L31 电声器件 标准查询与下载

BS EN 50332-1:2000 音响系统设备.与便携声学设备相连的耳机和头戴送受话器.最大声压水平测量方法学和限制.成套设备通用方法

The scope of this standard is to set up a suitable measuring methodology allowing accurate measurement of the maximum sound pressure level produced by consumer's headphones and earphones when associated with portable audio equipment. NOTE This standard does not apply to acoustically open or acoustically closed headphones associated with mains operated Hi-Fi home equipement nor does it apply to headphones for medical purposes (hard of hearing, etc.) or to headphones or similar parts being part of active hearing protection systems. Wireless headphones are neither included, conditions for them may be derived accordingly. Other requirements for safety, e.g. for noise protection in offices and industry are not affected by this standard. Requested features: - The method should be reproducible and easily applicable to every type and shape of headphone or earphone available on the market (good mechanical adaptability). - As safety and health are addressed, the method should faithfully reflect the pressure level effective at the user's hearing (good correlation with subjective tests). - And finally, it is desirable to establish a global measuring procedure, including each component in the chain: Portable set + specific test signal + associated headphone or earphone. The standard is split into two parts: - Part 1 deals with sets provided as a package equipment by the manufacturer. In this case, "Portable audio equipment" means the association of one set (compact cassette player, CD player, FM radio receiver, with its headphone or earphone. - Part 2 (under consideration at present time) gives guidelines to associate portable audio sets (compact cassette player, CD player, FM radio receiver, ...) with headphones or earphones coming from a different manufacturer.

Sound system equipment - Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - General method for "one package equipment"

IEC 61252:1993/AMD1:2000 电声学 个人声暴露计规范 修改1

This standard is about Electroacoustics - Specifications for personal sound exposure meters; Amendment 1

Electroacoustics - Specifications for personal sound exposure meters; Amendment 1

BS EN ISO 4869-4:2000 声学.听力保护器.电平相关声音恢复耳罩的有效声压级测量

This Technical Report specifies a physical test method for level-dependent sound-restoration ear-muffs. The physical measurements are made with the acoustic test fixture (ATF) according to ISO/TR 4869-3 or with a suitable head and torso simulator (HATS) with a suitable acoustic isolation (see clause 7). The results of these tests in combination with the results from the ISO 4869-1 tests can be used to estimate the effective A-weighted sound pressure level when sound restoration ear-muffs are worn. The method described is not suitable for measurement of the effective sound pressure level under ear-muffs in the case of impulsive noise nor for active noise reduction ear-muffs.

Acoustics. Hearing protectors. Measurement of effective sound pressure levels for level-dependent sound-restoration ear muffs

JIS T 1201-1:2000 听力计.第1部分:纯音色听力计

この規格は，オージオメータについての一般的要求事項及び聴覚域値レべルを育響心理学的検査法によって，標準化された基準域値レべルと比較して決定するために設計された，純音オージオメータの特別な要求事項について規定する。

Audiometers -- Part 1: Pure-tone audiometers

JIS T 1201-2:2000 听力计.第2部分:讲话听力设备

この規格は，例えば，語音了解度の測定などにおいて，標準化された方法で被検者に話音を呈示する手段を与えるために設計されたオージオメータ又はその部分に対ナる要求事項を規定する。

Audiometers -- Part 2: Equipment for speech audiometry

JIS C 5512:2000 助听器

この規格は、個人が身体に装着して使用し.内蔵電池を電源として電気増幅を行う補聴器について規定する。

Hearing aids

DIN EN 60118-6:2000 助听器.第6部分:助听器输入线路特性

The document specifies the electrical and safety characteristics of a circuit for an external electrical input to a personal hearing aid in order to ensure compatibility with external electrical or electroacoustic signal sources.

Hearing aids - Part 6: Characteristics of electrical input circuits for hearing aids (IEC 60118-6:1999); German version EN 60118-6:1999

ASTM E976-00 声音发射传感器响应的再现性测定的标准指南

1.1 This guide defines simple economical procedures for testing or comparing the performance of acoustic emission sensors. These procedures allow the user to check for degradation of a sensor or to select sets of sensors with nearly identical performances. The procedures are not capable of providing an absolute calibration of the sensor nor do they assure transferability of data sets between organizations. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response

NF C97-626:1999 助听器.第6部分:助听器输入电路特性

Hearing aids - Part 6 : characteristics of electrical input circuits for hearing aids.

BS EN 60118-6:1999 助听器.助听器用电气输入电路特性

Specifies the electrical, marking and safety characteristics for the electrical input circuit of hearing aids to ensure compatibility and satisfactory operation when they are connected to external equipment such as radios, record players, tape recorders, etc.

