H43 钢锭、钢坯 标准查询与下载

KS D ISO 19960:2006 特殊物理性能的铸钢及合金

이 규격은 특수한 물성을 가진 주강과 합금의 종류를 규정한다. 이 규격에서 다루어지는 주강

Cast steels and alloys with special physical properties

YB/T 5351-2006 高温合金锻制圆饼

High temperature alloy forged round cake

YB/T 5125-2006 含钒生铁

含 負 生 鐵 本标准规定了含钒生铁的技术要求 ，试验方法、檢驗規則和质量证明书。 本标准适用于炼钢或铸造用的含钒生铁，也适用于提炼钒用的含钒生铁。

Vanadium pig iron

YB/T 4149-2006 连铸圆管坯

本标准规定了连铸圆管坯的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本标准适用于制造无缝钢管的连铸圆管坯。

Continuously cast round billet for seamless steel tube rolling

ASTM A892-06 规定高碳轴承钢微观结构的定义和等级

1.1 This guide covers the description of carbide structures in annealed high carbon bearing steels.1.2 Included is a guide for rating steel specimens by a graded series of photomicrographs showing the incidence of certain conditions. 1.3 The reference photomicrographs are graded illustrations of annealed carbides categorized by size, network, and lamellar content (shape). 1.4 This guide is to facilitate communication and description of microstructure. It does not establish limits of acceptability. Such limits are a matter of agreement between user and producer.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels

ASTM A1040-06 规范锻造碳钢、低合金钢、合金钢统一的标准等级组分的标准指南

1.1 This guide covers ASTM Subcommittees A01.02, A01.03, A01.06, A01.09, A01.11, A01.15, A01.19, A01.22, and A01.28 for specifying chemical composition limits of wrought carbon, low-alloy, and alloy steels. It is intended that these recommended grade composition limits be suitable for adoption by other standardization bodies that prepare standards for carbon, low-alloy, and alloy steel products, including discontinued steels.1.2 Included in this guide are the recommendations for determining the number of significant figures for specifying chemical composition.1.3 The carbon and alloy steel grades in all standards overseen by the aforementioned ASTM subcommittees have been included, except those grades applicable to restricted special end uses.1.4 Not addressed are minor composition modifications that a specific ASTM subcommittee may find necessary to accommodate effects of normal processing or to enhance fabricability by the producer or user, or both.1.5 Also not generally addressed (except where established by ASTM subcommittees) is a complete rationalization of all limits, especially where such would conflict with long-standing practices and is not justified by special technical effect.1.6 This guide does not address discontinued or formerly standard steel grades. A listing of such steel grades can be found in SAE J1249. Also excluded from this guide are cast materials and welding filler metals.

Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

YB/T 5058-2005 弹簧钢、工具钢冷轧钢带

本标准规定了弹簧钢和工具钢冷轧钢带的分类和代号、尺寸、外形、重量、技术要求、试验和检验、包装、标志及质量证明书等。 本标准适用于制造弹簧、刀具、带尺等制品、轧制宽度小于600mm的弹簧钢和工具钢冷轧钢带。

Cold-rolled spring and tool steel strips

YB/T 037-2005 优质结构钢冷拉扁钢

本标准规定了冷拉扁钢的订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本标准适用于矩形截面优质碳素结构钢和合金结构钢的冷拉扁钢(以下简称扁钢)。

Quality structure cold-draw flat steels

YB/T 5059-2005 低碳钢冷轧钢带

本标准规定了低碳钢冷轧钢带的分类和代号、尺寸、外形、重量、技术要求、试验和检验、包装、标志及质量证明书等。 本标准适用于制造受冲击压零件、钢管和其他金属制品，轧制宽度小于600mm的低碳钢冷轧钢带。

Cold-rolled low carbon steel strips

ISO 19960:2005 特殊物理性能的铸钢及合金

This International Standard specifies cast steel and alloy grades with special physical properties. The cast steel and alloy grades covered by this International Standard are used in applications which require low linear thermal expansion, or low ferromagnetic responses, or low galling properties.

Cast steels and alloys with special physical properties

ARMY MIL-S-47319 A VALID NOTICE 2-2005 高强度热处理铸坯和锻造的钢棒

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

STEEL, BAR, BILLET AND FORGINGS COBALT-FREE MARAGING

KS D ISO 9477:2004 一般工程和结构用高强度铸钢

1.1 이 규격은 일반 공업용 및 구조용 목적을 위한 4종의 열처리 주강과 주강 합금강

High strength cast steels for general engineering and structural purposes

YB/T 2012-2004 连续铸钢板坯

本标准规定了非合金钢、低合金钢和合金钢连续铸钢板坏的尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、运输、贮存、标志和质量证明书。 　　本标准适用于按GB/T 13304-1991中第二部分分类的非合金钢、低合金钢和合金钢连续铸钢板坏。

continuous cast steel slab

YB/T 2011-2004 连续铸钢方坯和矩形坯

本标准规定了非合金钢、低合金钢和合金钢连续铸钢方坯和矩形坯的定义、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、运输、贮存、标志和质量证明书。 　　本标准适用于按GB/T 13304-1991中第二部分分类的非合金钢、低合金钢和合金钢连续铸钢方坯和矩形坯。

