J22 密封与密封装置 标准查询与下载

SAE J1453/3-2007 O型密封圈端面密封管接头用规范:第3部分:钢管接头、防水壁、旋转接头、铜焊管接头和封闭盖及SAE J 1926-2英制螺柱端连接管接头的要求、尺寸和试验

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers the requirements for "inch based" O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex wrenching flats are predominantly used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 3 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Connectors, Caps, and Connectors with SAE J 1926-2 Inch Stud Ends

JB/T 7757.2-2006 机械密封用Ｏ形橡胶圈

本标准规定了机械密封用O形橡胶圈的尺寸系列、极限偏差、技术要求、试验方法、检验规则及包装、运输和贮存等要求。 本标准适用于机械密封用。0形橡胶圈（简称O形圈）。

The rubber O-ring for mechanical seal

JB/T 10688-2006 聚四氟乙烯垫片 技术条件

本标准规定了聚四氟乙烯垫片的技术要求、检验、标志、包装和贮存。 本标准适用于聚四氟乙烯垫片。

Specifications of polyfluortetraethylene gaskets

JB/T 10689-2006 膨体聚四氟乙烯密封带 技术条件

本标准规定了膨体聚四氟乙烯密封带的术语和定义、要求、检验方法、检验规则、标志、包装、运输及贮存。 本标准适用于膨体聚四氟乙烯密封带（以下简称膨体PTFE密封带）。

Specifications for expanded polytetrafluoroethylene tape

JB/T 6374-2006 机械密封用碳化硅密封环 技术条件

本标准规定了机械密封用碳化硅密封环的产品分类、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于机械密封用反应烧结碳化硅、无压烧结碳化硅（固相、液相、加碳）、热压烧结碳化硅密封环（以下简称密封环）。

Specifications for silicon carbide rings of mechanical seal

DIN EN 681-2:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第2部分:热塑性弹体(包括修改件A1-2002 + A2-2005)

This standard specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of: 1) thermoplastic piping systems for non pressure waste water discharge (intermittent flow up to 95℃) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45℃ and intermittent flow up to 95℃); 3) thermoplastic rainwater piping systems. General requirements for finished joint seals are slso given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-2:2006-11

DIN EN 681-4:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第4部分:聚氨酯铸塑密封件(包括修改件A1-2002 + A2-2005)

This Standard specifies requirements for materials used in factory cast polyurethane sealing elements used in joints for drainage, sewerage and rainwater systems and non potable water supply for continuous flow up to 45℃. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, plastics and glass-reinforced plastics.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-4:2006-11

DIN EN 681-3:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第3部分:硫化多孔橡胶材料(包括修改件A1-2002 + A2-2005)

This standard specifies requirements for materials used in vulcanized rubber seals of celluar materials for non pressurized drainage, sewerage and rainwater systems and non-pressure non-potable water supply (continuous flow up to 45℃). General requirements for the finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product srandards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard is applicable to joint seals for pipeline materials of vitrified clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. Joint seals made with an enclosed void as part of their design are included in the scope of this European Standard.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-3:2006-11

DIN EN 681-1:2006 弹性密封件.给排水管道连接密封件材料要求.第1部分:硫化橡胶(包括修改件A1-1998 + A2-2002 + A3-2005和技术勘误AC-2002)

This Standard specifies requirements for materials used in vulcanized rubber seals for: 1) cold potable water supply (up to 50℃); 2) hot potable and non-potable water supply (up to 110℃); 3) drainage sewerage and rainwater systems (continuous flow up to 45℃ and intermittent flow up to 95℃. The different designations of seals specified are defined according to their type, application and requirements (see Table 4) General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevent product standards taking into account that the performance of pipe joints is a function of the seal material propertied, seal geometry and pipe joint design. This standard should be used where appropriate with product standards which specify performance requirements for joints. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastic. It is applicable to elastomeric components of composite or non composite seals. In case of composite seals for materials of hardness ranges from 76 IRHD to 95 IRHD the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function, or the long term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this European Standard.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber(includes Amendments A1:1998 + A2:2002 + A3:2005 and Corrigendum AC:2002); English version of DIN EN 681-1:2006-11

SAE J1926/3-2006 通用和液压传动用联接件.带ASME B1.1螺纹和O形圈密封油口和螺纹端头.第3部分:轻重型(S 系列)螺栓端头

This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them. Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 40 MPa for nonadjustable stud ends and up to 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.

