L25 继电器、斩波器 标准查询与下载

DLA MS24179 REV N-2003 非密封III型 1 PST(N.O.)400安培电磁继电器

The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106.

RELAYS, ELECTROMAGNETIC, 400 AMPERES, 1 PST (N.O.), TYPE III, NON-HERMETICALLY SEALED

IEC 60255-22-7:2003 电气继电器.第22-7部分:量度继电器和保护装置的电气干扰试验.电源频率抗扰试验

This part of IEC 60255 is based on the concepts described in IEC 61000-4-16, referring to that publication where applicable, and specifies the general requirements for power frequency immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. The objective of the tests is to confirm that the equipment under test (EUT) will operate correctly when energised and subjected to short duration, conducted, common and differential mode power frequency disturbances applied to DC status inputs, at the rated frequency of the EUT, for example 16/3 Hz, 50 Hz and 60 Hz. The testing of pilot wire schemes between substations is not covered by this standard. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. The object of this standard is to state: - definitions of terms used; - test severity levels; - test equipment; - test set-up; - test procedures; - criteria for acceptance; - test report.

Electrical relays - Part 22-7: Electrical disturbance tests for measuring relays and protection equipment; Power frequency immunity tests

DLA MIL-R-19309 D-2003 灵敏继电器

This specification describes the requirements for the acquisition of a double-pole, double-throw, sensitive electromagnetic relay, Drawing 1521140. The coil is rated at one watt at a voltage of 31.6 V dc. The relay is used in the control of functional circuits which operate on a nominal dc voltage of 25 volts and dc current up to two amperes.

RELAY, SENSITIVE (FOR TORPEDO MARK 37 MOD 2)

DIN EN 61811-55:2003 机电式有或无继电器.第55部分:空白详细规范.经质量评定的机电式有或无电信继电器.11 mm X 7.5 mm (最大)底座的2组转换触点

Electromechanical all-or-nothing relays - Part 55: Blank detail specification; Electromechanical all-or-nothing telecom relays of assessed quality; Two change-over contacts, 11 mm x 7,5 mm (max.) base (IEC 61811-55:2002 + Corrigendum 1); German version EN

DIN EN 61811-54:2003 机电式有或无继电器.第54部分:空白详细规范.经质量评定的机电式有或无电信继电器.15 mm X 7.5 mm 底座的2组转换触点

This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.#,,#

Electromechanical all-or-nothing relays - Part 54: Blank detail specification; Electromechanical all-or-nothing telecom relays of assessed quality; Two change-over contacts, 15 mm x 7,5 mm base (IEC 61811-54:2002); German version EN 61811-54:2002

DIN EN 61811-53:2003 机电式有或无继电器.第53部分:空白详细规范.经质量评定的机电式有或无电信继电器.14 mm X 9 mm底座的2组转换触点

Electromechanical all-or-nothing relays - Part 53: Blank detail specification; Electromechanical all-or-nothing telecom relays of assessed quality; Two change-over contacts, 14 mm x 9 mm base (IEC 61811-53:2002); German version EN 61811-53:2002

DLA MS25467 REV E-2003 I型4 PDT,5安培焊接终端栓钉安装磁力锁密封电磁继电器

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil.

RELAYS, ELECTROMAGNETIC, 5 AMPERES, 4 PDT TYPE I, MAGNETIC LATCH, SOLDER TERMINAL, STUD MOUNTED, HERMETICALLY SEALED

DLA MS27242 REV K-2003 I型1 PST N.O.,100安培密封电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106.

RELAYS, ELECTROMAGNETIC, 100 AMPERES, 1 PST N.O. TYPE I, HERMETICALLY SEALED

DLA MS25459 REV H-2003 I型4 PDT,5安培磁力锁密封电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense.The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106.

RELAYS, ELECTROMAGNETIC, 5 AMPERES, 4 PDT, TYPE I, MAGNETIC LATCH, HERMETICALLY SEALED

DLA MS25463 REV J-2003 I型6 PDT,5安培火箭安装磁力锁密封电磁继电器

1.Dimensions are in inches. 2. Metric equivalents are given for general information only. 3.Unless otherwise specified, tolerance is ±.010 (0.25 mm). 4. The use of diodes on ac relays is optional. Actual application must be shown on label. 5. Terminal numbers need not appear on relay headers provided there is affixed to the relay a suitable legible circuit diagram that permanently and positively identifies each terminal location specified hereon. 6/ Pins to be perpendicular to header surface within 1 degree. 7/ Relay is magnetically latched in both positions. Caution note to observe polarity must appear on relays with dc coils. 8/ Shock, vibration, and acceleration requirements application with coils de-energized.

