N70 试验机与无损探伤仪器综合 标准查询与下载

JIS Z 2316-2:2014 无损检测.涡流检测.第2部分:仪器特征和验证

Non-destructive testing .Eddy current testing .Part 2: Instrument characteristics and verification

DIN EN 12668-3:2014 无损检测.超声波检验设备的表征和验证.第3部分:组合设备.德文版本EN 12668-3-2013

Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment; German version EN 12668-3:2013

NF A09-170-1*NF EN ISO 15548-1:2014 无损检测. 涡流检测设备. 第1部分: 仪器性能和验证

La présente partie de l'ISO 15548 identifie les caractéristiques fonctionnelles d'un appareil à courants de Foucault à usage général et fournit des méthodes pour les mesurer et les vérifier.L'évaluation de ces caractéristiques permet de donner une description bien définie de l'appareillage à courants de Foucault et d'assurer la comparabilité entre appareillages.Un système d'examen par courants de Foucault, cohérent et efficace, peut être conçu en choisissant méticuleusement les caractéristiques pour une application spécifique.Lorsque des accessoires sont mis en oeuvre, ils sont caractérisés en appliquant les principes de la présente partie de l'ISO 15548.La

Non-destructive testing - Equipment for eddy current examination - Part 1 : instrument characteristics and verification

NF A09-170-2*NF EN ISO 15548-2:2014 无损检测. 涡流检测设备. 第2部分: 探头性能和验证

La présente partie de l'ISO 15548 identifie les caractéristiques fonctionnelles d'un capteur à courants de Foucault et de ses éléments d'interconnexion et fournit des méthodes pour les mesurer et les vérifier.L'évaluation de ces caractéristiques permet de donner une description bien définie de l'appareillage à courants de Foucault et d'assurer la comparabilité entre appareillages.Un système d'examen par courants de Foucault, cohérent et efficace, peut être conçu en choisissant méticuleusement les caractéristiques pour une application spécifique.Lorsque des accessoires sont mis en oeuvre, il convient de les caractériser en appliquant les principes de la prés

Non-destructive testing - Equipment for eddy current examination - Part 2 : probe characteristics and verification

JJF 1445-2014 落锤式冲击试验机校准规范

本校准规范适用于落锤式冲击试验机的校准,落锤式冲击试验机包括非金属落锤式冲击试验机、金属落锤式冲击试验机,其他进行落重冲击试验的仪器可以参照本规范进行校准。

Calibration Specification for Falling Weight Impact Testing Machines

NF A09-120-2:2014 无损试验. 渗透检测. 第2部分: 渗透材料的检测

Non-destructive testing - Penetrant testing - Part 2 : testing of penetrant materials

NF A09-120-3*NF EN ISO 3452-3:2014 无损检测.渗透检测.第3部分:标准试验块

Non-destructive testing - Penetrant testing - Part 3 : reference test blocks

JB/T 11611-2013 无损检测仪器 涡流-磁记忆综合检测仪

本标准规定了数字式涡流-磁记忆综合检测仪(以下简称仪器)的术语和定义、要求、检验方法、检验规则和标志、包装、运输和贮存等内容。本标准适用于数字式涡流-磁记忆综合检测仪。

Non-destructive testing instrument.Eddy current and magnetic memory integrated testing instrument

JB/T 11731-2013 无损检测 超声相控阵探头通用技术条件

本标准规定了超声相控阵探头的分类、技术要求和检验方法。本标准适用于中心频率为0.5 MHz~15 MHz、阵元数为4~256的超声相控阵探头的型式检验和出厂检验。本标准也可作为用户订货的验收依据。

Non-destructive testing.General specification for ultrasonic phased array probe

JB/T 11601-2013 无损检测仪器 目视检测设备

本标准规定了目视检测设备的一般要求。目视检测在以下情况时,应使用设备:--被测物是可视的或由于环境因素不可接近,需要接近观察;--检测灵敏度不够的;--需要图像记录的。本标准包含设备检定。本标准适用于目视检测设备。

Non-destructive testing instrument.Visual testing equipment

DIN EN 13477-1:2013 无损检测. 声发射. 设备性能. 第1部分:设备概述; 德文版本EN 13477-1-2001

Non destructive testing - Acoustic emission - Equipment characterisation - Part 1: Equipment description; German version EN 13477-1:2001

JJG 117-2013 平板检定规程

本规程适用于铸铁平板和岩石平板(以下简称平板)的首次检定、后续检定和使用中检查。

Verification Regulation of Surface Plates

SAE J2488-2013 SAE No. 2 摩擦试验机 6000 r/min Steped Power Test

This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a 6000 r/min Stepped Power Test for the evaluation of wet friction system performance variation as a function of power level. This procedure uses an init

SAE No. 2 Friction Test Machine 6000 r/min Stepped Power Test

JJG 1083-2013 锚固试验机

本规程适用于锚固试验机（以下简称试验机）的首次检定，后续检定和使用中检查。

Anchorage Testing Machines

DIN EN 13100-4:2013 热塑性半成品焊接接头的无损检测. 第4部分:高压试验; 德文版本EN 13100-4-2012

This European Standard specifies the equipment and methods for the high voltage testing of butt or overlap welded joints in thermoplastic sheets for locating through-thickness defects only. It applies to new unused constructions only.

Non destructive testing of welded joints of thermoplastics semifinished products.Part 4: High voltage testing; German version EN 13100-4:2012

SAE J2490-2012 SAE No. 2 摩擦试验机 ŠPVT 试验

This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a µPVT Test for the evaluation of the variation of wet friction system performance as a function of speed, temperature, and pressure. This procedure is intended as a standard for both suppliers and end users. The only variables selected by the supplier or user of the friction system are: a. Friction Material; b. Fluid; and c. Reaction Plates. These three variables must be clearly identified when reporting the results of this test. If any of the test parameters or system hardware as described in this document are changed, other than the friction material, test fluid, or reaction plates, the data may not be reported as having been obtained using this document. This procedure is intended to evaluate the endpoint/midpoint ratios, midpoint and breakaway coefficients. The procedure can be used to demonstrate changes that occur between the different levels of engagement speed, sump temperature and apply pressure. Refer to SAE J2487, SAE J2488, or SAE J2489 for coefficient variations due to changes in power level. The procedure, as described in detail in Table 1, consists of four 50 cycle break-in levels at 3500 r/min with increasing steps of apply pressure, followed by 16 levels consisting of 25 dynamic engagements and one breakaway following completion of the 25th dynamic cycle. The 16 levels are achieved by varying initial engagement speed, apply pressure and oil sump temperature while the inertia is kept constant at 0.701 kg- m2.

SAE No. 2 Friction Test Machine ŠPVT Test

NF A09-010:2012 无损检测 - 无损检验人员的资格鉴定和认证.

Non-destructive testing - Qualification and certification of NDT personnel.

DIN CEN/TR 16332:2012 无损检测. 无损检测人员资格认证用EN ISO/IEC 17024的解释; 德文版本CEN/TR 16332-2012

Non-destructive testing - Interpretation of EN ISO/IEC 17024 for NDT personnel certification application; German version CEN/TR 16332:2012

JJF 1298-2011 高温蠕变、持久强度试验机型式评价大纲

本大纲适用于高温蠕变、持久强度试验机（以下简称试验机）的型式评价，也可用于指导生产过程中试验机产品的质量监督检查。

Program of Pattern Evaluation of High-Temperature Creep and Stress-Rupture Testing Machines

ASTM E2658-11 材料试验机速度验证的标准操作规程

Material testing requires repeatable and predictable testing machine speed. The speed measuring devices integral to the testing machines may be used for measurement of crosshead speed over a defined range of operation. The accuracy of the speed value shall be traceable to a National or International Standards Laboratory. Practices E2658 provides procedures to verify testing machines, in order that the indicated speed values may be traceable. A key element to having traceability is that the devices used in the verification produce known speed characteristics, and have been calibrated in accordance with adequate calibration standards. Verification of testing machine speed at a minimum consists of either or both of the following options: nbsp;nbsp;nbsp;Verifying the capability of the testing machine to move the crosshead at the speed selected. Verifying the capability of the testing machine to adequately indicate the speed of the crosshead. Where applicable, determine the testing machine's ramp-to-speed condition. This condition can be significant especially when verifying fast speeds or testing conditions with very short testing durations. This procedure will establish the relationship between the actual crosshead speed and the testing machine indicated speed and or selected setting. It is this relationship that will allow confidence in the reported displacement over time data acquired by the testing machine during use. Note 18212;Many material tests never reach the desired test speed. Unless the actual data from the material test is examined, it is often impossible to know if the test speed has been reached or is repeatable from test to test.1.1 These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standard calibration devices. This practice is not intended to be complete purchase specifications for testing machines. 1.2 These practices apply to the verification of the speed application and measuring systems associated with the testing machine, such as a scale, dial, marked or unmarked recorder chart, digital display, setting, etc. In all cases the buyer/owner/user must designate the speed-measuring system(s) to be verified. 1.3 These practices give guidance, recommendations, and examples, specific to electro-mechanical testing machines. The practice may also be used to verify actuator speed for hydraulic testing machines. 1.4 This standard cannot be used to verify cycle counting or frequency related to cyclic fatigue testing applications. 1.5 Since conversion factors are not required in this practice, either SI units (mm/min), or English [in/min], can be used as the standard. 1.6 Speed measurement values and or settings on displays/printouts of testing machine data systems-be they instantaneous, delayed, stored, or retransmitted-which are within the Classification criteria listed in Table 1, comply with Practices E2658. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practices for Verification of Speed for Material Testing Machines