共找到 1086 条与 机械量仪表、自动秤重装置与其他检测仪表 相关的标准,共 73 页
This European Standard specifies the metrological and technical requirements for non-automatic weighing instruments. It is intended to provide standardized requirements and testing procedures to evaluate the metrological and technical characteristics in a uniform and traceable way.
Metrological aspects of non-automatic weighing instruments
本检定规程适用于测量范围为(-0.1~500) MPa (表压、差压或绝压)的压力传感器(静态)的首次检定、后续检定和使用中检查。
Verification Regulation of Pressure Transducer (Static)
本型式评价大纲适用于(-0.1~500)MPa的电阻应变式压力传感器(静态)(以下简称传感器)的型式评价。
Program of Pattern Evaluation of Pressure Transducer
本大纲适用于分类编码为12322000的具有弹性敏感元件的记录式压力表、压力真空表及真空表(以下简称仪表)的型式评价,不适用于采用其他压力敏感元件以及电子存贮器储存数据的电子式压力记录仪表的型式评价。
Program of Pattern Evaluation of the Record Pressure Gauges, Pressure-Vacuum Gauges and Vacuum Gauges
本规范适用于测量范围在0.1 Pa~133 kPa的电容薄膜真空计的校准,其中包括绝压电容薄膜真空计和差压电容薄膜真空计。
Calibration Specification for Capacitance Diaphragm Vacuum Gauges
本规程适用于记录式压力表、压力真空表和真空表(以下简称压力表)的首次检定、后续检定和使用中检查。
Verification Regulation of Record Pressure Gauges, Pressure Vacuum Gauges and Vacuum Gauges
Non-automatic weighing instruments -- Metrological and technical requirements and tests -- Part 3: Weights and poises used in transaction or certification
Non-automatic weighing instruments -- Metrological and technical requirements and tests -- Part 2: Measuring instruments used in transaction or certification
State system for ensuring the uniformity of measurements. Automatic rail-weighbridges. Part 1. Metrological and technical requirements. Test methods
State system for ensuring the uniformity of measurements. Instruments for measuring the smoke of exhaust gases from the motor vehicles equipped with compression-ignition engines. Verification method
Geometrical product specifications(GPS)-Acceptance and reverification tests for coodinate measuring machines(CMM)-Part 2:CMMs used for measuring size
本规程适用于沥青黏韧性试验仪的首次检定、后续检定和使用中检查。
Bitumen Toughness and Tenacity Testing Machine
本规程适用于标准扭矩扳子的首次检定、后续检定和使用中检查。
Standard Torque Wrench
本检定规程适用于分度值为1 μm、0.2 μm、0.1 μm和0.02 μm斜块式测微仪检定器的首次检定、后续检定和使用中的检查。
Wedge-feet Calibrator for Micrometers
本规程适用于分度值不大于0. 5 μm的圆锥滚子标准件测量仪的首次检定、后续检定和使用中检查。
Standard Tapered Roller Tester
本规程适用于:分度值为0.01 mm或分辨力为0.001 mm,测微头示值范围为13 mm、25 mm、50 mm,测量上限不大于6 000 mm的接杆内径千分尺、单杆内径千分尺、数显接杆内径千分尺和数显单杆内径千分尺(以下简称内径千分尺)的首次检定、后续检定和使用中检查。
Internal Micrometers
Discontinuous totalizing automatic weighing instruments (totalizing hopper weighers) - Part 1: Metrological and technical requirements - Tests (OIML R 107-1:2007)
本规程适用于分度值不大于0.001 mm滚动轴承宽度测量仪的首次检定、后续检定和使用中检查。
Instruments for Measuring Rolling Bearing Width
本规程适用于测定非金属材料冲击强度的悬臂梁式冲击试验机的首次检定、后续检定和使用中检查。悬臂梁式冲击试验机又称艾氏(Izod)冲击试验机,以下简称试验机。
Cantilever-Beam (Izod-Type) Impact Testing Machine
本规程适用于测量上限不大于6 kN的不等臂标准测力杠杆(以下简称测力杠杆)的首次检定、后续检定和使用中检查。测量上限大于6 kN的测力杠杆可参照本规程进行。
Standard Lever for Measuring Force
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号