Connections for General use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing Part 3: Light-Duty (L Series) Stud Ends

DIN EN 682:2006 弹性体密封件.输送气体和烃类液体的管道和配件用密封件的材料要求

This European Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 °C up to 50 °C and in special cases from -15 °C up to 50 °C, for the following: General applications (see Table 4, type G) a) gaseous fuel (manufactured, natural and liquefied petroleum gas [LPG] in gaseous phase); b) hydrocarbon fluids with aromatic content up to 30 % (V/V), including LPG in liquid phase. Special applications (see Table 4, type H) Materials suitable for carrying gaseous fuels containing gas condensates and hydrocarbon fluids of unrestricted aromatic content. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This European Standard should be used where appropriate with product standards which specify performance requirements for joints. This European Standard is applicable to joint seals for all pipeline materials including iron, steel, copper and plastics. In the case of composite seals requirements in 4.2.8 and 4.2.9 apply only when the materials used for any elastomeric parts come into contact with gaseous fuel or hydrocarbon fluid. Elongation at break, tensile strength, compression set and stress relaxation requirements for materials of hardness categories 80 and 90 apply only when they constitute that part of the seal which participates directly in the sealing function or in long term stability. This standard is not applicable to the following: a) seals made from cellular materials; b) seals with enclosed voids as part of their design; c) seals with requirements of resistance to flame or to thermal stress; d) seals which contain splices joining pre-vulcanized profile ends.

Elastomeric seals - Material requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids (includes Amendment A1:2005); English version of DIN EN 682:2006-10

JIS B 2405 AMD 1:2006 机械密封.通用要求(修改件1)

附属書1付表2の下段の中欄の"非弾性体"の“A=合浸された石綿”を削除する。

Mechanical seals -- General requirements (Amendment 1)

JIS B 2401 ERRATUM 1:2006 勘误

ERRATUM

KS B ISO 3601-1:2006 流体动力系统.O型密封圈.第1部分:内径、横截面、公差和尺寸识别代码

이 규격은 항공 우주 분야(A시리즈)뿐만 아니라 일반용(G시리즈)으로 유체 동력 시스템에

Fluid power systems－O－rings－Part 1：Inside diameters, cross－sections, tolerances and size identification code

DIN EN 14187-9:2006 冷用接缝密封胶.试验方法.第9部分:接缝密封胶的功能试验

This European Standard specifies a function test for cold applied joint sealants intended for use in joints in roads and airfield pavements in cold climate areas where the total joint movement can be greater than 35 % and the temperature can go below -25 ?

Cold applied joint sealants - Test methods - Part 9: Function testing of joint sealants English version of DIN EN 14187-9:2006-05

SAE J1037-2006 挡风玻璃垫圈管

This SAE Standard covers nonreinforced, extruded, flexible tubing intended primarily for use as fluid lines for automotive windshield waster systems which conform to the requirements of SAE J 942.

Windshield Washer Tubing

NAVY MIL-DTL-81997 D (1)-2006 灵活透明的起静电防护作用的胶套和衬垫

This specification covers flexible, electrostatic-protective, transparent pouches used in military preservation.

POUCHES, CUSHIONED, FLEXIBLE, ELECTROSTATIC-PROTECTIVE, TRANSPARENT

DLA AN901 REV 9-2006 金属管接合面的密封件衬垫

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

GASKET - METAL TUBE CONNECTION SEAL

DLA AN887 REV 2-2006 编队用圆灯灯罩壳衬垫

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

GASKET - CIRCULAR FORMATION LIGHT COVER

ASTM C509-06 多孔弹性预成型垫片和密封材料标准规范

1.1 This specification applies to those elastomeric cellular materials of a firm grade that are manufactured in preformed shapes for use as gaskets and for use as sealing materials, in the form of compression seals or gaskets, or both, for glazing other building joint applications. Note 18212;For softer cellular elastomeric materials used in secondary sealing applications, refer to Specification D 1056.1.2 Test Method C 1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end useThe following precautionary caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.1.4 This test method is intended to determine the ability of compounds made from rubber or rubber-like materials to resist the effect of low temperatures that may cause them to become brittle and fracture or crack when bent. Standard specimens are exposed to specified low temperatures for definite periods after which the specimens are bent in a prescribed manner and any fracture or cracking noted. The procedure is commonly called the "Thiokol" method. Note 1Results obtained by this test method are influenced by the rate of flexing of the cooled specimens which can not be closely controlled in the prescribed apparatus. They are therefore of a qualitative nature and may not be closely reproducible over a range of several degrees of temperature depending on the speed of flexure. For more accurate determination of brittle temperature, and particularly in new specifications, Test Method D 746 is recommended.

Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material