Hearing aids - Characteristics of electrical input circuits for hearing aids

DIN EN 60318-3:1999 电声学.人的头和耳的模拟器.第3部分:用于听力测定的超听力耳机校正用声耦合器(IEC 60318-3-1999)

The document describes an acoustic coupler for loading supra-aural audiometric earphones as specified in ISO 389-1 with a specified acoustic impedance, when calibrating audiometers, in the frequency range of 125 Hz to 8.000 Hz. The sound pressure developed by an earphone is not, in general, the same in the coupler as in person's ear. However, the IEC recommends its use as a simple and ready means for the exchange of specifications on audiometers and for the calibration of specified earphones used in audiometry.#,,#

Electroacoustics - Simulators of human head and ear - Part 3: Acoustic coupler for the calibration of supra-aural earphones used in audiometry (IEC 60318-3:1998); German version EN 60318-3:1998

DIN EN 60118-1:1999 助听器.第1部分:带感应耦合线圈输入的助听器（IEC 60118-1-1995+AI-1998)

The document specifies a method of determining the electroacoustic performance of hearing aids fitted with an induction pick-up coil and used in an audio-frequency magnetic field. The induction pick-up performance is measured in a loop simulating conditions of use in room applications.

Hearing aids - Part 1: Hearing aids with induction pick-up coil input (IEC 60118-1:1995 + A1:1998); German version EN 60118-1:1995 + A1:1998

NF C01-801:1999 电工词汇.第801章:声学和电声学

Electrotechnical Vocabulary. Chapter 801 : acoustics and electroacoustics.

IEC 60118-6:1999 助听器 第6部分:助听器输入电路的特性

This part of IEC 60118 specifies the electrical and safety characteristics of a circuit for an external electrical input to a personal hearing aid in order to ensure compatibility with external electrical or electroacoustic signal sources. In this standard, the hearing aid may include an adaptor (audio shoe) which incorporates connector systems described in IEC 60118-12.

Hearing aids - Part 6: Characteristics of electrical input circuits for hearing aids

BS EN 166101:1999 电子元器件质量评定协调体系.空白详细规范:表面声波(SAW)滤波器.性能认可

Blank Detail Specification: Surface Acoustic Wave (SAW) filters —Capability approval 1. RATINGS (see 2.4 of EN 166000 for preferred ratings) 2. CHARACTERISTICS (see 2.3 of EN 166000) 3. RELATED DOCUMENTS 4. MARKING 5. ORDERING INFORMATION 6. CERTIFIED TEST RECORDS 7. ADDITIONAL INFORMATION (not for inspection purposes) 8. INSPECTION REQUIREMENTS

Harmonized system of quality assessment for electronic components - Blank detail specification: surface acoustic wave (SAW) filters - Capability approval

BS EN ISO 5135:1999 声学.通过混响室测定空调终端设备、空调终端装置、阻尼器和阀门噪音的声音功率级

To be read in conjunction with ISO 3258:1976, ISO 3740:1980

Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room

ASA S3.45-1999 测试基本门厅功能程序

Procedures for testing basic vastibular function.

Procedures for Testing Basic Vestibular Function

IEC 60118-1:1999 助听器 第1部分:具有感应拾音线圈输入的助听器

This standard specifies a method of determining the electroacoustic performance of hearing aids fitted with an induction pick-up coil and used in an audio-frequency magnetic field.The induction pick-up performance is measured in a loop simulating conditions of use in room applications.

Hearing aids - Part 1: Hearing aids with induction pick-up coil input

BS EN 160101:1998 电子元器件质量评定协调系统.空白详细规范:经过质量评定装有的印制电路板电子模块.性能认可

Blank Detail Specification Printed board assembly modular electronic units of assessed quality Capability approval 1 INTRODUCTION 2 IDENTIFICATION OF THE DETAIL SPECIFICATION AND OF THE PBA 2.1 Front page of the detail specification (DS) 2.1.1 Standard catalogue PBA 2.1.2 Custom built PBA 2.2 Additional reference data 2.2.1 General 2.2.2 Recommended methods of handling and mounting 2.2.3 Functional description and range of options 2.2.4 recommended conditions of use (not for inspection purposes) 3 SUPPLEMENTARY INFORMATION 3.1 Marking 3.2 Ordering information 3.3 Related documents 4 INSPECTION REQUIREMENTS 4.1 General 4.2 Capability approval 4.3 Extended capability 4.4 Inspection schedules Annex A Recommended layout for first page of detail specifications for standard catalogue items Annex B Recommended layout for first page of customer detail specifications not intended for registration Annex C Recommended layout for a final inspection and test schedule

Harmonized system of quality assessment for electronic components - Blank detail specification: printed board assembly modular electronic units of assessed quality - Capability approval

BS EN 60318-3:1998 电声学.人头和耳模拟器.用于测听计的超级听力耳机校正用听力耦合器

This International Standard describes an acoustic coupler for loading supra-aural audiometric earphones as specified in ISO 389-1 with a specified acoustic impedance, when calibrating audiometers, in the frequency range of 125 Hz to 8 000 Hz. The sound pressure developed by an earphone is not, in general, the same in the coupler as in a person's ear. However, the IEC recommends its use as a simple and ready means for the exchange of specifications on audiometers and for the calibration of specified earphones used in audiometry. note:1) To be published.

Electroacoustics - Simulators of human head and ear - Acoustic coupler for the calibration of supra-aural earphones used in audiometry