RELAYS, ELECTROMAGNETIC, 6 PDT, 5 AMPERES, TYPE I, MAGNETIC LATCH, SOCKET MOUNTED, HERMETICALLY SEALED

DLA MS25468 REV L-2003 I型4 PDT,10安培焊接终端栓钉安装磁力锁密封电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense.The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106.

RELAYS, ELECTROMAGNETIC, 10 AMPERES, 4 PDT, TYPE I, MAGNETIC LATCH, SOLDER TERMINALS, STUD MOUNTED, HERMETICALLY SEALED

DLA MS25031 REV M-2003 II型2 PDT(N.O.),100 A非密封机械联锁继电器

1. Dimensions are in inches. 2. Metric equivalents are given for general information only.

RELAY, ELECTROMAGNETIC,100 AMPERES, 2 PDT, N.O. TYPE II, NON-HERMETICALLY SEALED, MECHANICALLY INTERLOCKED

DLA MS27222 REV M-2003 I型3 PST N.O.,50安培密封电磁继电器

Dimensions are in inches.

RELAYS, ELECTROMAGNETIC, 50 AMPERES, 3 PST N.O. TYPE I, HERMETICALLY SEALED

DLA MS27247 REV M-2003 I型2 PDT,10安培密封电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106.

RELAYS, ELECTROMAGNETIC, 10 AMPERES, 2 PDT TYPE I, HERMETICALLY SEALED

DLA MS25327 REV N-2003 I型4 PDT,10安培火箭安装密封电磁继电器

Referenced documents. In addition to MIL-PRF-6106, this specification sheet references the following documents. (Government documents are available on line at http://assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Society of Automotive Engineers documents are available from the Society of Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http://www.sae.org

RELAYS, ELECTROMAGNETIC, 10 AMPERES, 4 PDT, TYPE I, SOCKET MOUNTED, HERMETICALLY SEALED

DLA MS25466 REV F-2003 I型2 PDT,10安培焊钩栓钉安装磁力锁密封电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense.

RELAYS, ELECTROMAGNETIC, 10 AMPERES, 2 PDT TYPE I, MAGNETIC LATCH, STUD MOUNTED, SOLDER HOOKS, HERMETICALLY SEALED

DLA MS25329 REV M-2003 I型6 PDT,5安培火箭安装密封电磁继电器

Dimensions are in inches.

RELAYS, ELECTROMAGNETIC, 6 PDT, 5 AMPERES, TYPE I, SOCKET MOUNTED, HERMETICALLY SEALED

DLA MS24192 REV P-2003 非密封II型 3 PST(N.O.)25安培电磁继电器

This specification is approved for use by all Departments and Agencies of the Department of Defense.

RELAYS, ELECTROMAGNETIC, 25 AMPERES, 3 PST (N.O.) TYPE II, NON-HERMETICALLY SEALED

DLA MS25267 REV H-2003 I型4 PDT,5安培焊锡钩密封电磁继电器

Dimensions are in inches. Metric equivalents are given for general information only. Unless otherwise specified, tolerance is ±.010 (0.25 mm). Terminal numbers need not appear on relay headers provided there is affixed to the relay a suitable legible circuit diagram that permanently and positively identifies each terminal location specified herein. The use of diodes on ac relays is optional. Actual application must be shown on label. In the event of conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. Referenced Government documents of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this standard to the extent specified herein.

RELAY, ELECTROMAGNETIC, 5 AMPERES, 4 PDT, TYPE I, SOLDER HOOK, HERMETICALLY SEALED

DLA MS25918 REV J-2003 I型6 PDT,3安培电磁继电器

1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Terminal numbers do not appear on the relay header. There shall be affixed to the relay a suitable legible circuit diagram that identifies each terminal location specified. Circuit diagram shown above is the terminal view. 4. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 5. Referenced Government documents of the issue listed in that issue of the Department of Defense Index of Specifications and Standard (DoDISS) specified in the solicitation form a part of this standard to the extent specified herein. 6. For details see table I. 7. Unless otherwise specified, tolerance is ± .010 (0.25 mm). 8. Dash numbers D1 and D2 supersede and are completely interchangeable with dash numbers -1 and -2 respectively.

RELAYS, ELECTROMAGNETIC, 3 AMPERES, 6 PDT, TYPE I