共找到 250 条与 金属理化性能试验方法综合 相关的标准,共 17 页
GB/T12967 的本部分规定了着色阳极氧化膜经紫外光照射后颜色变化的对比方法。 本部分适用于不具有热敏感性的着色阳极氧化膜。 注:在本部分规定的试验条件下〉深色试样表向通常会达到较高的温度“2 方法原理。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 4:Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings
本部分规定了通过变形检验阳极氧化膜抗破裂性能的方法。本部分适用于铝及铝合金板状材料薄阳极氧化膜(阳极氧化膜厚度小于5 μm)抗破裂性的测定。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 5:Assessment of resistance of anodic oxidation coatings to cracking by deformation
本部分规定了采用落砂试验仪测定阳极氧化膜耐磨性的方法。 本部分适用于铝及铝合金阳极氧化膜耐磨性的测定。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 7: Measurement of abrasion resistance of anodic oxidation coatings by sand falling test apparatus
本标准规定了镁合金铸件X射线实时成像无损检测方法。但未规定铸件内部不均匀性的可接受准则。 本标准适用于对镁合金铸件内部不均匀性的种类和严重程度进行实时无损检测。
X-ray real-time radioscopic testing method for magnesium alloy castings
GB/T 22638的本部分规定了用针孔箱检测铝箔针孔的方法。 本部分适用于铝箔针孔数量及针孔直径的检测。
Test methods for aluminium and aluminium alloy foils.Part 2:Determination of porosity
GB/T 22638的本部分规定了重量法测定铝箔厚度的方法。 本部分适用于厚度不大于0.05mm的铝箔的厚度测定。
Test methods for aluminium and aluminium alloy foils.Part1:Determination of thickness by gravimetric method
GB/T 22638的本部分规定了铝箔的粘附性测定方法。 本部分适用于检测铝箔层与层间的粘附程度。
Test methods for aluminium and aluminium alloy foils.Part3:Determination of stickiness
GB/T 22638的本部分规定了空调器散热片用涂层铝箔亲水性的测定方法。 本部分适用于空调散热片用涂层铝箔亲水性的测定。
Test methods for aluminium and aluminium alloy foils.Part9:Determination of hydrophilic property
GB/T 22638的本部分规定了空调器散热片用涂层铝箔的表面密度测定方法。 本部分适用于空调器散热片用涂层铝箔表面密度的测定。
Test methods for aluminium and aluminium alloy foils.Part 10:Determination of mass per unit area (surface density) of coatings
GB/T 22638的本部分规定了铝箔的刷水试验方法。 本部分适用于铝箔表面脱脂状况的检查。
Test methods for aluminium and aluminium alloy foils.Part5:Determination of wettability by brushing
GB/T 22638的本部分规定了药品包装用铝箔的热风强度的测定方法。 本部分适用于铝箔与要用聚氯乙烯(PVC)、聚偏二氯乙烯(PVDC)等硬片粘合后制成的固体药品(片剂、胶囊剂等)包装用铝箔粘合层的热封强度的测定。
Test methods for aluminium and aluminium alloy foils.Part7:Determination of heat seal strength
GB/T 22638的本部分规定了铝箔表面润湿张力的测定方法。 本部分适用于铝箔表面润湿张力的测定。
Test methods for aluminium and aluminium alloy foils.Part4:Determination of surface wetting tension
GB/T 22638的本部分规定了铝箔的直流电阻测定方法。 本部分适用于电力、无线电电容器用铝箔20℃时标准试样的直流电阻测定。
Test methods for aluminium and aluminium alloy foils.Part6:Determination of direct current resistance
本标准规定了利用涡流测试铝合金电导率的方法。 本标准规定的方法适用于铝合金材料或产品。 本标准规定的电导率涡流测试方法与其他试验方法结合,可间接鉴别材料或产品的热处理状态和性能(如组织均匀性、力学性能、时效状态、过烧程度和抗应力腐蚀性能等)。
The method for determining aluminum alloys conductivity using eddy current
本部分规定了铝及铝合金着色阳极氧化膜色差和外观质量的检测方法。 本部分适用于铝及铝合金着色阳极氧化膜产品色差和外观质量的检测。
Test Methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 6: Determination of color differences and appearance of colored anodic oxide films by viewing method
本部分规定了一个用轮式磨损试验仪测定铝及铝合金阳极氧化膜的耐磨性及磨损系数的试验方法。 本部分适用于阳极氧化膜的厚度不小于5μm的板片状铝试样检验。对于阳极氧化膜的整个层厚以及表层或任意选定的氧化膜的某一层都可以用本方法测定其耐磨性和磨损系数。 本部分不适用于试样表面凹凸不平的阳极氧化试样的测定。 有机聚合物膜耐磨性的测定可参照本部分。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 2:Measurement of wear resistance and wear index of anodic oxidation coatings with an abrasive wheel wear test apparatus
本部分规定了铝及铝合金阳极氧化膜的铜加速乙酸盐雾试验方法。 本部分也规定了评价盐雾试验箱环境腐蚀性的方法。 本部分适用于评定阳极氧化膜的抗盐雾腐蚀能力,也适用于同一种阳极氧化膜的工艺质量比较。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 3:Copper accelerated acetic acid salt spray test(CASS test)
本部分规定了使用喷磨试验仪测定铝及铝合金阳极氧化膜的平均耐磨性并与标准试样、协议参化试样的耐磨性进行比较的试验方法。 本部分适用于膜厚不小于5μm的铝及铝合金阳极氧化膜的检验,尤其适用于检验区直径约为2mm的小试样和表面不平的试样。 使用设计合理的喷磨试验仪、涡流测厚仪和万用表,可以进行分层检验,反映耐磨性沿膜厚方向变化的情况(参见附录B)。 由于不同批次的磨料会使试验结果产生一定的误差,所以本试验只是一种相对的检验。
Test methods for anodic oxidation coatings of aluminium and aluminium alloys.Part 1:Measurement of meat specific abrasion resistance of anodic oxidation coatings with an abrasive jet test apparatus
本标准规定了预应力混凝土用钢材的拉伸、弯曲、反复弯曲、扭转、缠绕、等温松弛、疲劳、应力腐蚀、偏斜拉伸、化学分析、几何尺寸测量和相对肋面积确定等试验方法。 本标准适用于预应力钢丝、钢棒、钢绞线等产品相关性能的测定
Steel for prestressed concrete.Test methods
本标准规定了一种测定金属薄板和薄带塑性应变比的方法 。
Determination of Plastic Strain Ratio (r-value) of Sheets and Strips of Metallic Materials
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号