J66 热处理设备 标准查询与下载

KS B 4158-2007 钻孔机主轴端

이 규격은 직립 드릴링 머신, 레이디얼 드릴링 머신 및 다축 드릴링 머신에 사용하는 주축

Spindle noses for drilling machines

DIN EN 1539 Berichtigung 1:2007 释放可燃物质的干燥机和烤箱.安全要求

Dryers and ovens, in which flammable substances are released - Safety requirements; German version EN 1539:2000, Corrigenda to DIN EN 1539:2000-03

DLA A-A-59375 VALID NOTICE 1-2006 盒型大气电热处理熔炉

A-A-59375, dated 27 June 2000, has been reviewed and determined to be valid for use in acquisition.

FURNACES, HEAT-TREATING, ELECTRIC, NATURAL ATMOSPHERE, BOX TYPE

ASHRAE 4833-2006 为蓄热式换热器设计用的有效性-传热单元数方法,制造公差影响

Impacts of Manufacturing Tolerances of the Effectiveness-Ntu Method for Regenerative Exchanger Design

Impacts of Manufacturing Tolerances of the Effectiveness-Ntu Method for Regenerative Exchanger Design

KS B ISO 10774:2005 固态燃料加热器.测定燃烧表面允许净空高度的试验方法

이 규격은 설치 장소에 옮겨지기 전에 완전히 조립되어 자유롭게 세울 수 있고, 가정용 붙

Solid fuelled heaters-Test method for determining allowable clearances from combustible surfaces

JB/T 10457-2004 液态淬火冷却设备 技术条件

本标准规定了金属合金制件在液态介质中实行淬火冷却设备的技术条件。 　　本标准适用于铁和非铁合金淬火和固溶处理冷却用的水、油、无机盐、碱水溶液、有机聚合物水溶液等的浸入式冷却设备。

Technological requirements of liquid quenching apparatus

ASHRAE AN-04-7-4-2004 氨水吸收传热和视觉确认的微通道吸收传递

Ammonia-Water Absorption Heat and Mass Transfer in Microchannel Absorbers with Visual Confirmation

Ammonia-Water Absorption Heat and Mass Transfer in Microchannel Absorbers with Visual Confirmation

ASHRAE 4727-2004 翅片管式换热器的自然对流换热

Natural Convection Heat Transfer for Fin-Tube Heat Exchangers

Natural Convection Heat Transfer for Fin-Tube Heat Exchangers

KS B 4153-2002 塑料铸模起模杆

이 규격은 플라스틱용 금형(사출, 압축 성형 및 트랜스퍼 성형)에서 사용하는 이젝터 핀 중

Main plates for moulds for plastics

KS B 4157-2002 塑料铸模浇铸轴衬

이 규격은 주로 플라스틱과 고무 사출용 몰드 금형에 사용하는 스프루 부시(이하 스프루 부시

Tools for moulding－Sprue bushes－Dimensions

DIN EN 746-5:2001 工业热处理设备.第5部分:盐浴热处理设备特殊安全要求

The document gives the specific hazards and safety requirements for the melting and use of molten salt that shall be provided by the manufacturer for Salt Bath Industrial Thermoprocessing Equipment, whether it is used as an independent unit or an integrated part of a plant. The limits of the equipment will include any transportation equipment which is located wholly or partially in the bath.#,,#

Industrial thermoprocessing equipment - Part 5: Particular safety requirements for salt bath thermoprocessing equipment; German version EN 746-5:2000

DIN EN 746-8:2001 工业热处理设备.第8部分:淬火设备安全特殊要求

Industrial thermoprocessing equipment - Part 8: Particular safety requirements for quenching equipment; German version EN 746-8:2000

KS B 6389-2000 卧式塑料注塑成型机

이 규격은 일반적으로 사용하는 플라스틱 성형을 위한 수평형 사출 성형기(이하 사출 성형기라

Horizontal type injection plastic moulding machines

BS EN 746-8:2000 工业热处理设备.淬火设备的特殊安全性要求

This part of EN 746 gives the specific hazards and safety requirements that shall be provided by the manufacturer for Quenching Equipment, whether it is used as an independent unit or an integrated part of a plant. This part of EN 746 does not cover specific hazards and safety requirements for Salt Bath bath equipment used as a quenching means (see EN 746-5:2000). This part of EN 746 does not cover the handling, storage, transport, disposal, transfer or regeneration of the quenching media and processed material outside the limits of the equipment. This part of EN 746 standard applies not only to the normal operation of the equipment but also to the safety of personnel and property when foreseeable faults occur in them. Examples of quenching equipment are shown in Fig. 1 and Fig. 2. NOTE: There are many variations in the design of quenching equipment. Only two examples of the various types are given in this text.

Industrial thermoprocessing equipment - Particular safety requirements for quenching equipment

BS EN 746-5:2000 工业热处理设备.盐浴热处理设备的特殊安全性要求

This part of EN 746 gives the specific hazards and safety requirements for the melting and use of molten salt that shall be provided by the manufacturer for Salt Bath Industrial Thermoprocessing Equipment, whether it is used as an independent unit or an integrated part of a plant. The limits of the equipment will include any transportation equipment which is located wholly or partially in the bath. This part of EN 746 does not cover the handling, storage, transport, disposal, transfer or regeneration of the salts and processed material outside the limits of the equipment. This part of EN 746 applies not only to the normal operation of the equipment but also to the safety of personnel and property when foreseeable faults occur. Examples of salt bath furnace set-ups are shown in Fig. 1, Fig. 2, Fig. 3 and Fig. 4. NOTE: There are many variations in the design of salt bath equipment. Only three examples of the various types are given in this text.

Industrial thermoprocessing equipment - Particular safety requirements for salt bath thermoprocessing equipment

DIN 17052-1:2000 热处理炉.温度均匀性的要求

The document applies to indirectly heated and internally electrically heated heat treatment furnaces for treatment of metallic materials.

Heat treatment furnaces - Part 1: Requirements for temperature uniformity

DLA A-A-59375-2000 盒型大气电热处理熔炉 [代替:DLA MIL-F-80258 A CANC 通告 1,DLA MIL-F-80258 A,DLA MIL-F-80258]

The General Services Administration has authorized the use of this commercial item description for all federal agencies.

FURNACES, HEAT-TREATING, ELECTRIC, NATURAL ATMOSPHERE, BOX TYPE [Superseded: DLA MIL-F-80258 A CANC NOTICE 1, DLA MIL-F-80258 A, DLA MIL-F-80258]

KS B 4181-2000 塑料铸模定心套

이 규격은 플라스틱용 금형에 사용하는 센터링 슬리브에 대하여 규정한다.

Centring sleeves of moulds for plastics

KS B 4171-2000 塑料铸模锥度锁

이 규격은 플라스틱용 금형에 사용하는 테이퍼 로크에 대하여 규정한다.

Taper lock of moulds for plastics

KS B 4166-2000 塑料铸模起模导杆

이 규격은 플라스틱용 금형에 사용하는 이젝터 가이드 핀에 대하여 규정한다.

Ejector guide pins of moulds for plastics