K44 高电压设备成套装置 标准查询与下载

JB/T 10617-2006 高压组合电器用金属波纹管补偿器

本标准规定了高压组合电器用金属波纹管补偿的产品分类、技术要求、试验方法、检验规则及标志、包装和贮存。

Metal bellows compensator used in high voltage combined electrical appliance

DL/T 979-2005 直流高压高阻箱检定规程

本规程规定了直流高压高阻箱(以下简称高阻箱)的计量性能要求、通用技术要求和计量器具控制。 本规程适用于准确度等级为0.1～10级，测试电压≤lOkV，总阻值≥10Ω的高阻箱的首次检定、后续检定和使用中的检验。 本规程不适用于有源高值电阻器，也不适用于在电路中作为永久性安装元件的电阻器。

Verification regulation of high voltage D.C. resistance box

SANS 61481:2005 带电操作.电压为1千伏到36千伏的便携式相位比较器

Applies to portable phase comparators with or without a built-in power source to be used on electrical systems for voltages from 1 kV to 36 kV a.c. and frequencies from 50 Hz to 60 Hz.

Live working - Portable phase comparators for use on voltages from 1 kV to 36 kV a.c.

IEEE Std C37.118-2005 电力系统相位同步器

Defines synchronized phasor measurements used in power system applications. Provides a method to quantify the measurement, tests to be sure the measurement conforms to the definition, and error limits for the test. Also defines a data communication protocol including message formats for communicating this data in a real-time system.

Standard for Synchrophasors for Power Systems

DL/T 672-1999 变电所电压无功调节控制装置订货技术条件

Ordering specification for controlling device of adjusting voltage and reactive power in substation

SANS 61284:1997 架空线．接头要求和试验

Applies to fittings for overhead lines of nominal voltage above 45 kV. May also be applied to fittings for overhead lines of lower nominal voltage and to similar fittings for substations.

Overhead lines - Requirements and tests for fittings

DL/T 597-1996 低压无功补偿控制器订货技术条件

Specification of low-voltage reactive compensation controls for order

IEC TR2 61233:1994 高压交流断路器 感性负载开合

High-voltage alternating current circuit-breakers - Inductive load switching

DL 5014-1992 330～500kV变电所无功补偿装置设计技术规定

本规定适用于330、500kV变电所内的330、500kV并联电抗器置，10～63kV并联电抗器和并联电容器装置，0.8～20kV静止补偿装置的新建程，扩建、改建工程可参照执行。 本规定不包括调相机。 无功补偿装置的设计必须执行国家的技术经济政策，并应根据安装点的电网条件、谐波水平、自然环境、运行和检修要求等，合理地选择装置型式，量，电压等级，接线方式，布置型式及控制、保护方式，做到安全可靠、技术经济理和运行检修方便。 遵照本规定设计的无功补偿装置，尚应符合现行的国家和部的有关准、规范、规程和规定。

Technical regulation for designing of reactive power compensation equipment for 330～500kV substations

BS 159:1992 高压母线和母线连接规范

Requirements for busbars and busbar connections which are components of a.c. high voltage electrical systems (above 1 kV), composed of metal, with air, oil, gas, solid or semi-solid insulation.

Specification for high-voltage busbars and busbar connections

BS EN 50069:1991+A1:1993 充气式高压开关装置和控制器用铸造和锻造铝合金的焊接复合封闭物用规范

This standard applies to welded composite enclosures of cast and wrought aluminium and aluminium alloy enclosures pressurized with dry air, inert gases, for example sulphur hexafluoride or nitrogen or a mixture of such gases, used in indoor or outdoor installations of high-voltage switchgear and controlgear, where the gas is used principally for its dielectric and/or arc-quenching properties, with rated voltages. — 1 kV and up to and including 52 kV and with gas-filled compartments with design pressure — and with rated voltage 72,5 kV and above. The enclosures comprise parts of electrical equipment not necessarily limited to the following examples: circuit-breakers; switch-disconnectors; disconnectors; earthing switches; current transformers; voltage transformers; surge arrestors; busbars and connections. The scope covers also pressurized components such as the centre-chamber of live tank switchgear and controlgear, gas-insulated current transformers, etc. 2.2 Production The production of the enclosures shall be in accordance with documented welding procedures which shall be carried out by well trained and supervised welding personnel. Where International Standards (ISO or CEN) are not available, National Standards may be used. NOTE This standard will be revised as soon as possible when ISO or CEN standards covering the various aspects are available. 2.3 Quality assurance It is the intention of this standard, that the switchgear manufacturer shall be responsible for achieving and maintaining a consistent and adequate quality of product. Sufficient examinations shall be made by the enclosure manufacturer to ensure that the materials, production and testing comply in all respects with the requirements of this standard and ISO 6213:1983. Inspection by the user’s inspectors shall not absolve the switchgear manufacturer from his responsibility to exercise such quality assurance procedures as to ensure that the requirements and the intent of this standard are satisfied. NOTE Reference should be made to the ISO 9000 series of standards for quality assurance systems.

Specification for welded composite enclosures of cast and wrought aluminium alloys for gas-filled high- voltage switchgear and controlgear

DL 5014-1992（条文说明） 330～500kV变电所无功补偿装置设计技术规定

Technical regulation for designing of reactive power compensation equipment of 330~500kV substations(explanation)