험 방법에 대하여 규정한다.

Extenders for paints－Specifications and methods of test－Part 16 : Aluminium hydroxides

DIN 53177:2002 涂料和清漆用粘合剂.液态树脂动态粘度的测量.根据乌贝罗德(Ubbelohde)法采用等温型毛细管粘度计测量树脂溶剂和油

Binders for paints and varnishes - Measurement of the dynamic viscosity of liquid resins; Resin solutions and oils by the capillary viscosimeter of isocelses type according to Ubbelohde

DIN 53176:2002 涂料和清漆用粘合剂.水可稀释的粘合剂胺含量的测定

Binders for paints and varnishes - Determination of the amine value of water thinnable binders

BS EN ISO 277:2010 涂料和清漆用粘合剂.生桐油.试验方法和要求

Binders for paints and varnishes. Raw tung oil. Requirements and methods of test