L18 滤波器、延迟线 标准查询与下载

ANSI/ASA S1.11-2004 倍频带和分数倍频带模拟和数字滤波器

Provides performance requirements for analog, sampled-data, and digital implementations of bandpass filters that comprise a filter set or spectrum analyzer for acoustical measurements. It supersedes ANSI S1.11-1986 (R1998), and is a counterpart to International Standard IEC 61260:1995 Electroacoustics & 8211; Octave-Band and Fractional-Octave-Band Filters. Significant changes from ANSI S1.11-1986 have been adopted in order to conform to most of the specifications of IEC 61260:1995

Specification for Octave-Band and Fractional-Octave-Band Analog and Digital Filters

IEC 61012-1:2004 用于恶劣环境中的数字通信用多芯和对称对/四芯电缆 第1部分：通用规范

Multicore and symmetrical pair/quad cables for digital communications to be used in harsh environments - Part 1: General specification

DLA QPL-28861-41-2004 射频/电磁干扰抑制滤波器和电容器一般规格

This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-PRF-28861. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

FILTERS AND CAPACITORS, RADIO FREQUENCY/ ELECTROMAGNETIC INTERFERENCE SUPPRESSION, GENERAL SPECIFICATION FOR

KS C IEC 60940:2003 抑制无线电干扰用电容、电阻、电感器及整套滤波装置的使用导则

서 문 이 규격은 1988년 제1판으로 발행된 IEC 60940 Guidance

Guidance information on the application of capacitors, resistors, inductors and complete filter units for radio interference suppression

KS C IEC 60939-2:2003 抑制电磁干扰用无源滤波装置.第2部分:分规范:安全试验恰当的无源滤波装置.试验方法和通用要求

이 규격은 IEC 60939-1의 일반 사항의 적용 범위에 있는 간섭 방지용 필터 소자

Complete filter units for radio interference suppression－Part 2：Sectional specification

NF C93-631-1:2003 经质量评定的声表面波(SAW)过滤器.第1部分:总规范

Surface acoustic wave (SAW) filters of assessed quality - Part 1 : generic specification.

IEC 60862-3:2003 经质量评定的声表面波(SAW)滤波器.第3部分:标准外形

Specifies the outline drawings for surface acoustic wave (SAW) filters with leaded enclosures.

Surface acoustic wave (SAW) filters of assessed quality - Part 3: Standard outlines

BS EN 60862-1:2003 经质量评定的声表面波(SAW)滤波器.总规范

This part of IEC 60862 specifies the methods of test and general requirements for SAW filters of assessed quality using either capability approval or qualification approval procedures.

Surface acoustic wave (SAW) filters of assessed quality. Generic specification

ANSI/IEEE 1531:2003 谐波过滤器的使用和规范指南

Addresses the selection of the 1. Components, 2. Protection and 3. Control of harmonic filters.

Guide for Application and Specification of Harmonic Filters

KS C IEC 60938-2-2:2003 抑制无线电磁干扰用固定电感器.第2-2部分:空白详细规范.电感器安全试验

서 문 이 규격은 1999년 제1판으로 발행된 IEC 60938-2-2 Fixed

Fixed inductors for electromagnetic interference suppression-Part 2-2:Blank detail specification-Inductors for which safety tests are required(only)

KS C IEC 60938-2:2003 抑制无线电干扰用固定电感器.第2部分:分规范

이 규격은 전자 간섭 억제용 고정 인덕터에 적용되며, 품목 규격인 KS C IEC 60

Fixed inductors for electromagnetic interference suppression－Part 2：Sectional specification

KS C IEC 60938-2-1:2003 抑制无线电磁干扰用固定电感器.第2-1部分:空白详细规范.电感器安全试验.评定等级为D级

서 문 이 규격은 1999년 제1판으로 발행된 IEC 60938-2-1 Fixed

Fixed inductors for electromagnetic interference suppression-Part 2-1:Blank detail specification-Inductors for which safety tests are required-Assessment level D

KS C IEC 60938-1:2003 抑制无线电磁干扰用固定电感器.第1部分:总规范

이 규격은 전기ㆍ전자 장비 및 기계의 내부에서 사용하거나 이것과 연계하여 사용하도록 설

Fixed inductors for electromagnetic interference suppression－Part 1：Generic specification

KS C IEC 60939-1:2003 抑制电磁干扰用无源滤波装置.第1部分:总规范

이 규격은 주파수가 100 Hz 이하이고 도체 사이의 전압이 직류, 교류(실효값)

Complete filter units for radio interference suppression－Part 1：Generic specification

IEEE 1531-2003 谐波过滤器的应用和规范

Addresses the selection of the 1. Components, 2. Protection and 3. Control of harmonic filters.

Guide for Application and Specification of Harmonic Filters

IEC 60862-1:2003 经质量评定的声表面波(SAW)滤波器 第1部分:总规范

Relates to surface acoustic wave (SAW) filters for use in telecommunications, measuring equipment, radar systems and consumer products. Gives general information and general methods concerning measurements and tests common to many types of SAW filters.

Surface acoustic wave (SAW) filters of assessed quality - Part 1: Generic specification

DIN EN 61260:2003 电声学.倍频程频带和分倍频程频带滤波器

This standard provides performance requirements and methods for testing the performance of analogue, sampled-data, and digital implementions of band-pass filters that comprise a filter set or spectrum analyser. The extent of the passband region of a filter's relative attenuation characteristic is a constant percentage of the midband frequency for all filters of a given bandwidth. The Amendment A1 concerns EMC, i.e. specifications regarding the immunity of the apparatus and regarding the upper limits on radio-frequency emissions.#,,#

Electroacoustics - Octave-band and fractional-octave-band filters (IEC 61260:1995 + A1:2001); German version EN 61260:1995 + A1:2001

NF C93-631-2:2003 经质量评定的表面声波(SAW)滤波器.第2部分:使用指南

Surface acoustic wave (SAW) filters - of assessed quality - Part 2 : guidance on use.

BS EN 60862-2:2002 经质量评定的声表面波(SAW)滤波器.使用指南

SAW filters are now widely used in a variety of applications such as TV, satellite communications, optical fibre communications, mobile communications and so on. While these SAW filters have various specifications, many of them can be classified within a few fundamental categories. This part of IEC 60862 includes various kinds of filter configuration, of which the operating frequency range is from approximately 10 MHz to 3 GHz and the relative bandwidth is about 0,02 % to 100 % of the centre frequency. It is not the aim of this standard to explain theory, nor to attempt to cover all the eventualities which may arise in practical circumstances. This standard draws attention to some of the more fundamental questions, which should be considered by the user before he places an order for a SAW filter for a new application. Such a procedure will be the user's insurance against unsatisfactory performance. Standard specifications, given in IEC 60862, and national specifications or detail specifications issued by manufacturers, define the available combinations of nominal frequency, pass bandwidth, ripple, shape factor, terminating impedance, etc. These specifications are compiled to include a wide range of SAW filters with standardized performances. It cannot be over-emphasized that the user should, wherever possible, select his SAW filters from these specifications, when available, even if it may lead to making small modifications to his circuit to enable standard filters to be used. This applies particularly to the selection of the nominal frequency.

Surface acoustic wave (SAW) filters of assessed quality - Guidance on use

JIS C 6703:2002 晶体滤波器总规范

この規格は，水晶フィルタの品目別通則であって，水晶フィルタに対する試験方法及び一般的要求事項を規定する。

Generic specification of crystal filters