L24 安装、接线连接件 标准查询与下载

ANSI/EIA 364-88:1995 电子连接器的残余磁力

Details a standard test method to measure the residual magnetism of a connector after exposure to a specified magnetic fiels.

Residual Magnetism for Electrical Connectors

ANSI/EIA 520FAAA:1995 已质量认证的(低电流)最大12位置的旋转式开关的详细规范

Covers Rotary Switch (low current rating) 12 positions maximum, Central mounting, 33 mm maximum width, 30 degree, 36 degree, 45 degree, 60 degree, 90 degree angles of throw. Multiple deck construction.

Detail Specification for Rotary Switches of Certified Quality (Low Current Rating) 12 Positions Maximum

ANSI/EIA 700A0AB:1995 1.27mm间距68回路存储插件互连系统的详细规范

Detail Specification for 1.27mm Pitch, 68 Circuit Memory Card Interconnect System

JIS C 6560:1994 同心插头、插座

この規格は，電子機器の回路接続のために使用する超小形単頭プラグ，小形単頭プラグ及び大形単頭プラグとそれらに適合するジャックについて規定する。

Concentric plugs and jacks

EIA SP07-DSEG93-1994 元件可焊性指导

Solderability of component leads, wire, terminals, and printed wiring boards (PFvBs) is a prerequisite for assembly solderability. While that may appear obvious, solder defects caused by poor solderability always have been common, so much so that many production people regard such defects as inevitable. While the solderability is rarely bad enough to threaten the integrity of the connection,1.2 military soldering specifications3 often require that each connection be inspected for defects and that those found be reworked. Not only is it expensive to look for defects, but rework poses a threat of damage, particularly to boards. The process used to solder, or rework, a connection is limited in its ability to overcome poor solderability, whether that process uses a soldering iron or the latest automated machine

COMPONENT SOLDERABILITY GUIDE

ITU-T T.505-1994 用于互换可处理形式和格式化形成的增强型结构及混合型内容文件的文件应用轮廓PM-26.远程信息处理业务的终端设备和协议

This Profile specifies an interchange format for the transfer of structured documents between equipments designed for word or document processing. Such documents may contain character, raster graphics and geometric graphics content. The documents that can

Document Application Profile PM-26 for the Interchange of Enhanced Structure Mixed Content Documents in Processable and Formatted Forms - Terminals for Telematic Services Study Group 8; 105 pp

ITU-R P.1060-1994 高频地面系统中影响频率共享的传播因素

The feasibility of frequency sharing in a particular scenario depends on compatibility, that is, meeting the specified protection ratio for the required percentage of time (recommended protection ratios for use in sound broadcasting and for the fixed se

Propagation Factors Affecting Frequency Sharing in HF Terrestrial Syatems

ITU-R M.1080-1994 倍增设备安装的数字选择性呼叫系统增强

that Recommendation ITU-R M.493-5, 9 5.2 has recommended that the Xlo digit of the DSC address always be the figure O and is reserved for future use

Digital Selective Calling System Enhancement for Multiple Equipment Installations

ITU-R BT.811-1-1994 增强型PAL和SECAM系统的主观评定

In both cases, two 4:3 monitors with different vertical scanning are needed. Therefore, extreme care should be exercised in matching the two monitors.

Subjective Assessment of Enhanced PAL and SECAM Systems

ANSI/IEEE 896.1Edition:1994 多处理器结构的底板母线规范:未来总线、逻辑层规范

Specifies the functional, electrical, and mechanical requirements for a set of signal lines that constitute a backplane bus and for the interfacing of boards connected to that bus.

Backplanes Bus Specification for Multiprocessor Architectures: Futurebus+, Logical Layer Specification

ANSI/EIA 468-B:1994 自动装卸用径向配置元件的引线绝缘带

This standard covers the lead taping requirements for components having radial configured leads, provided these components may be taped in accordance with the requirements of this document.

