G80 感光材料基础标准与通用方法 标准查询与下载

HG/T 4399-2012 胶印印刷版材用成膜酚醛树脂

本标准规定了胶印印刷版材用成膜酚醛树脂的要求、试验方法、检验规则和标志、包装、运输及贮存。本标准适用于以烷基酚和甲醛合成的热塑性胶印印刷版材用成膜酚醛树脂。

Novolak resins used for offset plates

HG/T 4396-2012 印刷电路板用重氮盐胶片

本标准规定了印刷电路板用重氮盐胶片的要求、试验方法、检验规则、包装及标志、贮存和运输。本标准适用于在聚酯片基上涂布含重氮盐的感光涂层而制成的印刷电路板重氮盐胶片。

Diazo film for printed circuit board (PCB)

HG/T 4397-2012 胶印版材用重氮萘醌感光剂

本标准规定了胶印版材用重氮萘醌感光剂的术语和定义、要求、试验方法、检验规则和标志、包装、运输及贮存。本标准适用于以线型酚醛树脂或多酚化合物与重氮萘醌磺酰氯为原料,经酯化而成的胶印版材用重氮萘醌感光剂。

Photo sensitizers of naphthoquinonediazido used for offset plates

HG/T 4293-2012 彩色电影正片感光度和格码测定方法

本标准规定了彩色电影正片的感光度和格码的求取方法以及试验条件。 本标准适用于彩色电影正片的感光度及格码的测定，此类胶片用于通过底片印刷正片制作成彩色电影发行拷贝。本标准同时也适用于制作幻灯片的彩色正片材料的感光度及格码测定。

Determination of color motion picture positive film sensitivity speed and gamma

HG/T 4127-2010 医用干式胶片

本标准规定了医用干式胶片的要求、试验方法、检验规则及包装、标志、运输和贮存。 本标准适用于医用干式胶片。

Medical dry imaging film

HG/T 4128-2010 喷墨打印用透明胶片

本标准规定了喷墨打印用透明胶片的要求、检验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于用作水基墨水喷墨打印的透明胶片。

Clear film for inkjet printing

HG/T 4129-2010 照相级喷墨打印墨水

本标准规定了照相级的喷墨打印水基墨水的产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于用作照相级的喷墨打印用水基墨水。

Photographic grade inkjet printing ink

HG/T 4130-2010 喷墨打印用金银箔胶片

本标准规定了喷墨打印用金银箔胶片的要求、试验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于用作水基墨水喷墨打印的金银箔胶片。

Gold and silver foil film for inkjet printing

HG/T 4149-2010 印刷版材用化学品.2-重氮-1-萘醌-5-磺酰氯

本标准规定了印刷版材用化学品 2-重氮-1-萘醌-5-磺酰氯的要求、试验方法、检验规则、包装及标志、贮存和运输。 本标准适用于印刷版材使用的原材料2-重氮-1-萘醌-5-磺酰氯，不适用于电子行业使用的215。 分子式：CHClNOS 结构式：略 相对分子质量：268.67（按2007年国际相对原子质量）

Chemicals applied in Printing Plates.2-Diazo-1- Naphthoquinone -5-Sulfonyl Chloride

HG/T 2913-2008 艺术摄影散页胶片尺寸

本标准规定了艺术摄影使用的黑白和彩色（负-正或反转加工法）散页胶片的尺寸、垂直度、直线度、感光面的要求、检验方法和包装标志。 本标准适用于业余、广告和肖像艺术摄影，不包括特殊用途的胶片，如文件复制、照相排版和印刷制版摄影用胶片。

Photography.Film dimensions.Pictorial sheets

HG/T 4003-2008 黑白涂塑散页相纸尺寸

本标准规定了黑白涂塑散页相纸的裁切尺寸、垂直度、直线度的检验方法和包装标志。 本标准适用于印相或放大用的黑白涂塑散页相纸。

Black and White RC paper dimensions-sheets

HG/T 3938-2007 彩色喷墨打印用聚氯乙烯(PVC)证卡材料

本标准规定了彩色喷墨打印用证卡材料的技术要求、试验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于以聚氯乙烯（PVC）为支持体的有背胶和无背胶的彩色喷墨打印用证卡材料。

