J55 磨床 标准查询与下载

ISO 11148-9:2011 手持非电动工具.安全性要求.第9部分:模具磨机

Hand-held non-electric power tools - Safety requirements - Part 9: Die grinders

DIN EN 61029-2-4:2011 便携式电动工具的安全.第2-4部分:台式砂轮机的特殊要求(IEC 61029-2-4-1993,修订版本+A1-2001,修订版本).德文版 EN 61029-2-4-2011

Safety of transportable motor-operated electric tools - Part 2-4: Particular requirements for bench grinders (IEC 61029-2-4:1993, modified + A1:2001, modified); German version EN 61029-2-4:2011

ISO 11148-8:2011 手持非电动工具.安全性要求.第8部分:砂轮磨光机和抛光机

Hand-held non-electric power tools - Safety requirements - Part 8: Sanders and polishers

BS EN 61029-2-4:2011 便携式电机驱动工具的安全性.台式砂轮机特定要求

This clause of Part 1 is applicable except as follows: 1.1 Addition: This standard applies to transportable bench grinders (see Figure 101) and combined bench grinders (see Figure 107) with a wheel diameter and brush diameter not exceeding 200 mm, a thickness not exceeding 30 mm and a peripheral speed not exceeding 50 m/s, as defined in 2.101 and 2.107. The requirements for bonded abrasive products (wheel) are given in EN 12413. The requirements for brushes are given in EN 1083-2. Stationary grinding machines are covered by EN 13218. Bench grinders where the wheel partly runs in a water reservoir are not considered as tools with water supply.

Safety of transportable motor-operated electric tools. Particular requirements for bench grinders

NF C75-200-2-4:2011 可移动马达控制的电动机床的安全装置.第2-4部分:台式砂轮机的特殊要求.

Safety of transportable motor-operated electric tools - Part 2-4 : particular requirements for bench grinders.

ANSI/AIHA Z9.4-2011 磨料送风操作.固定位置外围设备的安全操作规程和通风

This standard shall apply to all operations in fixed location abrasive-blast enclosures in which an abrasive forcibly comes in contact with a surface by pneumatic or hydraulic pressure or by centrifu-gal force. It shall not apply to steam blasting, steam cleaning, or hydraulic cleaning methods in which work is done without the aid of abrasives. It also shall not apply to abrasive blasting conducted outdoors (e.g., bridges, water towers) even though temporary enclosures may be built at such locations.

Abrasive-Blasting Operations - Ventilation and Safe Practices for Fixed Location Enclosures

DIN EN 13218:2010 机械工具.安全性.固定磨床.德文版本EN 13218-2002+A1-2008+AC-2010

This standard specifies the technical safety requirements and/or protective measures to be adopted by persons undertaking the design, construction and supply (including installation and dismantling, arrangements for transport and maintenance)of stationary grinding machines as defined in 3.1 and 3.2 and intended to be used for the grinding of workpieces of cold metal.

Machine tools - Safety - Stationary grinding machines; German version EN 13218:2002+A1:2008 + AC:2010

JIS B 6220:2010 外圆无心磨床.精度检验

External cylindrical centreless grinding machines -- Test of the accuracy

NF C75-210:2010 便携式电动工具的安全性.第2-10部分:切断磨床的详细要求

Safety of transportable motor-operated electric tools - Part 2-10 : particular requirements for cutting-off grinders.

BS EN 60745-2-4:2009+A11:2011 手持式电动工具.安全性.盘式除外的砂轮机和抛光机的详细要求

Hand-held motor-operated electric tools. Safety. Particular requirements for sanders and polishers other than disk type

ANSI B11.9-2010 机床.磨床的安全性要求

The requirements of this standard apply to all stationary grinding machines used in either industrial or commercial applications and that utilize an abrasive product to change the shape, size or surface finish of any material.

Machine Tools - Safety Requirements for Grinding Machines

KS B ISO 8636-2:2009 机床工具.桥型磨床的试验条件.精度试验.第2部分:龙门机床

이 표준은 KS B ISO 230-1, KS B ISO 230-2, KS B ISO 230

Machine tools-Test conditions for bridge-type milling machines-Testing of the accuracy-Part 2:Travelling bridge(gantry-type) machines