Lead Taping of Components in the Radial Configuration for Automatic Handling

SJ/T 9167.11-1993 插头和插座

1.1 本标准适用于插头和插座、软线连接器、某些类型的分接头以及烙铁和电器插头--所用的这些元件都是符合国家电气法规的。 1.2 本标准不适用于额定值超过200A或600V的装置。见4.2条。 医院用等级的装置 1.3 在72～84，85～93和94～99章中规定的要求适用于(除去危险地方用的以外)医院用的医院用等级的插座、插头和软线连接器，都应符合ANSI/NFPA NO.70-1984国家电气法规的517章。它们只适用于传统结构(ANSI.C-73)的，额定值为15或20A，185或250V的非锁紧型装置；插座只应规定为平嵌安装，而插头和连接器现场装配到软线上，既可以是直式(软线放在装置的背后)也可以是弯角型的(软线与主插头轴线成一角度)。 1.4 其他型式的装置，如工厂装配好的插头和连接器、具有锁紧结构的装置或用于危险场地的装置，可根据本标准中规定的医院用等级的装置测试程序来考核，并进行必要的修改以足以表示装置预期的用途。 1.5 本标准不适用于医院用模压电源线的插头。 1.6 当产品包含有新的或不同于过去制定标准时采用的性能、特性、元件、材料或系统，而且还包含有着火、电击或人身伤害危险时，应采用适当的附加元件要求和最终产品要求进行评定，而这些要求应是被确定为对保持本标准意图最初考虑的产品用户的安全水平是必要的附加要求。

Attachment plugs and receptacles

SJ/T 9167.14-1993 熔断器座

1.1 本标准适用于： A. 螺口式和S型插入式熔断器的熔断器座， B. CC.G.H.J.K.R和T类管状熔断器的熔断器座， C. 与用在螺口式熔断器的S型插入式熔断器相适配的装置。 这些熔断器座和装置预定用于符合美国国家电气规程的照明和电源电路中的熔断器。 1.2 本标准不适用于熔断连接插头，汽车照明保险装置，设计作为信号系统或仪器的保护装置，或用于保险丝的熔断器座。 1.3 CTL(电路限制)熔断器座是下述尺寸和结构的一种熔断器座，它与某类CTL配电盘或其他装置提供的物理机构相关联，以防止安装比设计的和额定的组装数目多的过流保护装置。 1.4 除1.5条规定的之外，具有连接多于4个非电源电路或其中延续电路结构的装置被判定为是配电盘而不认为是熔断器座。 1.5 下述特点的装置(1)具有连接多于4个但不多于12个支路结构的，(2)具有仅用于插入式熔断器的插座，和(3)特别设计用于封闭式支路保险装置认为并被判定为熔断器座。 1.6 专门设计用于封闭式支路保险装置或用于配电盘组件的熔断器座应按预定用途和按本标准的要求判定。

Fuseholders

ANSI/IEEE C12.7:1993 电度表座的美国国家标准要求

American National Standard Requirements for Watthour Meter Sockets

SJ/T 9555.3-1993 Q型小圆形插头座质量分等标准

本标准适用于Q型小圆形插头座质量分等。

Q-type circular miniature connectors--Quality grading standard

SJ/T 9555.2-1993 X型小圆形插头座质量分等标准

本标准适用于X型小圆形插头座质量分等。

X-type circular miniature connectors--Quality grading standard

SJ/T 9555.1-1993 P型插头座质量分等标准

本标准适用于P型插头座质量分等。

P-type connectors--Quality grading standard

ITU-T T.506-1993 用于互换可处理形式和格式化形式扩充的文件结构和混合型内容文件的文件应用轮廓PM-36.远程信息处理业务的终端设备和协议

The ITü-T (Telecommunication Standardization Sector) is a permanent organ of the International Telecommunication Union (Itü).

DOCUMENT APPLICATION PROFILE PM-36 FOR THE INTERCHANGE OF EXTENDED DOCUMENT STRUCTURES AND MIXED CONTENT DOCUMENTS IN PROCESSABLE AND FORMATTED FORMS

IEC 60760:1989/AMD1:1993 扁平式快速连接终端 修改1

Replaces tables Ia and Ib, IIa and IIb, IIIa and IIIb, figures 4 and 4a.

Flat, quick-connect terminations; amendment 1

IEC 60998-2-4:1993 家用和类似用途低压电路连接器件 第2-4部分:扭接式连接器件的特殊要求

Connecting devices for low-voltage circuits for household and similar purposes; part 2-4: particular requirements for twist-on connecting devices