H92 冶炼设备 标准查询与下载

YS/T 119.5-2008 氧化铝生产专用设备热平衡测定与计算方法 第5部分:蒸发器

本部分规定了氧化铝厂蒸发器组的热平衡测定与计算基准、测定条件、测定项目及测定计算方法。 本部分适用于氧化铝厂铝酸钠溶液蒸发器的热平衡测定和计算。

Determination and calculation of heat balance of special equipments for alumina production.Part 5: Evaporator

YS/T 119.1-2008 氧化铝生产专用设备热平衡测定与计算方法 第1部分:熟料回转窑系统

本部分规定了氧化铝厂熟料回转窑系统热平衡测定与计算基准、测定条件、测定项目及测定计算方法。 本部分适用于以煤粉或燃料油为燃料、生料掺入无烟煤的熟料烧成回转窑系统的热平衡测定和计算，不适用于窑外烘干预热的回转窑。

Determination and calculation of heat balance of special equipments for alumina production.Part 1: Clinder rotary kiln system

YB/T 4175-2008 冶金用钢水罐

本标准规定了冶金用鋼制焊接鋼水罐的類別、材料、設計、製造，檢驗和试验，质量證明和書，HN 漆、.包装，贮存和运输的要求。 本标准适用于额定容量不大于 400t 的治金用鋼制焊接鋼水罐。

Steel water tank for metallurgy

NF E88-005:2008 机械安全.连续铸钢机械和设备的安全要求

Safety of machinery - Safety requirements for machinery and equipment for the continuous casting of steel.

JIS G 0702 ERRATUM 1:2008 勘误表

ERRATUM

YS/T 664-2007 铝用炭素生产专用设备 热平衡测定与计算方法 热媒炉

本标准规定了炭素厂热媒炉的热平衡测定与计算基准、测定条件、测定项目及测定计算方法。 本标准适用于以燃油、煤气、余热烟气为燃料的热媒炉的热平衡测定与计算。

Determination and calculation of heat balance of special equipments for carbon production.Heating medium furnace

YS/T 663-2007 电解铝生产专用设备 热平衡测定与计算方法 铝液保持炉

本标准规定了电解铝生产铝液保持炉的热平衡测定与计算基准、设备状况、热平衡测定条件、测定项目和方法、热平衡计算、热效率及主要技术指标及热平衡测定分析与改进建议。 本标准适用于电解铝生产中以重油、煤气、天然气为供给能的铝液保持炉的热平衡测定与计算。

Methods for determinanation and calculation of heat balance of special equipments for aluminium production.Aluminium holding furnace

YB/T 011-2007 高炉设备主要参数

本标准规定了高炉的有效容积级别、高炉内型各部名称及部分高炉设备的主要参数。 本标准适用于有效容积1000m~5000m级高炉。

Main parameters of blast furnace equipment

JB/T 7851-2006 冶炼机械 术语

本标准规定了钢铁和有色金属冶炼机械的基本和常用术语，包括：炼焦机械、造块设备、耐火材料 设备、炼铁设备、炼钢设备、连铸设备、冶金除尘设备、检测、控制与自动化等方面的术语及其定义。 同时给出了英文对应词。 本标准适用于科研、工程设计文件、出版物中冶炼设备的称谓。

Metallurgical machinery Term

YS/T 549-2006 鼓风烧结机

Blast sintering machine

BS EN 14681:2006 机器安全性.采用电弧炉生产钢用机械和设备安全要求

This European Standard specifies the general safety requirements for electric arc furnaces (EAF) to melt steel not containing radioactive material. This European Standard deals with all significant hazards, hazardous situations and events pertinent to EAF, when used as intended and under conditions foreseen by the manufacturer, but also includes foreseeable faults and malfunctions in case of misuse. This European Standard specifies also criteria for the plant and equipment integrated in the production process. This European Standard specifies the requirements to ensure the safety of persons which are to be met during the design, assembly, transport, commissioning, operation, maintenance and decommissioning of the equipment. This European Standard assumes that installations are operated and maintained by adequately trained and competent personnel. Manual intervention for setting, adjustment and maintenance is accepted as part of the normal use of the equipment. This European Standard covers the following equipment (see Annex B): ? EAF with AC technology (alternating current); ? EAF with DC technology (direct current); ? scrap pre-heating technology; ? associated equipment/devices according Annex B. The following equipment is not covered by this European Standard: ? induction furnace; ? resistance-arc furnace; ? electron beam furnace; ? plasma furnace; ? other electrical furnaces used in secondary steelmaking. This European Standard does not specify safety requirements for the following equipment, which can be an integral or complementary part of the equipment covered by the Scope: a) cranes; b) scrap basket; c) transport car for scrap basket; d) elephant house (furnace encasing for environmental reasons); e) separate scrap drying equipment.

Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces

ISO 14420:2005 铝生产用碳质产品.焙烧阳极和成形碳产品.线性热膨胀系数的测定

This International Standard specifies a method to determine the coefficient of linear thermal expansion of carbonaceous or graphite materials (solid materials) for the production of aluminium between 20 ℃ and 300 ℃. It applies to baked anodes and shaped carbon products.

Carbonaceous products for the production of aluminium - Baked anodes and shaped carbon products - Determination of the coefficient of linear thermal expansion

YB/T 4037-2005 半石墨质高炉炭块

本标准规定了半石墨质高炉炭块的技术要求、检验规则、试验方法、预组装及检查方法。 　　本标准适用于以高温电煅烧无烟煤、石墨为主要原料制成的用于砌筑炼铁高炉的内衬材料。

Semi-Graphite Blast Furnace Carbon Block

YS/T 119.11-2005 氧化铝生产专用设备 热平衡测定与计算方法 第11部分 单套管预热-高压釜溶出系统

本部分规定了氧化铝生产单套管预热-高压釜溶出系统的热平衡测定与计算基准、测定条件、测定项目及计算方法。 本部分适用于氧化铝生产以蒸汽为供给能的单套管预热-高压釜溶出系统的热平衡测定与计算。

Determination and calculation method of heat balance of special equipments for alumina production-Part 11:Tube prepare-high pressure autoclave system

YS/T 119.10-2005 氧化铝生产专用设备.热平衡测定与计算方法.第10部分:板式降膜蒸发器系统

本方法规定了氧化铝厂板式降膜蒸发器系统的热平衡测定与计算基准、测定条件、测定项目及计算方法。 本方法适用于氧化铝厂铝酸钠溶液板式降膜蒸发器系统的热平衡测定与计算。

Determination and calculation method of heat balance of special equipments for alumina production - Part 10: Plate falling-film evaporator system

YS/T 119.9-2005 氧化铝生产专用设备 热平衡测定与计算方法 第9部分 流态化焙烧炉系统

本部分规定了氧化铝厂氢氧化铝流态化焙烧炉系统的热平衡测定与计算基准、测定条件、测定项目及计算方法。 本部分适用于以燃油为燃料的氢氧化铝流态化焙烧炉系统的热平衡测定与计算。

Determination and calculation method of heat balance of special equipments for alumina production-Part 9:Fluidized baking-furnace system

YS/T 119.8-2005 氧化铝生产专用设备.热平衡测定与计算方法.第8部分:气态悬浮焙烧系统

本部分规定了氧化铝厂气态悬浮焙烧系统的热平衡测定与计算基准、测定条件、测定项目及计算方法。 本部分适用于氧化铝厂以重油或煤气为燃料的氧化铝气态悬浮焙烧系统的热平衡测定和计算。

Determination and calculation method of heat balance of special equipments for alumina production - Part 8: Gaseity suspension calcine system

YS/T 481-2005 铝电解槽能量平衡测试与计算方法 五点进电和六点进电预焙阳极铝电解槽

本标准规定了冰晶石-氧化铝熔盐电解法密闭型中间点式下料大面五点和大面六点进电预焙阳极铝电解槽能量平衡的测试方法与计算方法。 本标准适用于冰晶石-氧化铝熔盐电解法密闭型中间点式下料大面五点和大面六点进电预焙阳极铝电解槽能量平衡的测试与计算。

Aluminium cell test for energy balance and its calculation method-Five-point feed current and six-point feed current prebaked anode aluminium cell

YS/T 480-2005 铝电解槽能量平衡测试与计算方法 四点进电和两点进电预焙阳极铝电解槽

本标准规定了冰晶石-氧化铝熔盐电解法四点进电和两点进电预焙阳极铝电解槽能量平衡的测试方法与计算方法。 本标准适用于冰晶石-氧化铝熔盐电解法四点进电和两点进电预焙阳极铝电解槽能量平衡的测试与计算。

Aluminium cell test for energy balance and its calculation method-Four-point feed current and two-point feed current prebaked anode aluminium cell

BS ISO 17544:2004 铝生产用含碳材料.冷和微热捣实糊料.非烤糊料的可压实性测定

This International Standard describes a method of producing a compaction curve indicating the rammability of carbonaceous ramming pastes used to line cathodes utilized in the production of aluminium. Determination of the rammability enables a ramming paste with the optimum density to be selected.

Carbonaceous materials used in the production of aluminium - Cold and tepid ramming pastes - Determination of rammability of unbaked pastes