共找到 336 条与 波导同轴元件及附件 相关的标准,共 23 页
Type GTP002 and GTP002A L band coaxial isolators detail specification for
Radio frequency and coaxial cable assemblies - Part 2-3: Detail specification for flexible coaxial cable assemblies
Radio frequency and coaxial cable assemblies - Part 3-2: Detail specification for semi-flexible coaxial cable assemblies for GSM use (0,8 GHz - 1 GHz)
Applicable to waveguides which can propagate two orthogonal polarizations of the same waveguide mode. In this way, the waveguide type is generally restricted to square or circular cross-section, such as waveguide with an octagonal cross-section. Three te
Methods of measurement for waveguides - Part 1: Decoupling and rotation of the plane of polarization
Describes the measurement of the power holding of a waveguide by the use of a multiplying loop. In this case, the input power required is much less (-10 dB to -12 dB) than when the waveguide under test is directly connected to a high power source.
Methods of measurement for waveguides - Part 8: Waveguide power holding capability
This part of IEC 1580 gives the means for determining the reflection coefficient at the junction of two similar rectangular waveguides due to the following imperfections: a) differences in the waveguide internal dimensions; b) lateral displacement between the waveguide axes in either the H or E plane; c) angular misalignment between the waveguide axes.
Methods of measurement for waveguides - Part 9: Reflection coefficient at rectangular waveguide interfaces
Deals with waveguide performance. Provides a means for determining the cut-off frequencies for the dominant and high order modes in waveguides of various types over the frequency range from 1 GHz to 27 GHz. It is only intended to be used as an appendix t
Methods of measurement for waveguides - Part 7: Graphical method for the determination of waveguide performance
Deals with intermodulation products in waveguides. A test procedure is given to characterise the level of unwanted signals caused by the presence of two or more transmitting signals in waveguides or waveguides assemblies.
Methods of measurement for waveguides - Part 2: Level of intermodulation products
本标准规定了2GHz~15GHz微波接力通信系统皱纹型椭圆软波导的产品分类、技术要求、试验方法、检验规程及标志、包装、运输、贮存。 本标准适用于2GHz~15GHz微波传输系统所用皱纹型椭圆软波导。
Technical conditions for elliptical flexible waveguides of microwave relay communication system
Deals with the sweep frequency method used for the measurement of return loss on waveguide and waveguide assemblies. Fundamentely the method involves measuring the amplitude of the reflected wave at the waveguide under test (WUT) input by means of a refl
Measurement of return loss on waveguide and waveguide assemblies
Surface acoustic wave (SAW) resonators - Part 2: Guide to the use
Waveguides,double ridge(band width ratio 2.4∶1),detail specification for
本规范适用于矩形波导传输线或矩形波导元件之间作机械连接和电气连接用的1类可扭软波导组件。
Waveguide assemblies,flexible,twistable,class 1,detail specification for
Waveguides,single ridge(band width ratio 2.4∶1),detail specification
High-power rotating joint of Aluminum waveguide Type BGJ-100-1/2
Waveguide assemblies,rectangular,90°H Plane,small radius bend detail specification for
Detail specification for model JWFX 13 3cm waveguide low power limiter
Waveguide assemblies,rectangular,90°E-Plane,small radius bend detail specification for
Rectangular aluninume Waveguide assemblies,rigid 90°step twist detail specification for
Detail specification for median power electrical dummy Load for 3cm aluminium waveguide
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号