K52 发电机组 标准查询与下载

DB65/T 2219-2005 并网风力发电机组电能品质评估和测试方法

Measurement and assessment of power quality characteristics of grid connected stall regulation wind turbine generator system

DB65/T 2220.1-2005 并网失速型风力发电机组的安装、调试及验收标准第1部分：检验与地面试验

Installation test check and acceptance standard of grid connected stall regylation wind turbine generator system Part1:cheeck and factory test

DB65/T 2220.2-2005 并网失速型风力发电机组的安装、调试及验收标准第2部分：五百小时试运行规范

Installation test check and acceptance standard of grid connected stall regylation wind turbine generator system Part2:500 hours cimmissioning regulation

DB65/T 2218-2005 并网失速型风力发电机组 技术条件

Grid cinnected stall regulation wind turbine generator system Technical requirement

NF E90-079-5:2005 机械振动.旋转轴上测量机械振动的评定.第5部分:水力发电厂和泵站机组

Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 5 : machine sets in hydraulic power generating and pumping plants.

NF E37-301:2005 往复式内燃机驱动的交流发电机组.第1部分:用途、定额和性能

Reciprocating internal combustion engine driven alternating current generating sets - Part 1 : application, ratings and performance.

NF E37-302:2005 往复式内燃机驱动的交流发电机组.第2部分:发动机

Reciprocating internal combustion engine driven alternating current generating sets - Part 2 : engines.

BS EN 88528-11:2004 往复式内燃机驱动交流发电机组.旋转不间断电力系统.性能要求和试验方法

This International Standard, which forms part of the ISO 8528 series, specifies criteria, including performance and test methods, for rotary uninterruptible power systems (UPS) arising out of a combination of mechanical and electrical rotating machines. This standard applies to power supplies primarily designed for supplying uninterrupted a.c. power to the consumer. When operated without input mains feed, the power is provided by stored energy and/or reciprocating internal combustion (RIC) engine and the output power is provided by one or more rotating electrical machines. This part 11 applies to a.c. power supplies primarily designed for supplying uninterruptible electrical power for stationary land and marine use, excluding supplies for aircraft, land vehicles or locomotives. It also excludes power supplies where the output power is generated by static converters. (See IEC 62040-3.) The use of a rotary UPS installation to improve the quality of a.c. power supply, to provide voltage and/or frequency conversion, and to provide peak shaving is also described. For some specific applications (for example, essential hospital supplies, offshore, nonstationary applications, high rise buildings, nuclear, etc.) supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be used as a basis.

Reciprocating internal combustion engine driven alternating current generating sets - Rotary uninterruptible power systems - Performance requirements and test methods

SN/T 1621.2-2005 进出口电力设备检验规程 第2部分:往复式内燃机驱动的交流发电机组

本部分规定了对进出口往复式内燃机驱动的交流发电机组的要求、检验及判定。 本部分适用于陆用和船用发动机驱动的交流发电机组的进出口检验。 对于某些特殊用途（例如必要的医院供电、高层建筑等）或其他型式的往复原动机（例如沼气发动机、蒸气发动机），本部分也可参照执行。

Rules for the inspection of power equipment for import and export--Part 2:Reciprocating internal combustion engine driven AC generator sets

ISO 8528-3:2005 往复式内燃机驱动的交流发电机组.第3部分:发电机组用交流发电机

This part of ISO 8528 specifies the principal characteristics of Alternating Current (a.c.) generators under the control of their voltage regulators when used in generating set applications. It supplements the requirements of IEC 60034-1. NOTE At present no International Standard is available for asynchronous generators. When such an International Standard is published, this part of ISO 8528 will be revised accordingly. This part of ISO 8528 applies to a.c. generators used in a.c. generating sets driven by reciprocating internal combustion (RIC) engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies, high-rise buildings), supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as the basis for establishing any supplementary requirements. For a.c. generating sets driven by other reciprocating-type prime movers (e.g. steam engines) the provisions of this part of ISO 8528 should be used as a basis for establishing these requirements.

Reciprocating internal combustion engine driven alternating current generating sets - Part 3: Alternating current generators for generating sets

ISO 8528-5:2005 往复式内燃机驱动的交流发电机组.第5部分:发电机组

This part of ISO 8528 defines terms and specifies design and performance criteria arising out of the combination of a Reciprocating Internal Combustion (RIC) engine and an Alternating Current (a.c.) generator when operating as a unit. It applies to a.c. generating sets driven by RIC engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies and high-rise buildings) supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as a basis for establishing any supplementary requirements. For generating sets driven by other reciprocating-type prime movers (e.g. steam engines), the provisions of this part of ISO 8528 should be used as a basis for establishing these requirements.