DIN EN 792-9:2009 非电动手持工具.第9部分:安全要求.冲压磨床;EN 792-9:2001+A1:2008

EN 792 applies to hand-held non-electric power tools driven by rotary or linear motors, powered by compressed air, hydraulic fluid and intended to be used by one operator and supported by: -- the operator's hand or hands: a suspension, e. g. a balancer This part of EN 792 applies to hand-held, non-electric power tools fitted with collets and used far grinding and surface finishing and chamfering using mounted points, burrs and files and small wire brushes mounted on shafts. This part lists the significant hazards caused by such power tools and specifies safety requirements valid for different aspects of safety during their foreseeable lifetime. NOTE Grinders without collets for use with cones and plugs with threaded inserts are covered by EN 792-7. Power tools covered by this part of the standard: -- angle die grinders; reciprocating files; rotary files; -- straight die grinders. Special requirements and modifications on a hand-held power tool for the purpose of mounting it in a fixture are not covered by this part NOTE At the date of publication no die grinders driven by internal combustion engines are known.

Hand-held non-electric power tools - Safety requirements - Part 9: Die grinders(includes Amendment A1:2008); English version of DIN EN 792-9:2009-12

DIN EN 792-7:2009 非电动手持工具.安全要求.第7部分:研磨机,德文版本EN 792-7:2001+A1:2008

This European Standard applies to hand-held non-electric power tools driven by rotary or linear motors, powered by compressed air or hydraulic fluid and intended to be used by one operator and supported by: -- the operator's hand or hands; a harness; a suspension, e.g. a balancer. This European Standard applies to hand-held non-electric power tools intended for grinding and cutting-off, with bonded, coated and super abrasive products for use on all kinds of materials. This European Standard lists the significant hazards caused by such power tools and specifies safety requirements valid for different aspects of safety during their foreseeable lifetime. This part of the standard covers power tools used with: -- abrasive products with a peripheral operating speed less than or equal to 80 m/s; -- cutting-off wheels with a peripheral operating speed less than or equal to100 m/s; -- abrasive products with outside nominal diameter less than or equal to 230 mm; -- cutting-off wheels with outside nominal diameter less than or equal to 300 ram; wire brushes. This Part of the standard does not apply to: -- die grinders with collets which are treated in EN 792-9; -- polishers and sanders which are treated in EN 792-8; cutting-off machines used for construction, rescue purposes which are driven by an internal combustion engine which are treated in EN t454. There are no grinders covered by this Part of this European Standard driven by internal combustion engines. Typical abrasive products used together with hand-held grinders are listed in annex C. Special requirements and modifications on a hand-held power tool for the purpose of mounting it in a fixture are not covered by this part. NOTE At the date of publication no grinders driven by internal combustion engines are known.

Hand-held non-electric power tools - Safety requirements - Part 7: Grinders(includes Amendment A1:2008); English version of DIN EN 792-7:2009-12

NF E60-400:2008 机床.安全性.固定式磨床

Machine tools - Safety - Stationary grinding machines.

NF E60-400/IN1:2008 机床.安全性.固定式磨床

Machine tools - Safety - Stationary grinding machines.

DIN EN 13218:2008 机械工具.安全性.固定磨床

This standard specifies the technical safety requirements and/or protective measures to be adopted by persons undertaking the design, construction and supply (including installation and dismantling, arrangements for transport and maintenance) of stationary grinding machines as defined in 3,1 and 3.2 and intended to be used for the grinding of workpieces of cold metal. This standard deals with the significant hazards as listed in 4. This standard does not apply to honing, polishing and belt grinding machines. This standard applies to machines which are manufactured after the date of issue of this standard.

Machine tools - Safety - Stationary grinding machines; German version EN 13218:2002+A1:2008+AC1:2008

JB/T 6340.1-2008 轧辊磨床.第1部分:型式与参数

JB/T 6340的本部分规定了轧辊磨床的型式和参数。 本部分适用于新设计的、一般用途工作台移动式和砂轮架移动式轧辊磨床。

Rollgrinding machine.Part 1: Types and parameters

JB/T 6340.3-2008 轧辊磨床.第3部分:砂轮架移动式磨床精度检验

JB/T 6340的本部分规定了砂轮架移动式 轧辊磨床的几何精度和工作精度检验的要求及检验方去。 本部分本标准适用于最大磨削直径630mm～3150mm，最大顶尖距3000mm～1000Omm的砂轮架移动式、普通精度轧辘磨床。

Roll grinding machine.Part 3: Grinding machine with wheelhead moving style.Testing of the accuracy

KS B ISO 1985:2007 立轴矩台移动型平面磨床检.精度检验

이 규격은 KS B ISO 230-1에 기초하여 범용의 보통 정밀도를 가지는 직립축 테이블

Test conditions for surface grinding machines with vertical grinding wheel spindle and reciprocating table-Testing of the accuracy