PVC card materials for colour inkjet printing

ASTM E1735-07 测定曝光于4到25MeV的X射线下工业射线照片底片的相对影象质量用标准试验方法

This test method provides a test for determining the relative image quality response of radiographic film when exposed to 4 to 25 MeV X rays as any single component of the total X-ray system (for example, screens) is varied. By holding the technique parameters (except exposure time) and processing parameters constant, the image quality response of radiographic film may be evaluated on a relative basis. Alternately, this test method provides a test for measuring the image quality of the X-ray system or any component of the system. 1.1 This test method covers determination of the relative image quality response of industrial radiographic film when exposed to X-radiation sources having photon energies from 4 to 25 MeV. Evaluation of the film is based on the visibility of holes in a special image quality indicator (IQI). Since results for a given film type may vary, depending on the particular processing system and processing conditions used, it is essential to state the exposure parameters and achieved density, processing chemistry, processing cycle, and processing temperature. For the purposes of this test method, it is assumed that all components of the X-ray system are operating properly and are capable of producing a given image quality. This test method is not intended to be used for films exposed with Cobalt 60 sources or X-ray sources below 4 MeV.1.2 The values stated in either SI or inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Relative Image Quality of Industrial Radiographic Film Exposed to X-Radiation from 4 to 25 MeV

ANSI/I3A IT2.45-2006 摄影.医用单色透视图像的观察条件的表征方法

Provides methods for determining luminance and luminance spatial uniformity of illuminators used for viewing medical films that have viewing areas of 18 cm x 24 cm or larger. It also provides a method for measuring the illuminance falling on the medical film from light sources other than the illuminator.

Photography - Viewing Conditions for Transilluminated Monochrome Medical Images - Method for Characterizing

HG/T 3557-2001 感光材料均一性的测定

本标准规定了银盐感光材料均一性的测定方法。 本标准主要适用于银盐系统的黑白和彩色电影胶片，其他白炽钨光和模拟日光曝光的银盐感光材料也可适用。 本标准不适用于采用非钨灯类特殊光源(如激光、荧光)曝光的感光材料。

Determination of the uniformity of photographic materials

HG/T 3569-2001 成色剂光吸收的测定

本标准规定了成色剂光吸收的测定方法。 本标准适用于外观为白色的油溶性成色剂。

Determination of light absorption for couplers

ISO/TR 18931:2001 成像材料 湿度测量和控制建议

This Technical Report discusses devices in photographic standardization that are used as hygrometers and humidistats in the measurement and control of relative humidity (RH) in test chambers and storage areas. Special attention is given to situations where a photographic standard specifies controlling relative humidity to ±2 % RH or better. Electric hygrometers are recommended for their precision, low cost, and accuracy when properly calibrated. Calibration can be done either by the vendor or in-house by a dew-point measurement. Where the budget permits, dew-point combined with ambient temperature measurements (converted to relative humidity) may be the only sensor system.

Imaging materials - Recommendations for humidity measurement and control

ISO/TR 18930:2001 成像材料 户外气候实验协议

This Technical Report discusses a recommended way to prepare and submit specimens for outdoor weathering testing in a variety of locations and covers issues of durability to weather, temperature and environmental influences. This Technical Report describes the pertinent information to request from the testing service, how to instruct the testing service in the appropriate placement of the test specimens, and lists the type of information to report upon completion of a weathering test. This Technical Report does not discuss what to measure or how to make the measurement as these are best left to the discretion of the experimenter.

Imaging materials - Protocols for outdoor weathering experiments

JIS K 7616:2001 摄影.处理后的摄影材料中残留硫代硫酸盐和其他相关化学品的测定.碘-直链淀粉法、亚甲兰法及硫化银法

この規格は，現像処理済み写真感光材料中の残留チオ硫酸塩などのよう素，アミロース法，メチレンブルー法及び硫化銀法による試験方法について規定する。この規格は，ハロゲン化銀，ゼラチン写真感光材料に現像，定着及び最終水洗を行って得た写真に通用する。 ただし，黒白安定化処理方式，熱現像方式及びィンスタント写真方式の写真には適用しない。

Photography -- Determination of residual thiosulfate and other related chemicals in processed photographic materials -- Methods using iodine-amylose, methylene blue and silver sulfide

HG/T 3680-2000 彩色胶卷和相纸照片.冲洗加工技术规范

本标准规定了彩色冲洗扩印店冲洗彩色胶卷和扩印彩色照片的技术要求、 试验方法、检验规则。 本标准适用于使用C-41系列及兼容工艺类型的彩色负片自动冲洗机和EP-2、RA-4系列及兼容工艺类型的彩色相纸自动扩印机的彩色冲印店。

Specification for processing.Photographic colour films and paper prints