Continuous casting of billets and rectangular billets

YB/T 5222-2004 优质碳素结构钢圆管坯

本标准规定了优质碳素结构钢圆管坯的订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则和包装、标志、质量证明书等。 　　本标准适用于制造无缝钢管用直径50~450mm的优质碳素结构钢连铸和热轧圆管坯。

Quality carbon structural steel round tube blank

AWWA C561-2004 制造不锈钢滑门

This standard describes fabricated stainless steel slide gates with full aperture closure, designed for either seating or unseating head, or both, in ordinary water supply service.

Fabricated Stainless Steel Slide Gates

ASTM A711-04 钢锻件坯料标准规范

1.1 This specification covers cast carbon and alloy steel ingots and strand castings, semi-wrought ingots and strand castings and rolled or forged blooms, billets, and slabs for forging. 1.2 Blooms, billets, and slabs are semi-finished steel products, hot rolled or forged to approximate cross-sectional dimensions. Blooms and billets may be square, round, octagonal, or rectangular in section; slabs are rectangular. Although no invariable rule prevails between the terms blooms and billets, and they are frequently used interchangeably, the following size distinctions are in general use. 1.2.1 Blooms8212;Cross-sectional area greater than 36 in.2 (232 cm2). 1.2.2 Billets8212;Maximum cross-sectional area 36 in.2 (232 cm2. 1.2.3 Slab8212;Minimum thickness, 11/2 in. (38.0 mm); width, more than twice the thickness; and generally a cross-sectional area of not less than 16 in. 2 (103 cm2). 1.2.4 Ingots either top or bottom poured or secondary remelted are covered. 1.2.5 Strand castings with or without additional reduction are covered. 1.3 Supplementary requirements (S1 to S19) of an optional nature are provided. They shall apply only when specified by the purchaser. 1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.1.5 Unless the order specifies the "M" specification, the material shall be furnished to the inch-pound units.

Standard Specification for Steel Forging Stock

ASTM A345-04 磁设备用平轧电炉钢的标准规范

1.1 This specification covers general procedures for specifying requirements in the procurement and delivery of flat-rolled electrical steels for magnetic applications. When an applicable individual specification does not exist, this specification enables the user to order a suitable material to be supplied under controlled conditions with respect to magnetic quality, sampling, testing, packaging, and so forth, by specifying certain requirements on the purchase order and citing this specification.1.2 Individual specifications that are in conformity with this specification are Specifications A 677/A 677M, A 683/A 683M, A 726, A 840, and A 876.Note 1For more information on procedures associated with this specification, refer to the following: Test Methods A 341/A 341M, A 343/A 343M, A 348/A 348M, A 596/A 596M, A 712, A 719/A 719M, A 720/A 720M, A 721/A 721M, A 773/A 773M, A 804/A 804M, A 889/A 889M, A 937/A 937M, A 971, and Practice A 664.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Flat-Rolled Electrical Steels for Magnetic Applications

ASTM A1040-04 规范锻造碳钢、低合金钢、合金钢统一的标准等级组分的标准指南

1.1 This standard provides a guide to ASTM Subcommittees A01.02, A01.03, A01.06, A01.09, A01.11, A01.15, A01.19, A01.22, and A01.28 for specifying chemical composition limits of wrought carbon, low-alloy, and alloy steels. It is intended that these recommended grade composition limits be suitable for adoption by other standardization bodies that prepare standards for carbon, low-alloy, and alloy steel products, including discontinued steels.1.2 Included in this guide are the recommendations for determining the number of significant figures for specifying chemical composition.1.3 The carbon and alloy steel grades in all standards overseen by the aforementioned ASTM subcommittees have been included, except those grades applicable to restricted special end uses.1.4 Not addressed are minor composition modifications that a specific ASTM subcommittee may find necessary to accommodate effects of normal processing or to enhance fabricability by the producer or user, or both.1.5 Also not generally addressed (except where established by ASTM subcommittees) is a complete rationalization of all limits, especially where such would conflict with long-standing practices and is not justified by special technical effect.1.6 This guide does not address discontinued or formerly standard steel grades. A listing of such steel grades can be found in SAE J 1249. Also excluded from this guide are cast materials and welding filler metals.

Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

KS D ISO 946:2003 灰口铸铁.梁的无切口冲击试验

이 규격은 박편 형태의 흑연을 포함하는 회주철의 충격 강도 결정을 위한 요구 사항에 대

Grey cast iron - Beam unnotched impact test