Reciprocating internal combustion engine driven alternating current generating sets - Part 5: Generating sets

ISO 8528-2:2005 往复式内燃交流发电机组 第2部分:发动机

This part of ISO 8528 specifies the principal characteristics of a Reciprocating Internal Combustion (RIC) engine when used for alternating current (a.c.) generating set applications. It applies to RIC engines for a.c. generating sets for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies, high rise buildings), supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as the basis for establishing any supplementary requirements. The terms which define the speed governing and speed characteristics of RIC engines are listed and explained where they apply specifically to the use of the engine for driving a.c. generators. For other reciprocating-type prime movers (e.g. steam engines), the provisions of this part of ISO 8528 should be used as a basis for establishing these requirements.

Reciprocating internal combustion engine driven alternating current generating sets - Part 2: Engines

ISO 8528-6:2005 往复式内燃交流发电机组.第6部分:试验方法

This part of ISO 8528 specifies the test methods to be used for characterizing an entire generating set. It applies to alternating current (a.c.) generating sets driven by reciprocating internal combustion (RIC) engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies, high-rise buildings) supplementary requirements may be necessary. The provisions of this part of ISO 8528 are intended as a basis for establishing any supplementary requirements. For a.c. generating sets driven by other reciprocating type prime movers (e.g. steam engines), this part of ISO 8528 is intended as a basis for establishing these requirements. NOTE Existing test methods for the engine (ISO 3046-1 and ISO 3046-3) and generator (IEC 60034-2) are applicable for those components. The generating set manufacturer is responsible for specifying these characteristics and the tests to be performed to verify them.

Reciprocating internal combustion engine driven alternating current generating sets - Part 6: Test methods

ISO 8528-4:2005 往复式内燃交流发电机组.第4部分:控制装置与开关装置

This part of ISO 8528 specifies the criteria for controlgear and switchgear for generating sets with reciprocating internal combustion engines. It applies to Alternating Current (a.c.) generating sets driven by Reciprocating Internal Combustion (RIC) engines for land and marine use excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies and high-rise buildings), supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as a basis for establishing any supplementary requirements. For generating sets driven by other prime movers (e.g. steam engines), this part of ISO 8528 should be regarded as a basis for establishing these requirements.

Reciprocating internal combustion engine driven alternating current generating sets - Part 4: Controlgear and switchgear

ISO 8528-1:2005 往复式内燃交流发电机组.第1部分:用途、定额及性能

This part of ISO 8528 defines various classifications for the application, rating and performance of generating sets consisting of a Reciprocating Internal Combustion (RIC) engine, Alternating Current (a.c.) generator and any associated controlgear, switchgear and auxiliary equipment. It applies to a.c. generating sets driven by RIC engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies, high-rise buildings) supplementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as the basis for establishing any supplementary requirements. For other reciprocating-type prime movers (e.g. sewage-gas engines, steam engines), the provisions of this part of ISO 8528 should be used as a basis for establishing these requirements. Generating sets meeting the requirements of this International Standard are used to generate electrical power for continuous, peak-load and standby applications. The classifications laid down in this part of ISO 8528 are intended to help understanding between manufacturer and customer.

Reciprocating internal combustion engine driven alternating current generating sets - Part 1: Application, ratings and performance

IEEE 387/INT 1-2005 IEEE Std 387?-1995用IEEE标准解释文件

This is an interpretation of IEEE Std 387-1995. Interpretations are issued to explain and clarify the intent of a standard and are not intended to constitute an alteration to the original standard or to supply consulting information. Permission is hereby granted to download and print one copy of this document. Individuals seeking permission to reproduce and/or distribute this document in its entirety or portions of this document must contact the IEEE Standard Department for the appropriate license. Use of the information contained in this document is at your own risk.

IEEE Standards Interpretation for IEEE Std 387?-1995

ANSI/NECA 90-2004 住宅发电机组的安装推荐实施规程

This recommended practice defines the process of commissioning building electrical systems and provides sample guidelines for attaining optimum system performances which conform to design, specifications, and industry-accepted codes and standards.

Recommended Practice for Commissioning Building Electrical Systems

IEEE 958-2003 发电站中2400至13800V辅助系统上可调速交流传动装置的应用指南

Intends to cover the application of drive systems for use in electric power generation stations designed for connection to medium voltage electric service rated between 2400 V and 13800 V. Includes ASD terminology, theory of operation, and a discussion of the factors that can influence equipment selection.

Guide for the Application of AC Adjustable-Speed Drives on 2 400 13 800 V Auxiliary Systems in Electric Power Generating Stations

ARMY MIL-DTL-53133 C SUPP 1-2002 一般规格的5至60万千瓦交流电.柴油机驱动的.静音的战术的.装在滑动底座的发电机组(代替使用ARMY MIL-DTL-0053133 B NOTICE 1)

This supplement forms a part of MIL-DTL-53133C, dated 15 April 2002.

GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR [Use In Lieu Of: ARMY MIL-DTL-0053133 B NOTICE 1]

ARMY MIL-DTL-53133 C-2002 一般规格的5至60万千瓦交流电.柴油机驱动的.静音的战术的.装在滑动底座的发电机组

This commercial item description covers brown kraft paper used for general wrapping applications.

GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR