N60 实验室仪器与真空仪器综合 标准查询与下载

ANSI/ASTM E1323:2009 实验室测量规程的评估和结果数据的统计分析

Guide for Evaluating Laboratory Measurement Practices and the Statistical Analysis of the Resulting Data

ISO 648:2008 实验室玻璃器具.单一容量吸液管

Laboratory glassware - Single-volume pipettes

NF X20-704:2007 2级电子呼吸试验仪.对呼出的空气进行分析以估计乙醇浸透度.规范和试验方法

Class 2 electronic breath tester - Estimation of the alcohol impregnation by analysis of expelled air - Specifications and test methods.

DIN 12924-2:2007 实验室储藏用具 通风橱 第2部分:增加酸和热负荷的通风橱

This standard applies to fume cupboards which are suitable for open digestions (e.g. using perchloric acid, sulphuric acid and/or hydrofluoric acid) and specifies additional requirements to take the increased release of acid or alkali at higher temperatures into consideration.

Laboratory furniture - Fume cupboards - Part 2: Fume cupboards for increased acidic and heat load

KS B ISO 15212-1:2006 振荡型密度计.第1部分:实验室仪器

Oscillation-type density meters－Part 1：Laboratory instruments

KS B ISO 12771:2006 实验室塑料器皿.一次性血清吸量管

이 규격은 일회용 플라스틱 혈청 피펫, 배출 측정, 일반적 실험 목적의 요구 사항을 규정한

Plastics laboratory ware－Disposable serological pipettes

KS B ISO 12772:2006 实验室玻璃器皿.一次性微量血球容量计毛细管

이 규격은 두 타입의 일회용 유리제 모세관 튜브에 대한 상세를 제공한다. 플라스마와 셀의

Laboratory glassware－Disposable microhaematocrit capillary tubes

KS L ISO 648:2006 实验室玻璃器具.单一容量吸液管

이 규격은 국제적으로 수용할 수 있는, 일반적으로 실험실에서 사용하기 적합한 원마크 피펫에

Laboratory glassware-One-mark pipettes

NF X15-202:2006 实验室设备.实验室存储装置.要求和试验方法

Laboratory furniture - Storage units for laboratories - Requirements and test methods.

BS EN ISO 14644-3:2005 洁净室和相关控制环境.试验方法

ISO 14644-3:2005 specifies test methods for designated classification of airborne particulate cleanliness and for characterizing the performance of cleanrooms and clean zones. Performance tests are specified for two types of cleanrooms and clean zones: those with unidirectional flow and those with non-unidirectional flow, in three possible occupancy states: as-built, at-rest and operational. ISO 14644-3:2005 is not applicable to the measurement of products or of processes in cleanrooms or separative devices.

Cleanrooms and associated controlled environments - Test methods

SANS 17025:2005 对于测试和校准实验室的资质的一般要求

Specifies the general requirements for the competence to carry out tests and/or calibrations, including sampling. It covers testing and calibration performed using standard methods, non-standard methods, and laboratory-developed methods.Applicable to all

General requirements for the competence of testing and calibration laboratories

NF X50-061*NF EN ISO/IEC 17025:2005 检测和校准实验室能力的一般要求

General requirements for the competence of testing and calibration laboratories.

ISO 13528:2005 用实验室间对比进行技术检查的统计方法

This International Standard complements ISO Guide 43 (all parts) by providing detailed descriptions of sound statistical methods for organizers to use to analyse the data obtained from proficiency testing schemes, and by giving recommendations on their use in practice by participants in such schemes and by accreditation bodies. This International Standard can be applied to demonstrate that the measurement results obtained by laboratories do not exhibit evidence of an unacceptable level of bias. It is applicable to quantitative data but not to qualitative data.

Statistical methods for use in proficiency testing by interlaboratory comparisons

BS EN ISO 14644-7:2004 洁净室和相关的受控环境.分离装置(洁净空气罩、手套式操作箱、分离器和微环境)

ISO 14644-7:2004 specifies the minimum requirements for the design, construction, installation, test and approval of separative devices, in those respects where they differ from cleanrooms as described in ISO 14644-4 and 14644-5. The application of ISO 14644-7:2004 takes into account the following limitations: user requirements are as agreed by customer and supplier; application-specific requirements are not addressed; specific processes to be accommodated in the separative-device installation are not specified; fire, safety and other regulatory matters are not considered specifically; where appropriate, national and local regulations apply. ISO 14644-7:2004 is not applicable to full-suits.

Cleanrooms and associated controlled environments - Separative devices (clean air hoods, gloveboxes, isolators and mini-environments)

JIS B 9919:2004 无菌室的设计、建设和启用

この規格は，クリーンルーム施設の設計施工に要求される事項について規定する。これらの要求を満たすための特別な技術又は契約方法を規定するものではない。

Design, construction and start-up for cleanrooms

NF X44-110:2004 无菌室和相关控制环境.生物污染控制.第1部分:总则和方法

Cleanrooms and associated controlled environments - Biocontamination control - Part 1 : general principles and methods.

NF X44-111:2004 无菌室和相关控制环境.生物污染控制.第2部分:生物污染数据的评价和解释

Cleanrooms and associated controlled environments - Biocontamination control - Part 2 : evaluation and interpretation of biocontamination data.

ASTM E2312-04 洁净室材料试验的标准规程

1.1 This practice identifies test methods used to evaluate the properties of various materials and products used in cleanrooms and for cleanroom construction.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Tests of Cleanroom Materials

ASTM D6911-03 实验室分析用环境样品的包装和装运标准指南

This standard provides guidance in determining the most appropriate procedures for packaging and shipping environmental samples. Use of this guide by personnel involved in packaging and shipping environmental samples will facilitate safe, effective and compliant procedures.1.1 This standard provides guidance on the selection of procedures for proper packaging and shipment of environmental samples to the laboratory for analysis to ensure compliance with appropriate regulatory programs and protection of sample integrity during shipment.1.2 This standard does not address transport of hazardous wastes for disposal purposes.1.3 This standard does not address the selection of parameter-specific sample bottles or containers.1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of the many unique aspects of a project. The word "standard" in the title of this guide means only that the guide has been approved through the ASTM consensus process.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Packaging and Shipping Environmental Samples for Laboratory Analysis

ASTM E1325-02(2008) 与实验装置设计相关的术语

This standard is a subsidiary to Terminology E 456. It provides definitions, descriptions, discussion, and comparison of terms. 1.1 This standard includes those statistical items related to the area of design of experiments for which standard definitions appears desirable.

Standard Terminology Relating to Design of Experiments