H43 钢锭、钢坯 标准查询与下载
共找到 188 条与 钢锭、钢坯 相关的标准，共 13 页
本部分规定了压水堆核电厂承受强辐照的反应堆压力容器筒体用锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于采用实心钢锭制造的压水堆核电厂承受强辐照的反应堆压力容器筒体用16MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 1:Mn-Ni-Mo steel forgings for reactor pressure vessel shells in the beltline region
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
本部分规定了压水堆核电厂不承受强辐照的反应堆压力容器筒体用锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于采用实心钢锭制造的压水堆核电厂不承受强辐照的反应堆压力容器筒体用16MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 2:Mn-Ni-Mo steel forgings for reactor pressure vessel shells outside the beltline region
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
本部分规定了压水堆核电厂压力容器过渡段和法兰用的锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于压水堆核电厂压力容器过渡段和法兰用16MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 3:Mn-Ni-Mo steel forgings for transition rings and flanges of reactor pressure vessels
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
本部分规定了压水堆核电厂反应堆压力容器接管嘴用锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于压水堆核电厂反应堆压力容器接管嘴用16MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 4:Mn-Ni-Mo steel forgings for reactor pressure vessels nozzles
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
本部分规定了压水堆核电厂蒸汽发生器管板用锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于压水堆核电厂蒸汽发生器管板用18MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 6:Mn-Ni-Mo steel forgings for PWR steam generator tube plates
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
本部分规定了压水堆核电厂反应堆冷却剂泵主法兰用锰-镍-钼钢锻件的制造、试验、检验和验收等要求。 本部分适用于压水堆核电厂反应堆冷却剂泵主法兰用16MnNiMo合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants.Part 12:Mn-Ni-Mo steel main flange forgings for pressurized water reactor coolant pumps
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2011-07-01
- 实施
- 2011-10-01
Carbon steel blooms and billets for forgings (Amendment 2)
- ICS
- 77.140.20;77.140.85
- CCS
- H43
- 发布
- 2010-08-20
- 实施
本部分规定了20、16Mn和15MnNi碳钢和低合金钢锻件的制造、化学成分、力学性能、取样和验收等要求。 本部分适用于压水堆核电厂l、2、3级设备用碳钢和低合金钢锻件。 本部分不适用于热交换器管板和辅助泵轴锻件，亦不适用于主蒸汽系统、主给水流量控制系统、辅助给水系统和汽轮机旁路系统用锻件。
Carbon steel and low alloy steel for pressurized water reactor nuclear power plants-Part 1: Class 1,2,3 forgings
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2010-05-01
- 实施
- 2010-10-01
本部分规定了压水堆核电厂稳压器和蒸汽发生器接管嘴及孔盖用锰-镍-钼合金钢锻件的制造、试验、检验和验收要求。 本部分适用于压水堆核电厂稳压器和蒸汽发生器接管嘴(包括稳压器人孔座、波动接管嘴、阀门接管嘴、喷雾接管嘴和蒸汽发生器二次侧的人孔座、主给水接管嘴和辅助给水接管嘴等)及孔盖(包括稳压器人孔盖和蒸汽发生器人孔盖、眼孔盖和手孔盖等) 16MnNiMo和H18MnNiMo低合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants-Part 10: Mn-Ni-Mo steel forgings for pressurizer and steam generator nozzles and covers
- ICS
- 77.140.50
- CCS
- H43
- 发布
- 2010-05-01
- 实施
- 2010-10-01
本部分规定了压水堆核电厂稳压器筒体和封头用锰-镍-钼低合金钢锻什的制造、试验、检验和验收要求。 本部分适刚于压水堆核电厂稳压器筒体和封头用16MnNiMo低合金钢锻件。
Alloy steel for pressurized water reactor nuclear power plants-Part 11: Mn-Ni-Mo steel forgings for pressurizer shells and heads
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2010-05-01
- 实施
- 2010-10-01
本部分规定了压水堆核电厂l、2、3级设备用06Crl9Nil0、022Crl9Nil0、026Crl9Ni1ON、 06Crl7Nil2Mo2、022Crl7Nil2Mo2、026Crl8Nil2Mo2N、06Crl8NillTi奥氏体不锈钢锻件的制造、化学成分、力学性能和验收等要求。 本部分适用于压水堆核电厂1、2、3级设备用单件重量不大于10t的奥氏体不锈钢锻件。
