J36 热处理 标准查询与下载

JB/T 11078-2011 钢件真空渗碳淬火

本标准规定了真空渗碳淬火的术语和定义、工艺分类及代号，设备及工艺材料、工艺及工艺过程、质量控制和检验、安全卫生和环保等要求。 本标准适用于钢件真空渗碳淬火的热处理工艺。

Vacuum carburizing and post-quenching of steel part

JB/T 10312-2011 钢箔测定碳势法

本标准规定了钢箔测定碳势法所用钢箔的材料及规格、钢箔渗碳装置及其操作程序基本要求、钢箔渗碳后碳含量的测量方法。 本标准适用于气体渗碳气氛碳势的测量，并可用于其他测量碳势方法的标定及碳势控制仪器的校核。

Steel-foil method for determination of carbon-potential of carburizing atmosphere

JB/T 4393-2011 聚乙烯醇合成淬火剂

本标准规定了聚乙烯醇合成淬火剂的技术条件。 本标准适用于钢件淬火冷却用的聚合物水溶性淬火介质—以聚乙烯醇为主要成分的合成淬火剂。

Polyvinyl alcohol of quenching media

JB/T 4392-2011 聚合物水溶性淬火介质测定方法

本标准规定了聚合物水溶性淬火介质的外观、固体含量、密度、运动粘度、折光率、凝点、浊点、酸碱度、稀释液冷却曲线和防锈试验等测定方法。 本标准适用于聚合物水溶性淬火介质性能的测定。

Test method of polymer quenchants

JB/T 11077-2011 大型可控气氛井式渗碳炉生产线热处理技术要求

本标准规定了大型可控气氛井式渗碳炉生产线的术语和定义、渗碳炉分类及生产线主要技术参数、设计和制造、配套设施、热处理技术、热处理工件品质控制与检验、可靠性、安全卫生、环境保护和能耗、检验和试验方法等要求。 本标准适用于最高工作温度为950℃，电加热大型可控气氛井式渗碳炉生产线的设计、制造、检验和验收。

The technical requirement of heat treatment for large pit-type controlled atmosphere carburizing furnace

ASME STP-PT-033-2011 焊后热处理(PWHT)对缺口韧性的降级

This report is a review of the literature on post weld heat treatment (PWHT) of steels used in ASME Code construction. It also includes a comparison of ASME PWHT rules with major European Codes.

DEGRADATION OF NOTCH TOUGHNESS BY A POST WELD HEAT TREATMENT (PWHT)

SAE AMS-H-6875B-2010 钢铁原材料的热处理

This specification covers the requirements for heat-treatment of four classes of steel and the requirements for furnace equipment, test procedures and information for heat-treating procedures, heat-treating temperatures and material test procedures. This specification is applicable only to the heat treatment of raw material; it does not cover the requirements for the heat treatment of steel parts. This specification also describes procedures that, when followed, will produce the desired properties and material qualities within the limitations of the respective alloys tabulated in Table IA, IB, IC and ID. Alloys other than those specifically covered herein may be heat treated using all applicable requirements of this specification.

Heat Treatment of Steel Raw Materials

DB13/T 1296-2010 中碳钢与中碳合金结构钢马氏体等级评定彩色金相法

本标准规定了中碳钢与中碳合金结构钢马氏体显微组织的检验方法及彩色金相图片。本标准适用于彩色金相法评定中碳与中碳合金结构钢马氏体等级。

Martensitic Grade Evaluation of Medium Carbon Steel and Medium Carbon Alloy Structural Steel by Color Metallographic Method

JIS B 6913 AMD 1:2010 钢铁的淬火和回火处理工艺(修改件1)

Process of quenching and tempering of iron and steel (Amendment 1)

JIS B 6914 AMD 1:2010 钢铁的渗碳和碳氮共渗,淬火和回火处理工艺(修改件1)

Process of carburizing and carbonitriding, quenching and tempering of iron and steel (Amendment 1)

JIS B 6912 AMD 1:2010 钢铁的感应淬火和回火处理工艺(修改件1)

Process of induction hardening and tempering of iron and steel (Amendment 1)

JIS B 6915 AMD 1:2010 钢铁的渗氮和软氮化处理工艺(修改件1)

Process of nitriding and nitrocarburizing of iron and steel (Amendment 1)

JIS B 6911 AMD 1:2010 钢铁的正火和退火处理工艺(修改件1)

Process of normalizing and annealing of iron and steel (Amendment 1)

DIN ISO 15787:2010 技术产品文件.热处理铁零部件.标志和表示(ISO 15787-2001)

This International Standard specifies the manner of presenting and indicating the final condition of heat-treated ferrous parts in technical drawings.

Technical product documentation - Heat-treated ferrous parts - Presentation and indications (ISO 15787:2001)

ASTM A991/A991M-10(2015) 对热处理钢产品使用的熔炉进行温度均匀性测量的标准试验方法

4.1 Furnaces for heat treatment of steel products are used in many industries, in many ways. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements. 4.2 The procedures in this test method may be used by those using, manufacturing, and providing calibration service for, heat treat furnaces used to process steel products. 1.1 This test method covers the procedures used to conduct a temperature uniformity survey on a furnace used to heat treat steel products. This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services. Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. 1.2 This test method covers heat treat furnaces in any of the following categories: 1.2.1 Continuous or semi-continuous conveyance furnaces, 1.2.2 Batch furnaces, and 1.2.3 Salt or liquid baths and fluidized beds. 1.3 This test method only applies when specified in the product specification or the purchase order. 1.4 Controlling a heat treatment of steel products using thermocouples attached to the extremities of each load is an alternative to performing a furnace survey. 1.5 By mutual agreement between the purchaser and the supplier of heat treat services, more stringent and/or additional requirements may be specified. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Conducting Temperature Uniformity Surveys of Furnaces Used to Heat Treat Steel Products

JB/T 4390-2008 高、中温热处理盐浴校正剂

本标准规定了高、中温热处理盐浴校正剂的一般要求、检验规则、试验方法、仲裁方法及包装、标志、贮存和运输。 本标准适用于热处理高温中性盐浴（工作温度1000℃～1350℃）和中温盐浴（工作温度700℃～1000℃）校正剂。

High and medium tempereture salt bath rectifier

JB/T 9207-2008 钢件在吸热式气氛中的热处理

本标准规定了钢件在吸热式气氛中的原料气、发生器、热处理炉、热处理质量控制、检验、安全及环保的基本要求。 本标准适用于渗碳、碳氮共渗、光亮或洁净淬火、正火、氮碳共渗及复碳等工艺。

Heat treatment of steels in endothermic atmospheres

JB/T 9197-2008 不锈钢和耐热钢热处理

本标准规定了不锈钢和热刚热处理的方法及所用的设备、工艺、工艺材料、质量检验和安全技术。 本标准适用于不锈钢和耐热钢热处理。

Heat treating for stainless steel and heat-resisting steel

JB/T 9208-2008 可控气氛分类及代号

本标准规定了热处理用可控气氛的分类及代号。 本标准适用于渗碳、碳氮共渗等化学热处理和保护加热的可控气氛。

Classifications and symbols of controlled atmospheres

JB/T 10896-2008 推杆式可控气氛渗碳线.热处理技术要求

本标注规定了钢件在推杆式可控气氛渗碳线生产过程控制中的技术要求、设备指标、电耗测定、可靠性、安全、环保等要求。 本标准适用于大批量生产，零件单件质量为0.1kg～40kg，渗碳层深度为0.3mm～3.0mm的渗碳钢制零件的各种渗碳处理。本标准中渗碳炉为电加热，不适用于燃料炉，也不适用于由推杆式炉与转底式炉组合而成的柔性生产线的热处理。

Technical requirement of heat treatment for pusher type controlled atmosphere carburizing line