冶炼设备标准-分析测试百科网

ASTM D6354-98(2003) 用于铝生产的碳阴极块的取样计划和芯取样的标准指南

Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of a cathode block. 4.1.1 Test specimens obtained by this guide can be used by producers and users of cathode blocks for the purpose of conducting the tests in Note 1 to obtain comparative physical properties. Sampling shall not weaken the cathode or increase the likelihood of premature failure. Extreme care shall be exercised when taking vertically drilled samples.1.1 This sampling guide was developed for carbon cathode blocks used in the production of aluminum, and details procedures for taking test samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathodes are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the staistical basis or sampling given in ISO 5022 applies, further or modified requirements may, also, apply. 1.2 SI units are the standard in this guide. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and E1225.

Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

ICS: 77.020 (Production of metals)
CCS: H92
发布: 1998
实施

ASTM D6354-98 用于铝生产的碳阴极块的取样计划和芯取样的标准指南

1.1 This sampling guide was developed for carbon cathode blocks used in the production of aluminum, and details procedures for taking test samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathodes are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the staistical basis or sampling given in ISO 5022 applies, further or modified requirements may, also, apply. 1.2 SI units are the standard in this guide. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and E1225.

Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

ICS: 77.020 (Production of metals)
CCS: H92
发布: 1998
实施

YS 5002-1996 有色金属冶炼厂电力设计规范

Code for power design of non-ferrous metals smelters

ICS
CCS: H92
发布: 1996-09-04
实施: 1997-01-01

JB/T 7851-1995 冶炼设备术语

本标准规定了冶炼设备的术语及其定义。本标准适用于科研、工程设计文件、出版物中冶炼设备的称谓。

Smelting Equipment Terminology

ICS
CCS: H92
发布: 1995-12-01
实施: 1996-07-01

JIS G 0703:1995 电弧炉热平衡方法

この規格は，アーク炉（以下，炉という。)の実用的な試験における熱勘定の方式について規定する。

Method of heat balance for electric arc furnace

ICS: 17.200.10;25.180.01
CCS: H92
发布: 1995-03-01
实施

JIS G 0702:1995 连续式钢材加热炉的热平衡方法

この規格は，連続鋼材加熱炉(以下，炉という。)の熱勘定の方式について規定する。

Method of heat balance for continuous reheating furnace for steel

ICS: 17.200.10;25.180.01
CCS: H92
发布: 1995-03-01
实施

YS 5025-1995 铝电解厂通风与烟气净化设计规范

Code for ventilation and fume purification design of aluminium smelters

ICS
CCS: H92
发布: 1995-01-14
实施: 1995-06-01

YS 5024-1995 冶炼烟气制酸工艺设计规范

Code for process design of acid-making from smelting gases

ICS
CCS: H92
发布: 1995-01-14
实施: 1995-06-01

YB/T 064-1994 液压抓具

hydraulic gripper

ICS
CCS: H92
发布: 1994-09-27
实施: 1995-05-01

BS 7699-8:1994 电热装置安全性规范.第8部分:电渣重熔炉的特殊要求

Applies to remelting and some refining processes of metals through direct resistance heating of conductive slag. To be read in conjunction with BS EN 60519-1

Specification for safety in electroheat installations - Particular requirements for electro-slag remelting furnaces