Stainless steel for pressurized water reactor nuclear power plants-Part 1: Class 1,2 and 3 austenitic stainless steel forgings
- ICS
- 77.140.85
- CCS
- H43
- 发布
- 2010-05-01
- 实施
- 2010-10-01
1.1 This specification covers the requirements for chromium-carbon bearing quality stainless steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary Requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Stainless Anti-Friction Bearing Steel
- ICS
- 77.140.20
- CCS
- H43
- 发布
- 2009
- 实施
1.1 This specification covers the requirements for chromium-carbon bearing quality stainless steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary Requirements of an optional nature are provided and when desired shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Stainless Anti-Friction Bearing Steel
- ICS
- CCS
- H43
- 发布
- 2009
- 实施
This translation has been made based on the Amendment to the origi- nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provi- sion of Article 12 Clause I of the Industrial Standardization Law ap- plicable to the case of revision by the provision of Article 14. Consequently, JIS G 3251:1988 is partially replaced with this Amend- ment.
Carbon steel blooms and billets for forgings (Amendment 1)
- ICS
- 77.140.20;77.140.85
- CCS
- H43
- 发布
- 2008-03-20
- 实施
この規格は，転がり軸受に使用する高炭素クロム軸受鋼鋼材(以下，鋼材という。)について規定する。
High carbon chromium bearing steels
- ICS
- 77.140.10
- CCS
- H43
- 发布
- 2008-02-20
- 实施
- 2008-02-20
本标准规定了高压用热轧和锻制无缝钢管圆管坯的尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本标准适用于制造高压及其以上压力的锅炉、化肥设备、石油裂化装置等用途的无缝钢管的优质碳素钢、低合金结构钢、合金结构钢和不锈耐热钢热轧、锻制圆管坯
Hot-rolled and forged seamless steel pipe round billets for high pressure
- ICS
- 77.140.60
- CCS
- H43
- 发布
- 2007-03-06
- 实施
- 2007-09-01
本标准规定了热轧或锻制不锈钢无缝钢管圆管坯的订货内容、分类、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书等。 本标准适用于制造不锈钢无缝钢管用直径不大于250mm的热轧或锻制圆管坯。
Stainless steel seamless round tube bland
- ICS
- 77.140.60
- CCS
- H43
- 发布
- 2007-01-25
- 实施
- 2007-07-01
本标准规定了锻制用不锈钢坯的分类和牌号、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则和包装、标志、质量证明书等。 本标准适用于供锻制用的不锈钢热轧、锻制和挤压钢坯。
Stainless steel boooms and billets for forgings
- ICS
- 77.140.60
- CCS
- H43
- 发布
- 2007-01-25
- 实施
- 2007-07-01
This standard pertains to unannealed austenitic stainless-steel pipe that is longitudinal-seam or spiral-seam welded, 1/2 in. (13 mm) in nominal diameter and larger, intended for the transmission and distribution of water and for use in other water-sup
Stainless-Steel Pipe, ?in. (13mm) and Larger
- ICS
- 77.140.20
- CCS
- H43
- 发布
- 2007-01-01
- 实施
- 2007-03-01
1.1 This specification covers the chemical, mechanical, and physical requirements for available wrought alloy tool steel products. 1.2 These products, which include hot or cold finished bar, plate, sheet, strip, rod, wire, or forgings, are normally fabricated into tools, dies, or fixtures. The selection of a material for a particular application will depend upon design, service conditions, and desired properties.1.3 The values stated in inch-pound units are to be regarded as standard. The values given parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Tool Steels Alloy
- ICS
- 77.140.10 (Heat-treatable steels)
- CCS
- H43
- 发布
- 2007
- 实施
